TH-V70R[B] revision - JVC

Operating other manufacturers’ VCR
By changing the remote control signals from preset ones to the other manufacturers’, you can use the remote control supplied
for this system to operate other manufacturers’ VCRs.
• You can also operate other manufacturers’ TVs using the remote control supplied with this system. (See page 20.)
• When operating other manufacturers’ VCR, aim the remote control directly at the remote control sensor on your VCR.
Refer also to the instruction manuals supplied with your VCR.
AUX
AUDIO
TV VOL
1
DOWN
/REW
FM/AM
ANGLE
CHANNEL
TV/VIDEO
PLAY
TUNING
DVD VCR1
SUBTITLE
MUTING
DECODE
RETURN DIGEST ZOOM VFP
TOP MENU MENU ZOOM
CONTROL – SUBWOOFER + EFFECT
1 2 3
VCR
– CENTER + TEST
4 5 6
TV
– REAR-L +
SLEEP
7 8 9
– REAR-R +
SETTING
10 0 +10
ON
SCREEN
PTY(
CHOICE
RDS DISPLAY
TV RETURN FM MODE
TA/NEWS/INFO
ENTER
TV
+
–
PTY SEARCH
RDS
PTY9
SURROUND
MODE
VOLUME
FF/
AUDIO
SOUND
100+
¡
UP
DVD
VCR
button
Number buttons
VCR CONTROL
button
Remote control
mode selector
CHANNEL +/–
buttons
¡ button
1 button
PLAY button
7 Setting the remote control signal for operating your
VCR.
• You can operate your VCR without setting the remote control signal if your VCR
is a JVC VCR.
1 Slide the remote control mode selector to ”DVD.”
2 Press and hold VCR .
Keep it pressed until step 4 is finished.
3 Press VCR CONTROL.
4 Press Number buttons (1-9, 0) to enter a manufacturer’s code
(2 digit).
See the list below to find the code.
Examples: For a Philips VCR, press 0, then 5.
For a Panasonic VCR, press 2, then 1.
5 Release VCR .
6 Try to operate your VCR by pressing VCR .
When your VCR turns on or off, you have entered the correct code.
If there are more than one cord listed for your brand of VCR, try each one
until you enter the correct one.
REC
MEMORY
STOP
PAUSE
STROBE
DIMMER
RM–STHV70R
DVD CINEMA SYSTEM
PAUSE button
STOP button
÷ REC button
7 To operate your VCR
You can use the following buttons for operating your VCR:
VCR : Turns on and off the VCR.
• After pressing VCR CONTROL, you can use the following buttons for operating
your VCR:
PLAY:
Starts playback.
STOP:
Stops operation.
PAUSE:
Pauses playback.
¡: Fast forwards a video tape.
1: Rewinds a video tape.
÷ REC: Press this button together with PLAY to start recording.
Press this button together with PAUSE to pause
recording.
CHANNEL +/–: Changes the TV channels on the VCR.
Manufacturers’ codes for VCR
Manufacturer Code
JVC 01
Aiwa 02, 20
Bell+Howell 03, 16
Blaupunkt 04
CGM 03, 05, 16
Daewoo 34
Digtal 05
Fisher 03, 16
G.E. 06
Grundig 07
Hitachi 08, 09
Loewe 05, 10, 11
Magnavox 04, 05
Mitsubishi 12 – 15
71
Manufacturer Code
Nokia 16
Nordmende 17 – 19, 31
Orion 20
Panasonic 21
Philips 05, 22
Phonola 05
Saba 17 – 19, 23, 31
Samsung 24, 25
Sanyo 03, 16
Sharp 26, 27
Siemens 07
Sony 28 – 30, 35
Telefunken 17 – 19, 31, 32
Toshiba 33
* Manufacturers’ codes
are subject to change
without notice. If they
are changed, this
remote control cannot
operate the
equipment.