Distributed / AS-Interface/ Logic Controller ... - Schneider Electric

More documents

Recommendations

Info

Course of Action Optimized AS-Interface M238 Schneider Electric 34
Communication Introduction This chapter describes the data passed via the communications bus that is not bound directly with digital or analog hardware. The list contains: The device links Direction of data flow Symbolic name and Bus address of the device concerned. Device Links This application uses SoMachine protocol on RS485 and AS-Interface busses. The SoMachine protocol connects: Magelis-Panel XBT-GT Modicon M238 Logic controller AS-Interface connects the following devices: 1 M238 on bus address 127 (fixed) 6 TeSysU with ASILUFC5, bus addresses 09 A - 14 A 4 IP20 Input/ Output Modules, bus addresses 15 A - 18 A 4 IP 67 Input/ Output Modules, bus addresses 19 A - 22 A 2 Safety E-Stop switches, bus addresses 02 A and 03 A 2 Door guard switches, bus address 23 A 2 Safety Monitors, bus addresses 01 A and 24 A 4 XALD Pushbuttons, 05 A-08 A AS-Interface Slaves NOTAUS1 NOTAUS2 NOTAUS3 AMPEL Pushbutton1 Symbol NOTAUS1 NOTAUS2 NOTAUS3 uiXVBCred uiXVBCyel uiXVBCgreen uixal2003_1re Application.GVL.xE StpLamp uixal2003_1NO uixal2003_1NC Data Exchange Controller to HMI M238 (Modbus Slave) -> XBTGT (Modbus-Master) Designation E-Stop button, slave address 02A, BYTE NOTAUS1 (from AS-Interface address %IB3) E-Stop button, slave address 03A, BYTE NOTAUS2 (from AS-Interface address %IB4) Door Guard, slave address 23A, BYTE NOTAUS3 (from AS- Interface address %IB23) Harmony Indicator XVBC Slave address 04A, red (from AS-Interface address %QX3.0) Harmony Indicator XVBC Slave address 04A, yellow (from AS-Interface address %QX3.1) Harmony Indicator XVBC Slave address 04A, green (from AS-Interface address %QX3.2) Light of Pushbutton XAL Slave address 05A, red (from AS- Interface address %QX4.1 Light of Pushbutton XAL Slave address 05A, green (from AS- Interface address %QX4.0 Pushbutton XAL Slave address 05A, red (from AS-Interface address %iX6.2 Pushbutton XAL Slave address 05A, red (from AS-Interface address %IX6.3 Optimized AS-Interface M238 Schneider Electric 35
Page 1 and 2: This document is based on European
Page 3 and 4: Important Information NOTICE Read t
Page 5 and 6: CAUTION EQUIPMENT OPERATION HAZARD
Page 7 and 8: Abbreviations Abbreviation AC CB CF
Page 9 and 10: Application Source Code Introductio
Page 11 and 12: System Introduction The system chap
Page 13 and 14: Quantities of Components For a comp
Page 15 and 16: Main Cabinet interior Optimized AS-
Page 17 and 18: Field installation Optimized AS-Int
Page 19 and 20: Hardware Main Switch Compact NSX100
Page 21 and 22: TeSysU Motor Starter Coil Unit TeSy
Page 23 and 24: Modicon M238 Logic controller TM238
Page 25 and 26: Safety Input Slave 1 x 2 inputs ASI
Page 27 and 28: Software General The main programmi
Page 29 and 30: SubD9 to RJ45 cable XBTZ9008 HMI
Page 31 and 32: ASISAFEMON1 programming cable ASISC
Page 33: Implementation Introduction The imp
Page 37 and 38: TeSysU (Control data) TeSysU 1 TeSy
Page 39 and 40: Controller Introduction Requirement
Page 41 and 42: Add Device 1 Right click on the nam
Page 43 and 44: Add AS-Interface devices 1 Right cl
Page 45 and 46: Creating Variables 1 There are two
Page 47 and 48: 4 The upper frame displays the decl
Page 49 and 50: 12 The Input is now displayed in th
Page 51 and 52: 3 Example: In the Add Library --> P
Page 53 and 54: 2 In the Add Object dialog. Select
Page 55 and 56: 2 On the Communication Settings tab
Page 57 and 58: 2 On the Communication Settings tab
Page 59 and 60: 2 In the Save Project As dialog, en
Page 61 and 62: 4 The Vijeo-Designer Runtime Instal
Page 63 and 64: 10 The results of the download to t
Page 65 and 66: 5 If everything is operating normal
Page 67 and 68: 3 POU TeSysU1 shows the control of
Page 69 and 70: 7 POU TeSysU5 shows the control of
Page 71 and 72: 11 POU Variables shows Alarm handli
Page 73 and 74: 3 …and enter the controller name
Page 75 and 76: 5 Open the GVL directory and select
Page 77 and 78: 3 In the Lamp Settings, select the
Page 79 and 80: Create Numeric Display 1 Click on t
Page 81 and 82: 6 The new Numeric Display variable
Page 83 and 84: 4 The “Safety” page shows the s
Page 85 and 86:
10 Return with To Run Mode. Optimiz
Page 87 and 88:
AISSL* Safe Input Slaves 2 E.g. add
Page 89 and 90:
ASI 20MT4I3OSE 5 Use the ASITERACC2
Page 91 and 92:
6 Once you have made the address se
Page 93 and 94:
Starting ASIWIN 1 When the ASIWIN s
Page 95 and 96:
Adding an Emergency- Stop 6 The fol
Page 97 and 98:
Save configuration of Main Monitor
Page 99 and 100:
Available Monitor functions 5 The s
Page 101 and 102:
Selecting the Start Condition 10 On
Page 103 and 104:
2 Before you connect to the monitor
Page 105 and 106:
9 In the top line of the next dialo
Page 107 and 108:
Appendix Detailed Component List Ha
Page 109 and 110:
Software Components Pos. Qty. Descr
Page 111 and 112:
Component Features Components Compa
Page 113 and 114:
SoMachine OEM Machine Programming S
Page 115:
Contact Publisher Process & Machine
show all

Distributed / AS-Interface/ Logic Controller ... - Schneider Electric

Create successful ePaper yourself

Delete template?

Save as template?