Impala SS and Caprice T56 Six Speed install guide - GRAIL

More documents

Recommendations

Info

6. These connectors will attach to the clutch anticipate and brake cruise release switches they will look like this. 7. Connect harness assembly to switches and you are ready to go. If the harness that you have from the donor car is listed on Fbody harness assemblies diagram as &L36&M49&K34 on the top right of the figure. You are going to do the following. 1. Purchase plug pigtail assembly part number PT159 or GM number 12101888 as pictured here. 54
2. Locate wiring on the Caprice or Impala that is going to the current brake pedal switch. I will be a two pin connector with a brown/white wire going in pin B and a brown wire going in pin A 3. Cut connector off and discard 4. Splice wiring to new pigtail assembly as follows ‣ Brown/White wire to wire color coming from pin B on new pigtail assembly ‣ Brown wire to wire color coming from pin A on new pigtail 5. Now the harness that you have from the Fbody donor is from a V6 model. The switches are not identical for the brake and the clutch release, due to space constraints you are going to have to modify this harness to make it almost identical to the MM6 version harness as previously discussed. 6. For this Fbody model harness you are going to have to get another pigtail connector and another release switch identical to the one that you have on the brake pedal. 7. The pigtail you are going to need is part number PT733 or GM number 12126463 as pictured here. 55
Page 1 and 2:
Impala SS and Caprice T56 Six Speed
Page 3 and 4: Here we go First you are going to n
Page 5 and 6: 2. The F2B clutch pedal bracket kit
Page 7 and 8: As listed above the original cover
Page 9 and 10: 2. Take measurement from yoke, at t
Page 11 and 12: 15. Take the old transmission dipst
Page 13 and 14: 23. Remove door sill plates that ar
Page 15 and 16: acket overlaps the black mounting p
Page 17 and 18: The next picture shows where to cut
Page 19 and 20: 30. Next remove the two existing br
Page 21 and 22: wiring to mine and put it behind wh
Page 23 and 24: 41. Install retaining clip on rod o
Page 25 and 26: 46. Now to the bump out that you ar
Page 27 and 28: Towards engine Not all manufacturer
Page 29 and 30: marks up. (Note: most times balance
Page 31 and 32: 59. It is my recommendation that yo
Page 33 and 34: 66. Now route in the wiring that yo
Page 35 and 36: 77. Next install shifter onto shift
Page 37 and 38: 87. The last step is to have you PC
Page 39 and 40: Special Thanks A special thanks nee
Page 41 and 42: 2. IT will be like a jigsaw puzzle
Page 43 and 44: Impala SS and Caprice T56 Six Speed
Page 45 and 46: F2B bracket template to use for cut
Page 47 and 48: Impala and Caprice Brake Pedal and
Page 49 and 50: Fbody Clutch and Brake Pedal assemb
Page 51 and 52: Fbody wiring diagram sheet 2 51
Page 53: If the harness that you have from t
Page 57 and 58: Most times the pedal assembly from
Page 59 and 60: 4. Splice wiring to new pigtail ass
Page 61: 8. Attach harness assembly to switc
show all

Impala SS and Caprice T56 Six Speed install guide - GRAIL

Create successful ePaper yourself

Delete template?

Save as template?