Raychem Heatshrink Products - RB Racing

More documents

Recommendations

Info

Application Tooling Product Facts ■ Closed-loop speed and temperature control ■ CE approved for worldwide use ■ Adaptable for different applications ■ Continuous controlled process Model 19 Conveyor Heater for Processing <strong>Raychem</strong> Heat-Shrinkable Tubing and Termination Devices Applications The Model 19 conveyor heater is the latest generation of reliable and versatile process heaters for a wide variety of heat-shrinkable products. Two sets of timing belts grip the individual assemblies and carry them through a closed-loop infrared heating zone, then through a cooling zone, and deposit the completed assemblies in a collection bin. The processor was designed to meet the requirements of the European Safety Directives and is CE approved, allowing for worldwide use. The processor is designed to operate on the following line voltages: 210 to 240 Vac, 20 A, 1 Ø, 50/60 Hz. Options for this processor include: ■ Powered or unpowered extension tables to support long or heavy harnesses. ■ ■ ■ ■ Kit for processing ring terminals and end terminations. Floor stand with wheels. Wider heating elements for tubing up to 178 [7.0] long. Narrow heating elements for SolderSleeve devices up to 10 [0.4] diameter and 45 [1.8] long or short length tubing less than 50 mm [2.0]. Product Features Controlled Heating Zone The Model 19 has two etched- foil heating elements mounted under a quartz face. Consistent heating chamber temperatures are obtained with a closed-loop temperature controller. There is a lockout on the controller to prevent unauthorized changes. Speed Control Consistent speed is obtained with a closed-loop speed controller. The speed is adjusted using a 3-digit thumbwheel on the front control panel. There is a lockout on the thumbwheel to prevent unauthorized changes. Minimal Skill Requirements There are clearly marked guides for aligning the assembly as well as the tubing or device being processed. The operator only has to center the assembly; the grippers carry it through the heating and cooling zone and deposit it into the unloading bin. Economical Production The throughput rate is determined by the rate at which an operator can load the processor. Versatility The tool description CLTEQ- M19-Belt-htr part number 714529-000 will handle tubing up to 25 [1.0] diameter and 102 [4.0] long. Tubing up to 178 [7.0] long can be handled with the use of tool description CLTEQ-M19- Belt-Htr-6in part number 075131-000. The tool description CLTEQ-M19- Beltheater-SS part number D43037-000 will handle SolderSleeve devices up to 10 [0.4] diameter and 45 [1.8] long, or short length tubing (less than 50 [2.0], where applications require a narrow heat width. Self-Diagnostic Circuitry There are several “selfdiagnostic” circuits that alert the operator if any major component fails or if an unsafe processing condition occurs. A light will turn on and a lockout gate will lift in the entry zone, preventing the operator from loading assemblies until the situation has been corrected. Other Features Include: ■ ■ ■ Emergency stop. Automatic cool-down circuit to extend the life of components. Lockout on temperature and speed controllers to prevent unauthorized changes. 10198 Catalog 1308940 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514 Revised 5-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Japan: 81-44-900-5102 specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Singapore: 65-4866-151 www.tycoelectronics.com are U.S. equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-1793-528171
Application Tooling Model 19 Conveyor Heater for Processing <strong>Raychem</strong> Heat-Shrinkable Tubing and Termination Devices (Continued) Specifications and Dimensions Electrical Power requirements Heating elements 210–240 Vac, 20 A, 1 Ø, 50/60 Hz Std = 3160 W/Wide = 3320 W/Narrow = 1760 W Mechanical Conveyor belt system Double-sided timing belts, pitch - 9.5 [0.375] Belt speed Up to 152 cm/min [5.0/min] Processor dimensions 53 cm [21] W, 135 cm [53] L, 45 cm [18] H Shipping dimensions 66 cm [26] W, 147 cm [58] L, 58 cm [23] H Shipping weight with crate 86 kg [190 lb] Tubing sizes Tubing diameter (max) 25 [1.0] 102 [4.0] Tubing length (max) 178 [7.0] wide heating element tool 50 [2.0] narrow heating element tool Work-piece length (min) 240 [9.5] Version Part No. Model 19 Standard 714529-000 Model 19 Wide 075131-000 Model 19 Narrow D43037-000 10 Heat-Shrink Tubing, Molded Parts and Adhesives Catalog 1308940 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514 Revised 5-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Japan: 81-44-900-5102 specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Singapore: 65-4866-151 www.tycoelectronics.com are U.S. equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-1793-528171 10199
