25.07.2014 Views

User's Manual 686LCD/S & 686LCD/MG CPU Board

User's Manual 686LCD/S & 686LCD/MG CPU Board

User's Manual 686LCD/S & 686LCD/MG CPU Board

SHOW MORE
SHOW LESS

Create successful ePaper yourself

Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.

I/O Port Access Read/<br />

Write<br />

<strong>686LCD</strong>/S & <strong>686LCD</strong>/<strong>MG</strong> <strong>CPU</strong> <strong>Board</strong> - Version 1.4.0 - 8. December 1997<br />

Description<br />

01F0h - 01F7h may be used by on-board hard disk controller for primary (1) IDE port.<br />

Depends on choice made in INSIDE setup.<br />

01F0h PCI/ISA R/W Hard disk 0 data register base port<br />

01F1h PCI/ISA R Hard disk 0 error register<br />

Bits 7-3<br />

Bits 2-0<br />

Bit 7<br />

Bit 6<br />

Bit 5<br />

Bit 4<br />

Bit 3<br />

Bit 2<br />

Bit 1<br />

Bit 0<br />

-<br />

-<br />

001<br />

010<br />

011<br />

100<br />

101<br />

0<br />

1<br />

0<br />

1<br />

-<br />

0<br />

1<br />

-<br />

0<br />

1<br />

0<br />

1<br />

0<br />

1<br />

Diagnostic mode<br />

Reserved<br />

Diagnostics mode errors<br />

No errors<br />

Controller error<br />

Sector buffer error<br />

ECC device error<br />

Control processor error<br />

Operation mode<br />

Block is not bad<br />

Bad block detected<br />

No error<br />

Uncorrectable ECC error<br />

Reserved<br />

ID not found<br />

ID found<br />

Reserved<br />

Command aborted<br />

Command completed<br />

Track 000 found<br />

Track 000 not found<br />

DAM found (CP-3002 is always 0)<br />

DAM not found<br />

01F1h PCI/ISA W Hard disk 0 write pre-compensations register<br />

01F2h PCI/ISA R/W Hard disk 0 sector count<br />

01F3h PCI/ISA R/W Hard disk 0 sector number<br />

01F4h PCI/ISA R/W Hard disk 0 number of cylinders, low byte<br />

01F5h PCI/ISA R/W Hard disk 0 number of cylinders, high byte<br />

01F6h PCI/ISA R/W Hard disk 0 drive/head register<br />

Bit 7<br />

Bit 6<br />

Bit 5<br />

Bit 4<br />

1<br />

0<br />

1<br />

-<br />

0<br />

1<br />

Bit 3-0 nnnn<br />

01F7h PCI/ISA R Hard disk 0 status register<br />

Bit 7<br />

Bit 6<br />

Bit 5<br />

Bit 4<br />

Bit 3<br />

Bit 2<br />

Bit 1<br />

Bit 0<br />

1<br />

1<br />

1<br />

1<br />

1<br />

1<br />

1<br />

1<br />

Reserved<br />

Reserved<br />

Reserved<br />

Drive select<br />

First hard disk drive<br />

Second hard disk drive<br />

Head select bits<br />

01F7h PCI/ISA W Hard disk drive 0 command register<br />

Controller is executing a command<br />

Drive is ready<br />

Write fault<br />

Seek complete<br />

Sector buffer requires servicing<br />

Disk data read corrected<br />

An index. Set to 1 each disk revolution<br />

Previous command ended with an error<br />

020Ch - 020Dh and 021Fh are used by AMIBIOS.<br />

020Ch-<br />

R/W Reserved for special use by AMIBIOS<br />

020Dh<br />

021Fh R/W Reserved for special use by AMIBIOS<br />

0278h - 027Fh may be used by on-board peripheral controller as Parallel port 2.<br />

Depends on choice made in INSIDE setup.<br />

The bit definitions for these addresses are the same as those for addresses 0378h-037Fh.<br />

0278h PCI/ISA R/W Parallel port 2, data<br />

0279h PCI/ISA R/W Parallel port 2, status<br />

027Ah PCI/ISA R/W Parallel port 2, control<br />

027Bh PCI/ISA R/W Parallel port 2, EPP address port<br />

027Ch PCI/ISA R/W Parallel port 2, EPP data port 0<br />

027Dh PCI/ISA R/W Parallel port 2, EPP data port 1<br />

027Eh PCI/ISA R/W Parallel port 2, EPP data port 2<br />

027Fh PCI/ISA R/W Parallel port 2, EPP data port 3<br />

INSIDE Technology A/S. Page 40 of 134

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!