Owner's Manual Cadillac BLS - IFS Europe BV
Owner's Manual Cadillac BLS - IFS Europe BV
Owner's Manual Cadillac BLS - IFS Europe BV
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
460_OM_MY09.book Page 74 Wednesday, April 2, 2008 10:32 AM<br />
74 Instruments and controls<br />
Speed warning<br />
This value is preset to 55 mph (90 km/h).<br />
The value can be set to between<br />
0 and 150 mph (0–250 km/h).<br />
On some markets, the value is locked<br />
at 120 km/h and cannot be changed.<br />
1Select SPD W using the steering wheel<br />
buttons, or .<br />
2 Hold the SET button depressed until<br />
a chime sounds.<br />
3 Select speed using the steering wheel<br />
buttons, or .<br />
4 End by pressing the SET button.<br />
The word ON on the right-hand side of the<br />
display indicates when the speed warning<br />
function is active.<br />
An audible alarm will sound if the set speed<br />
is exceeded.<br />
Disengage the function with the CLR button.<br />
Re-engage the function using the SET<br />
button.<br />
Calculating the arrival time<br />
(When will I arrive if I know how far I have to<br />
drive?)<br />
This function should be used before starting<br />
out a journey.<br />
To calculate the arrival time, the distance<br />
must first be given.<br />
1Select Dist using the steering wheel<br />
buttons, or .<br />
2 Hold the SET button depressed until a<br />
chime sounds.<br />
1 Set how long it takes to get to the destination<br />
using the steering wheel buttons,<br />
or .<br />
2 End by pressing the SET button.<br />
The estimated arrival time is displayed on<br />
the right-hand side of the display.<br />
If you take a break, this time is added to the<br />
estimated arrival time.<br />
During the trip, you can select Dist to display<br />
the estimated arrival time as well as<br />
how much longer you have to drive.<br />
After the distance to destination has<br />
decreased to zero, Dist will function as a trip<br />
meter (seeUsing DIST as a trip meter). The<br />
starting value for the trip meter will be the<br />
last distance set for the Dist function.<br />
Example: The Dist function is set to 100 km.<br />
After the count-down has reached 0 km,<br />
Dist will act as a trip meter beginning<br />
at 100 km.<br />
Calculating the arrival time if a specified<br />
average speed is maintained<br />
(When will I arrive if I know how far I have<br />
to drive and know what my average speed<br />
will be?)<br />
This function should be used before starting<br />
out a journey.<br />
First, set the distance under Dist.<br />
1 Then select the Speed Ø function using<br />
the steering wheel buttons, or .<br />
2 Hold the SET button depressed until a<br />
chime sounds.<br />
3 Set an estimated average speed using<br />
the steering wheel buttons, or .<br />
4 End by pressing the SET button.<br />
The time of arrival is updated during the<br />
journey based on the average speed since<br />
Dist was set. The speed of the car must<br />
exceed 12 mph (20 km/h).<br />
By selecting Dist during the journey, you<br />
can see how far is left.<br />
When Dist reaches zero Dist acts as a trip<br />
meter. The trip meter starts from the distance<br />
that was set previously.