Owner's Manual - Faria Instruments

More documents

Recommendations

Info

Displays Gear Temp on diesel engines. Engine Hours Displays the engine hours data received from the engine ECU. Volts Displays system voltage from ECU. Default Screen “5” Default Screen “4” Water Press or Oil Pressure or Oil Temp Displays water pressure on outboards, and Jet drives. Displays Oil Pressure on inboards, inboard/outboards and diesels. Displays Oil Temp an Verado Outboards. Speed Displays boat speed as received from the SmartCraft bus. For improved accuracy at all speeds, the SmartCraft system allows the use of both a pitot tube speed input (the default) and a paddle wheel input. If the paddle wheel option is installed, the SmartCraft system uses the paddle wheel at low speeds and the pitot tube at high speeds. The point at which the change from paddle wheel to pitot occurs is called the “Transition Point”. The user can adjust the “Transition Point” in the “Edit” mode “Configure Speed” function. Adjust the “Set Sender Transition” as described in the “Edit” mode function to obtain the best performance of this function. Sea Temp or Fuel Level Displays sea temperature as received from the SmartCraft bus on all engines except Jet Drive. Displays Fuel Level on Jet Drives. Page 7 RPM Displays engine RPM as received from the SmartCraft bus. Oil Level or Oil Pressure or Water Pressure or Intake Manifold Temp. Displays oil level on two cycle outboards, and jet drives, oil pressure on inboards, inboard/outboard, and Verado outboards. Displays Water Pressure on 4 cycle outboards. Displays Intake Manifold Temperature on diesels engines. RPM Sync or Engine Hours Displays a graphic display showing engine sync in dual engine installations. Center mark appears if engines are synchronized. Displays Engine Hours on single engine installations. Default Screen “6” Speed or Steering Angle Displays Speed for 2 cycle and 4 cycle outboards, Jet drives, and Verado outboards. Displays Steering Angle on inboard/outboards, inboards and diesel engines. RPM or Trim Sync Displays RPM for all single engine installations and Trim Sync for all dual engine installations.
Fuel Level Displays a graphic display of 8 boxes for all engine types. All boxes filled in indicates a full level. Default Screen “7” Tank2 Level Displays a graphic display of 8 boxes represent the volume of liquid in an auxiliary tank. The tank name can be changed.(Refer to the “Edit” mode, page 22.) Oil Level or Engine Temp or Water Pressure or Manifold Pressure or Boost Pressure. Displays Oil Level on 2 cycle outboards and Jet Drives. Displays Engine Temp on 4 cycle outboards. Displays Water Pressure on inboard/outboards, and inboards. Displays Manifold Pressure on Verado outboards, and displays Boost Pressure on diesel engines. Water Press or Engine Temp or Oil Temp or Gear Pressure Displays Water Pressure on 2 cycle, 4 cycle and Jet drives. Displays Engine Temp on inboard/outboards and inboards. Displays Oil Temp on Verado outboards and Gear Press on diesel engines. Default Screen “8” depth sounder is being received on the SmartCraft bus. Depth Displays water depth under the depth transducer as received from the SmartCraft bus. Shallow set Displays shallow depth alarm setting entered by the user. Keel offset Displays the keel offset entered by the user. Negative numbers indicate that the Depth Sounder transducer is located ABOVE the deepest part of the hull (typical). Allow for worst case boat loading when adjusting the Keel Offset as this setting affects the Shallow Alarm. Default Screen “9” This screen displays fault conditions as described in the “Alarm” mode section page 29 of this manual. The following screen appears if a valid Page 8
Page 1 and 2: Owner’s Manual SmartCraft MG2000
Page 3 and 4: Set Invert Steering Angle page 22 S
Page 5 and 6: Verado Default (Break-In defaults t
Page 7 and 8: lights on maximum level): 420 mA. T
Page 9: equired. The setting for the tachom
Page 13 and 14: Select RPM/Speed RPM Turn Troll on/
Page 15 and 16: INSTRUCTIONS - FUNCTION Line Displa
Page 17 and 18: Adjust the engines’s trim to the
Page 19 and 20: Press and hold the “Up” and “
Page 21 and 22: Press and hold the “Up” and “
Page 23 and 24: Press “Up” or “Down” to sel
Page 25 and 26: Press “Up” or “Down” to sel
Page 27 and 28: Press “Up” or “Down” to scr
Page 29 and 30: Press “Up” or “Down” to scr
Page 31 and 32: Available functions for display in
Page 33 and 34: Shallow Alarm Warns that water dept
Page 35 and 36: Oil Pump Fault There is an oil pump
Page 37 and 38: $1Ax.09:4-5 Battery Voltage $1Ax.0A
Page 39 and 40: MG2000 Speedometer Harness HN0403 S
Page 41 and 42: MG2000 Speedometer Harness HN0407 S
Page 43 and 44: Harness HN0566 SmartCraft Tachomete
Page 45 and 46: Harness HN0401 NMEA 0183 Cable NMEA
Page 48: 2/27/06 8/1/06 Copyright 2006 by th

Owner's Manual - Faria Instruments

Create successful ePaper yourself

Delete template?

Save as template?