SIGNALTEK Users Guide V1.0 English - Ideal Industries

More documents

Recommendations

Info

should be performed by an authorized IDEAL INDUSTRIES service center. Opening the <strong>SIGNALTEK</strong> housing or defacing the access seal voids the product warranty. Registration Owners are encouraged to register the instrument immediately upon purchase. Registered owner contact information is used to notify owners about new firmware or other product updates. Owner information is never sold or used outside of IDEAL INDUSTRIES. Service 7-2
8 Specifications Cable Types Voice/phone cable – USOC/RJ11/RJ12 interface Data cable – (STP/UTP) RJ45 for CAT 3/5e/6/6a/7 cabling Coax cable – via RJ45-to-F patch cord, series 59, 6 cabling (75 ohm) Cable Length Measurement TDR maximum distance: 140m/460ft Battery Life - Standard AA Alkaline Batteries Standby – 30 days Cable testing – 30 hours Monitoring – 4 hours Ports/Connections RJ45 shielded test interface port Mini-USB “A” device port Standard USB “B” host port DC power input for long term BERT monitoring Test Standards Qualification/BERT – IEEE 802.3 standard for Gigabit Ethernet link performance Wire map- EIA/TIA 568-B pairing. 568 A/B color code display options IDEAL INDUSTRIES Inc. 8-1
Page 1:
SIGNALTEK TM Cable Performance Test
Page 4 and 5:
IDEAL INDUSTRIES STANDARD WARRANTY
Page 6 and 7:
Table of Contents Table of Contents
Page 8 and 9:
Table of Figures Figure 1-1 T-568 A
Page 10 and 11:
testing is critical because the cab
Page 12 and 13:
? Web Performance - Performance tes
Page 14 and 15:
Cable types that can be tested with
Page 16 and 17: Table 1-2 Cable Test Ability Chart
Page 18 and 19: Table 1-3 Key and LED Functions But
Page 20 and 21: Batteries & Power Each SIGNALTEK ha
Page 22 and 23: Graphical User Interface Navigation
Page 24 and 25: Figure 1-5 AutoTest Tab - Inactive
Page 27 and 28: 2 Setup and Configuration The follo
Page 29 and 30: Autotest Modes SIGNALTEK will perfo
Page 31 and 32: Figure 2-7 Cable Performance Setup
Page 33 and 34: Figure 2-9 IP Address Setup When DH
Page 35 and 36: each cable can be found on the cabl
Page 37 and 38: Measurement Units This function con
Page 39 and 40: Language SIGNALTEK can support a va
Page 41: delete the file from the USB drive
Page 44 and 45: eport. Therefore, leaving blank fie
Page 46 and 47: Note: If sending the file to anothe
Page 48 and 49: Beginning an Autotest There are thr
Page 50 and 51: Note: The ping test is a low speed
Page 52 and 53: When there is a cable fault (open o
Page 54 and 55: Figure 5-3 Cable Performance Result
Page 56 and 57: excessive attenuation. Increased at
Page 58 and 59: conductor and shield) is present. A
Page 60 and 61: SIGNALTEK’s active LAN features c
Page 62 and 63: Can SIGNALTEK be damaged by pluggin
Page 65: 7 Care and Calibration Cleaning Cle
Page 69 and 70: 9 Customer Service Technical Assist
Page 71 and 72: IDEAL INDUSTRIES (U.K.) Limited 225
Page 73: Manual Part No. 6510-91-0003 Rev. A
show all

SIGNALTEK Users Guide V1.0 English - Ideal Industries

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?