Untitled - Standartizacijos departamentas prie AM

LIETUVOS STANDARTIZACIJOS DEPARTAMENTO BIULETENIS 2008 Nr. 07
TC 27 ISO 540:2008
Hard coal and coke - Determination of ash fusibility
TC 29 ISO 6752:2008
Tools for pressing - Round punches with 60 degrees
conical head and straight shank
TC 34 ISO 6668:2008
Green coffee - Preparation of samples for use in
sensory analysis
TC 34 ISO 8534:2008
Animal and vegetable fats and oils - Determination of
water content - Karl Fischer method (pyridine free)
TC 39 ISO 8525:2008
Airborne noise emitted by machine tools - Operating
conditions for metal-cutting machines
TC 41 ISO 5293:2004/Cor 1:2008
Conveyor belts - Determination of minimum transition
distance on three idler rollers - Technical
Corrigendum 1
TC 43 ISO 3382-2:2008
Acoustics - Measurement of room acoustic
parameters - Part 2: Reverberation time in ordinary
rooms
TC 44 ISO 24034:2005/Amd 1:2008
Welding consumables - Solid wires and rods for fusion
welding of titanium and titanium alloys - Classification -
Amendment 1: .
TC 44 ISO 3581:2003/Cor 1:2008
Welding consumables - Covered electrodes for
manual metal arc welding of stainless and heatresisting
steels - Classification - Technical
Corrigendum 1
TC 45 ISO 16565:2008
Rubber - Determination of 5-ethylidenenorbornene
(ENB) or dicyclopentadiene (DCPD) in ethylenepropylene-diene
(EPDM) terpolymers
TC 46 ISO/TR 26122:2008
Information and documentation - Work process
analysis for records
TC 51 ISO 12776:2008
Pallets - Slip sheets
TC 59 ISO 15686-5:2008
Buildings and constructed assets - Service-life
planning - Part 5: Life-cycle costing
TC 59 ISO 15686-8:2008
Buildings and constructed assets - Service-life
planning - Part 8: Reference service life and servicelife
estimation
TC 60 ISO 6336-1:2006/Cor 1:2008
Calculation of load capacity of spur and helical gears -
Part 1: Basic principles, introduction and general
influence factors - Technical Corrigendum 1
TC 60 ISO 6336-2:2006/Cor 1:2008
Calculation of load capacity of spur and helical gears -
Part 2: Calculation of surface durability (pitting) -
Technical Corrigendum 1
TC 60 ISO 6336-3:2006/Cor 1:2008
Calculation of load capacity of spur and helical gears -
Part 3: Calculation of tooth bending strength - Technical
Corrigendum 1
TC 61 ISO 6721-2:2008
Plastics - Determination of dynamic mechanical
properties - Part 2: Torsion-pendulum method
TC 61 ISO 10840:2008
Plastics - Guidance for the use of standard fire tests
TC 61 ISO 11357-6:2008
Plastics - Differential scanning calorimetry (DSC) -
Part 6: Determination of oxidation induction time
(isothermal OIT) and oxidation induction temperature
(dynamic OIT)
TC 61 ISO 15106-4:2008
Plastics - Film and sheeting - Determination of water
vapour transmission rate - Part 4: Gaschromatographic
detection sensor method
TC 61 ISO 15270:2008
Plastics - Guidelines for the recovery and recycling of
plastics waste
TC 67 ISO 10416:2008
Petroleum and natural gas industries - Drilling fluids -
Laboratory testing
TC 67 ISO 13628-11:2007/Cor 1:2008
Petroleum and natural gas industries - Design and
operation of subsea production systems - Part 11:
Flexible pipe systems for subsea and marine
applications - Technical Corrigendum 1
TC 67 ISO 13704:2007/Cor 1:2008
Petroleum, petrochemical and natural gas industries -
Calculation of heater-tube thickness in petroleum
refineries - Technical Corrigendum 1
TC 67 ISO 28300:2008
Petroleum, petrochemical and natural gas industries -
Venting of atmospheric and low-pressure storage
tanks
TC 70 ISO 8178-4:2007
Reciprocating internal combustion engines - Exhaust
emission measurement - Part 4: Steady-state test
cycles for different engine applications
TC 71 ISO 19338:2007/Cor 1:2008
Performance and assessment requirements for design
standards on structural concrete - Technical
Corrigendum 1
TC 98 ISO 13823:2008
General principles on the design of structures for
durability
TC 100 ISO 10190:2008
Motorcycle chains - Characteristics and test methods
TC 106 ISO 3823-2:2003/Amd 1:2008
Dentistry - Rotary bur instruments - Part 2: Finishing
burs – Amendment 1
TC 108 ISO 18431-2:2004/Cor 1:2008
Mechanical vibration and shock - Signal processing -
Part 2: Time domain windows for Fourier Transform
analysis - Technical Corrigendum 1
TC 110 ISO 22915-8:2008
Industrial trucks - Verification of stability - Part 8:
Additional stability test for trucks operating in the
special condition of stacking with mast tilted forward
and load elevated
TC 110 ISO 22915-10:2008
Industrial trucks - Verification of stability - Part 10:
Additional stability test for trucks operating in the
special condition of stacking with load laterally
displaced by powered devices
TC 110 ISO 22915-20:2008
Industrial trucks - Verification of stability - Part 20:
Additional stability test for trucks operating in the
special condition of offset load, offset by utilization
TC 117 ISO 5801:2007/Cor 1:2008
Industrial fans - Performance testing using
standardized airways - Technical Corrigendum 1
TC 119 ISO 4490:2008
Metallic powders - Determination of flow rate by means
of a calibrated funnel (Hall flowmeter)
TC 119 ISO 17352:2008
Hardmetals - Determination of silicon in cobalt metal
powders using graphite-furnace atomic absorption
TC 121 ISO 5359:2008
Low-pressure hose assemblies for use with medical
gases
17