CUTTING TOOLS

19 265 PCLN 95° toolholder
for internal machining, with lever lock “P”
1
CUTTING TOOLS
19 265 030
Toolholder 19 265… 19 265... D h h1 L1 L2 f Ø min. Tip
Type right-hand left-hand mm mm mm mm mm mm mm
S 16 R PCLN R/L 09* 005 006 16 15 7.5 200 26 11 20 CNMG 0903…
S 20 S PCLN R/L 09* 010 011 20 18 9.0 250 29 13 25 CNMG 0903…
S 25 T PCLN R/L 09 015 016 25 23 11.5 300 33 17 32 CNMG 0903…
S 25 T PCLN R/L 12* 020 021 25 23 11.5 300 40 17 31 CNMG 1204…
S 32 U PCLN R/L 12 025 026 32 30 15.0 350 50 22 39 CNMG 1204…
S 40 V PCLN R/L 12 030 031 40 37 18.5 400 60 27 48 CNMG 1204…
S 50 W PCLN R/L 12 032 034 50 47 23.5 450 65 27 61 CNMG 1204…
* = Toolholder without shim / on request with internal cooling
Accessories for 19 207…, 19 208…, 19 213…, 19 265…
For toolholder Lever lock “P” Clamping screw Key Shim Wedge Mandrel
Type 19 942… 19 934… 19 950… 19 943… 19 947… 19 930…
PC 09 002 004 006 009 001 001
PC 12 003 005 002 006 003 002
PC 16 005 008 002 007 004 003
PC 19 006 006 003 008 006 004
S 16/20 PC 09 001 003 001 - - -
S 25 PC 09 002 009 006 009 001 001
S 25 PC 12 014 009 006 - - -
S 32 PC 12 017 011 002 006 003 002
19 359 CNMG - WM tip
medium machining
ap = 1.0 - 5.0 mm
Type 19 359… 19 359… 19 359…
WOG 2315 WOG 2025 WOG 2435
CNMG 090304 - WM - 054 045
CNMG 090308 - WM - 074 065
CNMG 120404 - WM 013 007 008
CNMG 120408 - WM 023 014 005
CNMG 120412 - WM 033 034 025
P 120 - 270 100 - 230 80 - 190 0.05 - 0.4
M - - 80 - 180 0.05 - 0.4
K 100 - 220 - - 0.05 - 0.4
NE - - - -
H - - - -
S
“Turning” / “Parting” / “Milling”
280
19 361 CNMG - 909 tip
roughing, double-sided
ap = 2.0 - 5.0 mm
Type 19 361… 19 361… 19 361…
WOG 2315 WOG 2025 WOG 2435
CNMG 120408 - 909 023 014 005
CNMG 160612 - 909 063 054 065
P 120 - 270 100 - 230 80 - 190 0.25 - 0.8
M - - 80 - 180 0.25 - 0.8
K 100 - 220 - - 0.25 - 0.8
NE - - - -
H - - - -
S
ibemo Kazakhstan - 090301 Republic of Kazakhstan, West Kazakhstan Oblast, Aksai, Pramzone, BKKS office complex
Phone: +7 71133 93077 ; Fax: +7 71133 93074 ; E-Mail: info@ibemo-kz.com
“TOOLS”