Distributed / AS-Interface/ Logic Controller ... - Schneider Electric

More documents

Recommendations

Info

Example screens 1 The Home page shows a picture of the complete architecture. 2 The Bus page shows the AS- Interface state of every device. Green for ready. Red for fault. 3 Page Alarm shows the current alarm state for the TeSysU Optimized AS-Interface M238 Schneider Electric 82
4 The “Safety” page shows the state of the Emergency Stop relay. 5 The TeSys1, TeSys2 and TeSys3 pages are used for parameterization and control of TeSysU motor starters. Each page contains two starters. 6 The OTB page shows the I/O states of the 4 OTB’s installed in the main cabinet. The Inputs and the Outputs are displayed as a Byte. Optimized AS-Interface M238 Schneider Electric 83
Page 1 and 2:
This document is based on European
Page 3 and 4:
Important Information NOTICE Read t
Page 5 and 6:
CAUTION EQUIPMENT OPERATION HAZARD
Page 7 and 8:
Abbreviations Abbreviation AC CB CF
Page 9 and 10:
Application Source Code Introductio
Page 11 and 12:
System Introduction The system chap
Page 13 and 14:
Quantities of Components For a comp
Page 15 and 16:
Main Cabinet interior Optimized AS-
Page 17 and 18:
Field installation Optimized AS-Int
Page 19 and 20:
Hardware Main Switch Compact NSX100
Page 21 and 22:
TeSysU Motor Starter Coil Unit TeSy
Page 23 and 24:
Modicon M238 Logic controller TM238
Page 25 and 26:
Safety Input Slave 1 x 2 inputs ASI
Page 27 and 28:
Software General The main programmi
Page 29 and 30:
SubD9 to RJ45 cable XBTZ9008 HMI
Page 31 and 32: ASISAFEMON1 programming cable ASISC
Page 33 and 34: Implementation Introduction The imp
Page 35 and 36: Communication Introduction This cha
Page 37 and 38: TeSysU (Control data) TeSysU 1 TeSy
Page 39 and 40: Controller Introduction Requirement
Page 41 and 42: Add Device 1 Right click on the nam
Page 43 and 44: Add AS-Interface devices 1 Right cl
Page 45 and 46: Creating Variables 1 There are two
Page 47 and 48: 4 The upper frame displays the decl
Page 49 and 50: 12 The Input is now displayed in th
Page 51 and 52: 3 Example: In the Add Library --> P
Page 53 and 54: 2 In the Add Object dialog. Select
Page 55 and 56: 2 On the Communication Settings tab
Page 57 and 58: 2 On the Communication Settings tab
Page 59 and 60: 2 In the Save Project As dialog, en
Page 61 and 62: 4 The Vijeo-Designer Runtime Instal
Page 63 and 64: 10 The results of the download to t
Page 65 and 66: 5 If everything is operating normal
Page 67 and 68: 3 POU TeSysU1 shows the control of
Page 69 and 70: 7 POU TeSysU5 shows the control of
Page 71 and 72: 11 POU Variables shows Alarm handli
Page 73 and 74: 3 …and enter the controller name
Page 75 and 76: 5 Open the GVL directory and select
Page 77 and 78: 3 In the Lamp Settings, select the
Page 79 and 80: Create Numeric Display 1 Click on t
Page 81: 6 The new Numeric Display variable
Page 85 and 86: 10 Return with To Run Mode. Optimiz
Page 87 and 88: AISSL* Safe Input Slaves 2 E.g. add
Page 89 and 90: ASI 20MT4I3OSE 5 Use the ASITERACC2
Page 91 and 92: 6 Once you have made the address se
Page 93 and 94: Starting ASIWIN 1 When the ASIWIN s
Page 95 and 96: Adding an Emergency- Stop 6 The fol
Page 97 and 98: Save configuration of Main Monitor
Page 99 and 100: Available Monitor functions 5 The s
Page 101 and 102: Selecting the Start Condition 10 On
Page 103 and 104: 2 Before you connect to the monitor
Page 105 and 106: 9 In the top line of the next dialo
Page 107 and 108: Appendix Detailed Component List Ha
Page 109 and 110: Software Components Pos. Qty. Descr
Page 111 and 112: Component Features Components Compa
Page 113 and 114: SoMachine OEM Machine Programming S
Page 115: Contact Publisher Process & Machine
show all

Distributed / AS-Interface/ Logic Controller ... - Schneider Electric

Create successful ePaper yourself

Delete template?

Save as template?