SIGNALTEK Users Guide V1.0 English - Ideal Industries

More documents

Recommendations

Info

Note: If sending the file to another person by email or another method, make sure to copy the “SIGNALTEK.xsl” file in addition to the test file so the records can be properly viewed on the other PC. Printing Directly to a USB Printer SIGNALTEK is the only LAN Qualification tester that can print reports directly to a USB printer. Because SIGNALTEK uses the Linux operating system, not all USB printers are supported. Please check IDEAL’s website for a list of compatible printers. At the time of this writing only HP printers have been found to support the Linux native PCL driver included in SIGNALTEK. ? To print a job to a compatible printer, connect the printer to SIGNALTEK’s top USB port. A USB “A to B” cable is required for direct printing. These cables are available at any electronics or computer store. ? Change to the Job tab and highlight the job to be printed. ? Press the “Print” function key to send the job to the printer. Note: All tests in the selected job will be sent to the printer. The user interface will remain locked while the job is being sent to the printer. Figure 3-2 USB Printer Cable Test Storage & Management 3-4
4 Running Autotests The Autotest tab displays a listing of the tests that will be run with the Autotest button is pressed. The listing will change depending on the link status (indicated by the link status icon at the top of the screen) and the options selected in the Autotest Preferences screen. Figure 4-1 Autotest Tab The Autotest list will automatically update as the link status changes. When testing with the SIGNALTEK remote the link status icon will change to green when the remote has been detected. Pressing the Autotest button before the remote is detected (red link icon) the no-link test will run, only checking the wire map and length. In addition to the link icon on the display handset, the “LINK” LED on the remote handset will also light green if it detects the display handset. This makes single person operation easy since the operator will always know that the SIGNALTEK display and remote handsets are connected to the same link before starting an autotest. IDEAL INDUSTRIES Inc. 4-1
Page 1: SIGNALTEK TM Cable Performance Test
Page 4 and 5: IDEAL INDUSTRIES STANDARD WARRANTY
Page 6 and 7: Table of Contents Table of Contents
Page 8 and 9: Table of Figures Figure 1-1 T-568 A
Page 10 and 11: testing is critical because the cab
Page 12 and 13: ? Web Performance - Performance tes
Page 14 and 15: Cable types that can be tested with
Page 16 and 17: Table 1-2 Cable Test Ability Chart
Page 18 and 19: Table 1-3 Key and LED Functions But
Page 20 and 21: Batteries & Power Each SIGNALTEK ha
Page 22 and 23: Graphical User Interface Navigation
Page 24 and 25: Figure 1-5 AutoTest Tab - Inactive
Page 27 and 28: 2 Setup and Configuration The follo
Page 29 and 30: Autotest Modes SIGNALTEK will perfo
Page 31 and 32: Figure 2-7 Cable Performance Setup
Page 33 and 34: Figure 2-9 IP Address Setup When DH
Page 35 and 36: each cable can be found on the cabl
Page 37 and 38: Measurement Units This function con
Page 39 and 40: Language SIGNALTEK can support a va
Page 41: delete the file from the USB drive
Page 44 and 45: eport. Therefore, leaving blank fie
Page 48 and 49: Beginning an Autotest There are thr
Page 50 and 51: Note: The ping test is a low speed
Page 52 and 53: When there is a cable fault (open o
Page 54 and 55: Figure 5-3 Cable Performance Result
Page 56 and 57: excessive attenuation. Increased at
Page 58 and 59: conductor and shield) is present. A
Page 60 and 61: SIGNALTEK’s active LAN features c
Page 62 and 63: Can SIGNALTEK be damaged by pluggin
Page 65 and 66: 7 Care and Calibration Cleaning Cle
Page 67 and 68: 8 Specifications Cable Types Voice/
Page 69 and 70: 9 Customer Service Technical Assist
Page 71 and 72: IDEAL INDUSTRIES (U.K.) Limited 225
Page 73: Manual Part No. 6510-91-0003 Rev. A

SIGNALTEK Users Guide V1.0 English - Ideal Industries

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?