Solution 4+4 Installation Manual - Securityhelpdesk.com.au

More documents

Recommendations

Info

28 Solution 4+4 Installation Manual Command 966 - Enable/Disable Automatic Stepping Of Locations This command enables or disables the automatic stepping of locations while programming. When enabled via the hand held programmer, the decimal point of the left most display will reflect the mode of operation. If the decimal point is illuminated then auto step mode is active. An automatic increment of the location being programmed will occur as soon as the * button is pressed positioning you at the next location ready for programming. If the decimal point is not illuminated, the auto step mode is disabled. The next programming location will need to be manually selected by pressing the # button. As you can see from the examples below, auto step mode is a very useful feature when programming successive locations. How To Enable Automatic Stepping Of Locations 1. Enter Installer’s Programming Mode. (ie. 1234 followed by the # button). 2. Enter command 966 followed by the # button. Two beeps will be heard. How To Disable Automatic Stepping Of Locations Example 1. Enter command 966 followed by the # button. Two beeps will be heard. (Auto Step Enabled) To enter the Primary Telephone Number "02 pause 9672 1055" with auto step enabled (ie. Decimal point illuminated). Press 0 followed by the # button. (This will position you at "LOCATION 000" being the start of the Primary Telephone Number). Example + * + 2 + * + + * + 9 + * + 6 + * + 7 + * + 2 + * + 1 + * + + * + 5 + * + 5 + * + 0 + * (Auto Step Disabled) To enter the Primary Telephone Number "02 pause 9672 1055" with auto step disabled (ie. Decimal point extinguished). Press 0 followed by the # button. (This will position you at "LOCATION 000" being the start of the Primary Telephone Number). + * + # + 2 + * + # + + * + # + 9 + * + # + 6 + * + # + 7 + * + # + 2 + * + # + 1 + * + # + + * + # + 5 + * + # + 5 + * + # + 0 + * ISSUE123.DOC Electronics Design and Manufacturing Pty Limited
Programming 29 Command 999 - Display Software Version Number This command will display the control panel's software version number. This command can only be used with the hand held programmer. Once access to Installer’s Programming Mode has been gained, enter command 999 followed by the # button to display the control panel's software version number. Two beeps will be heard. Press the # button to exit this command and return to the Installer’s Programming Mode. Disable Factory Default LOCATION 900 0 The system has a feature that prevents the control panel from being manually defaulted via the default button or by using a programming key unless the Installer’s Code is known. Any number between 0-14 programmed into this location will allow defaulting of the control panel. If 15 has been programmed into this location, defaulting of the control panel will not operate and the Installer Code MUST be used for further programming of the control panel. If the Installer Code is not known, the control panel will need to be returned to your EDM Distributor for exchange. A nominal fee applies for this service. Electronics Design and Manufacturing Pty Limited does not recommend the use of this feature. If the option to prevent defaulting of the control panel is required, a special programming procedure has been introduced to eliminate any possibility of accidentally setting this option. The default button on the PCB must be held down while programming this location. How To Prevent Manual Defaulting Of The Control Panel 1. Disarm the system. 2. Access Installer's Programming Mode. 3. Go to "LOCATION 900". 4. Hold down the default button. 5. Program a 15 into "LOCATION 900". 6. Release the default button. 7. Exit Installer's Programming Mode. Electronics Design and Manufacturing Pty Limited ISSUE123.DOC
Page 1: Solution 4+4 Installation Manual IS
Page 5: Solution 4+4 Installation Manual Co
Page 8 and 9: System Operations _________________
Page 10 and 11: Zone Information___________________
Page 12 and 13: System Options 2___________________
Page 14 and 15: 14 Solution 4+4 Installation Manual
Page 78 and 79:
78 Solution 4+4 Installation Manual
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
100 Solution 4+4 Installation Manua
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
show all

Solution 4+4 Installation Manual - Securityhelpdesk.com.au

Create successful ePaper yourself

Delete template?

Save as template?