Solution 4+4 Installation Manual - Securityhelpdesk.com.au

More documents

Recommendations

Info

16 Solution 4+4 Installation Manual Quick Start The following steps will enable you to use the Solution 4+4 control panel with the factory default values. The default values allow the control panel to communicate in the Contact ID format. 1. Connect the AC plug pack to the control panel. 2. Check the operation of the red overload indicator (LD1) on the PCB. In normal operation the indicator will not illuminate. The MAINS indicator will remain on as will the AWAY indicator. The system is now in the armed state. 3. Enter the default Master Code 2580 followed by the button. The AWAY indicator will extinguish. The system is now in the disarmed state. Installer’s Programming Mode can now be accessed. 4. The back-up battery should now be connected. 5. Enter the factory default Installer Code 1234 followed by the button. The STAY and AWAY indicators will now flash simultaneously to indicate that you have now entered Installer’s Programming Mode. 6. Enter the Primary Telephone Number followed by the Secondary Telephone Number and the Subscriber ID Number. 7. Set the time for the test reports if required. Any other programming changes required may also be made, otherwise the factory default settings will be used. 8. Enter Installer’s Command 960 followed by the button to exit Installer’s Programming Mode. The system will now return to the disarmed state and is now ready for use. Refer to “Installer’s Programming Commands” on page 22 for more information 9. Use the Master Code to set the date and time. How To Set The New Date and Time 1. Enter your followed by 6 and the button. Three beeps will be heard and the STAY and AWAY indicators will begin to flash. 2. Enter the day, month, year, hour and minute using the (DD, MM, YY, HH, MM) format. 3. Press the button when finished. Two beeps will be heard and the STAY and AWAY indicators will extinguish. Zone Defaults The default zone settings are as listed in the table below. Zone No Zone Type 1 Delay-1 2 & 3 Handover 4 24 Hour Zone Table 1: Zone Defaults ISSUE123.DOC Electronics Design and Manufacturing Pty Limited
Programming This section includes the following; • Programming • Programming With The Remote Codepad • Programming With The Hand Held Programmer • Programming With The Programming Key • Programming Option Bits • Installer’s Programming Commands • Disable Factory Default • Defaulting The Control Panel
Page 1: Solution 4+4 Installation Manual IS
Page 5: Solution 4+4 Installation Manual Co
Page 8 and 9: System Operations _________________
Page 10 and 11: Zone Information___________________
Page 12 and 13: System Options 2___________________
Page 14 and 15: 14 Solution 4+4 Installation Manual
Page 66 and 67:
66 Solution 4+4 Installation Manual
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
100 Solution 4+4 Installation Manua
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
show all

Solution 4+4 Installation Manual - Securityhelpdesk.com.au

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?