Heatrae Sadia Electromax Installation Guide - Advanced Water
Heatrae Sadia Electromax Installation Guide - Advanced Water
Heatrae Sadia Electromax Installation Guide - Advanced Water
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
a sealed (pressurized) primary system. It<br />
is suitable for conventional radiator based<br />
<br />
<br />
<br />
sealed system functional and safety controls,<br />
including the circulating pump and primary<br />
expansion vessel. The boiler automatically<br />
responds to lower central heating loads by<br />
reducing (modulating) the boiler output which<br />
saves wasteful on-off cycling. For summer<br />
use the boiler can be switched off on the<br />
<strong>Electromax</strong> control panel, however a “pump<br />
exercise” facility will energise the circulating<br />
pump for a brief period every day to prevent<br />
pump seizure through long periods without<br />
use.<br />
Time and temperature control of the central<br />
heating is by means of a Programmable<br />
Room Thermostat which is supplied loose<br />
with the <strong>Electromax</strong> for remote siting in a<br />
suitable, convenient position.<br />
The necessary cold water mains supply<br />
controls are supplied in a kit for installation<br />
on site in a suitable, convenient position.<br />
<br />
Regulation G3 and <strong>Water</strong> Fittings Regulations<br />
or Byelaws.<br />
1.3 Storage, Unpacking and Handling<br />
The <strong>Electromax</strong> is delivered in protective<br />
expanded polystyrene packaging with<br />
reinforced corner posts. The assembly is<br />
shrunk wrapped in heavy duty polythene. The<br />
<br />
boxed and attached to the main assembly<br />
by 2 polypropylene bands. The assembly<br />
must be stored upright, under cover in dry<br />
conditions.<br />
Units must not be stacked. The packaging<br />
must be removed prior to installation.<br />
Note the weight of the product and the<br />
handling instructions applied to the packaging.<br />
If using a handling device, eg. A sack barrow,<br />
to manually move the <strong>Electromax</strong>, trucking<br />
must be done from the rear to avoid damage<br />
to the outer panels.<br />
The <strong>Electromax</strong> should be lifted and handled<br />
by two persons. Handholds are provided in<br />
the top rear panel, in both side panels and<br />
underneath the <strong>Electromax</strong> assembly to<br />
aid lifting. Stooping should be avoided and<br />
protective clothing worn when necessary.<br />
The packaging is recyclable and should be<br />
disposed of in accordance with environmental<br />
guidelines.<br />
1.4 Contents check list<br />
Within the <strong>Electromax</strong> packaging the following<br />
components are supplied. Please check that<br />
all parts are available before commencing<br />
installation.<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<strong>Electromax</strong> unit<br />
Cold <strong>Water</strong> Combination Valve<br />
comprising Pressure Reducing Valve,<br />
Strainer, Check Valve and Expansion<br />
Valve<br />
Unvented system Expansion Vessel<br />
(18 litre, pre-charged to 3.5 bar)<br />
Wall mounting bracket for Expansion<br />
Vessel<br />
Programmable Room Thermostat<br />
Immersion heater key spanner<br />
Hose connection adaptor for primary<br />
system drain valve<br />
Set of Cable Entry Glands and blanking<br />
plugs (3 x 20mm, 1 x 25.4mm)<br />
<strong>Installation</strong> Manual<br />
User Instructions<br />
Fitting template<br />
4 <strong>Installation</strong> & Servicing Instructions