Distributed / AS-Interface/ Logic Controller ... - Schneider Electric

More documents

Recommendations

Info

M238 AS- Interface Master module TWDNOI10M ASILUFC5 ASI20M* 3 The M238 AS-Interface Master module use Auto addressing mode (in SoMachine parameterized) In order for slave addressing to be successful, the nodes must be connected to the power supply via the yellow AS- Interface cable. Before you start addressing, switch the master ‘offline’ by pressing and holding down the PB2 button on the AS-Interface master module for 3 – 4 seconds. The master will switch to offline mode and will indicate this on the module via an LED lighting up red next to the word OFF. 4 Use the XZMG12 adapter cable to address ASI20M* and ASILUFC5 IP20 devices (TeSysU motor starters communication cassette)). Connect the adapter to the node via the yellow plug. On slaves requiring a 24 V auxiliary supply (black AS- Interface cable) at output level (e.g., as is the case with TeSysU), the power supply must be connected when the nodes are programmed. M12 male with yellow and green plug-in connectors Optimized AS-Interface M238 Schneider Electric 88
ASI 20MT4I3OSE 5 Use the ASITERACC2 adapter cable to address IP20 field devices. Connect the adapter to the M12 female AS-Interface AUX on the right underside of the device. ASI67FMP43E 6 Use the ASITERACC1F adapter cable to address IP67 field devices. Connect the adapter to the M12 female AS-Interface AUX on the right underside of the device. Optimized AS-Interface M238 Schneider Electric 89
Page 1 and 2:
This document is based on European
Page 3 and 4:
Important Information NOTICE Read t
Page 5 and 6:
CAUTION EQUIPMENT OPERATION HAZARD
Page 7 and 8:
Abbreviations Abbreviation AC CB CF
Page 9 and 10:
Application Source Code Introductio
Page 11 and 12:
System Introduction The system chap
Page 13 and 14:
Quantities of Components For a comp
Page 15 and 16:
Main Cabinet interior Optimized AS-
Page 17 and 18:
Field installation Optimized AS-Int
Page 19 and 20:
Hardware Main Switch Compact NSX100
Page 21 and 22:
TeSysU Motor Starter Coil Unit TeSy
Page 23 and 24:
Modicon M238 Logic controller TM238
Page 25 and 26:
Safety Input Slave 1 x 2 inputs ASI
Page 27 and 28:
Software General The main programmi
Page 29 and 30:
SubD9 to RJ45 cable XBTZ9008 HMI
Page 31 and 32:
ASISAFEMON1 programming cable ASISC
Page 33 and 34:
Implementation Introduction The imp
Page 35 and 36:
Communication Introduction This cha
Page 37 and 38: TeSysU (Control data) TeSysU 1 TeSy
Page 39 and 40: Controller Introduction Requirement
Page 41 and 42: Add Device 1 Right click on the nam
Page 43 and 44: Add AS-Interface devices 1 Right cl
Page 45 and 46: Creating Variables 1 There are two
Page 47 and 48: 4 The upper frame displays the decl
Page 49 and 50: 12 The Input is now displayed in th
Page 51 and 52: 3 Example: In the Add Library --> P
Page 53 and 54: 2 In the Add Object dialog. Select
Page 55 and 56: 2 On the Communication Settings tab
Page 57 and 58: 2 On the Communication Settings tab
Page 59 and 60: 2 In the Save Project As dialog, en
Page 61 and 62: 4 The Vijeo-Designer Runtime Instal
Page 63 and 64: 10 The results of the download to t
Page 65 and 66: 5 If everything is operating normal
Page 67 and 68: 3 POU TeSysU1 shows the control of
Page 69 and 70: 7 POU TeSysU5 shows the control of
Page 71 and 72: 11 POU Variables shows Alarm handli
Page 73 and 74: 3 …and enter the controller name
Page 75 and 76: 5 Open the GVL directory and select
Page 77 and 78: 3 In the Lamp Settings, select the
Page 79 and 80: Create Numeric Display 1 Click on t
Page 81 and 82: 6 The new Numeric Display variable
Page 83 and 84: 4 The “Safety” page shows the s
Page 85 and 86: 10 Return with To Run Mode. Optimiz
Page 87: AISSL* Safe Input Slaves 2 E.g. add
Page 91 and 92: 6 Once you have made the address se
Page 93 and 94: Starting ASIWIN 1 When the ASIWIN s
Page 95 and 96: Adding an Emergency- Stop 6 The fol
Page 97 and 98: Save configuration of Main Monitor
Page 99 and 100: Available Monitor functions 5 The s
Page 101 and 102: Selecting the Start Condition 10 On
Page 103 and 104: 2 Before you connect to the monitor
Page 105 and 106: 9 In the top line of the next dialo
Page 107 and 108: Appendix Detailed Component List Ha
Page 109 and 110: Software Components Pos. Qty. Descr
Page 111 and 112: Component Features Components Compa
Page 113 and 114: SoMachine OEM Machine Programming S
Page 115: Contact Publisher Process & Machine
show all

Distributed / AS-Interface/ Logic Controller ... - Schneider Electric

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?