Page 1 and 2:
Molded Parts Part Numbering System
Page 3 and 4:
Adhesives Table of Contents Tyco El
Page 5 and 6:
Adhesives Adhesive/Sealant Product
Page 7 and 8:
Adhesives Installation Guide Substr
Page 9 and 10:
Adhesives Installation Guide (Conti
Page 11 and 12:
Heat-Shrink Tubing, Molded Parts an
Page 13 and 14:
Heat-Shrink Tubing, Molded Parts an
Page 15 and 16:
Single-Wall Tubing CRN (Continued)
Page 17 and 18:
Single-Wall Tubing DCPT (Continued)
Page 19 and 20:
Single-Wall Tubing DR-25 (Continued
Page 21 and 22:
Single-Wall Tubing MicroFit (Contin
Page 23 and 24:
Single-Wall Tubing NT/NTFR (Continu
Page 25 and 26:
Single-Wall Tubing NT-MIL (Continue
Page 27 and 28:
Single Wall Tubing RNF-100 (Continu
Page 29 and 30:
Single Wall Tubing RNF-150 (Continu
Page 31 and 32:
Single Wall Tubing RNF-3000 (Contin
Page 33 and 34:
Single Wall Tubing RP-4800 (Continu
Page 35 and 36:
Single Wall Tubing RT-3 (Continued)
Page 37 and 38:
Single Wall Tubing RT-375 (Continue
Page 39 and 40:
Single Wall Tubing RT555 (Continued
Page 41 and 42:
Single Wall Tubing RW-175 (Continue
Page 43 and 44:
Single Wall Tubing SFR (Continued)
Page 45 and 46:
Single Wall Tubing SRFR (Continued)
Page 47 and 48:
Single Wall Tubing Versafit (Contin
Page 49 and 50:
Single Wall Tubing Versafit V4 (Con
Page 51 and 52:
Single Wall Tubing Viton/Viton-HW/V
Page 53 and 54:
Single Wall Tubing ZH-100 (Continue
Page 55 and 56:
Single Wall Tubing ZHTM (Continued)
Page 57 and 58:
Adhesive Lined Tubing ATUM (Continu
Page 59 and 60:
Adhesive Lined Tubing DWP-125 (Cont
Page 61 and 62:
Adhesive Lined Tubing ES1000 (Conti
Page 63 and 64:
Adhesive Lined Tubing ES2000 (Conti
Page 66 and 67:
Adhesive Lined Tubing HCTE Helical
Page 68 and 69:
Adhesive Lined Tubing PD Caps Semi-
Page 70 and 71:
Adhesive Lined Tubing RayBlock 85 H
Page 72 and 73:
Adhesive Lined Tubing RayBlock 105
Page 74 and 75:
Adhesive Lined Tubing SCL Semirigid
Page 76 and 77:
Adhesive Lined Tubing SCT Flame-Ret
Page 78 and 79:
Adhesive Lined Tubing TAT-125 Adhes
Page 80 and 81:
Heavy-Walled Tubing BSTS/BSTS-FR Ge
Page 82 and 83:
Heavy-Walled Tubing HF High-Flex, H
Page 84 and 85:
Heavy-Walled Tubing HRHF/HRNF/HRSR
Page 86 and 87:
Heavy-Walled Tubing SST/SST-FR Self
Page 88 and 89:
Heavy-Walled Tubing XFFR Halogen-Fr
Page 90 and 91:
Molded Parts Shapes Introduction Ra
Page 92 and 93:
Molded Parts Shape Selection Tables
Page 94 and 95:
Molded Parts Part Numbering System
Page 96 and 97:
Molded Parts Visual Selection Guide
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Molded Parts Boot Adapter Selection
Page 110 and 111:
Molded Parts Boot Adapter Selection
Page 112 and 113:
Molded Parts — Materials -3 Semi-
Page 114 and 115:
Molded Parts — Materials -4 Flexi
Page 116 and 117:
Molded Parts — Materials -12 Modi
Page 118 and 119:
Molded Parts — Materials -25 Flui
Page 120 and 121:
Molded Parts — Materials -25S Flu
Page 122 and 123:
Molded Parts — Materials -50 Flui
Page 124 and 125:
Molded Parts — Materials -51 Chem
Page 126 and 127:
Molded Parts — Materials -55 Flex
Page 128 and 129:
Molded Parts — Materials -71 Semi
Page 130 and 131:
Molded Parts — Materials -100 Low
Page 132 and 133:
Molded Parts — Materials -100S Lo
Page 134 and 135:
Molded Parts — Materials -125 Fle
Page 136 and 137:
Molded Parts — Caps End Caps, 101
Page 138 and 139:
Molded Parts — Caps SSC Heat-Shri
Page 140 and 141:
Molded Parts — Boots 202A111 to 1
Page 142 and 143:
Molded Parts — Boots 202D121 to 1
Page 144 and 145:
Page 146 and 147:
R Tan Tan Molded Parts — Boots 20
Page 148 and 149:
Molded Parts — Boots 202K121 to 1
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Molded Parts — Boots 222F211 to 2
Page 158 and 159: Molded Parts — Boots 234A011 to 0
Page 160 and 161: Molded Parts — Boots 234A611 to 6
Page 162 and 163: Molded Parts — Feedthroughs 207W2
Page 164 and 165: Molded Parts — Transition 301A511
Page 170 and 171: Molded Parts — Transition 382C312
Page 174 and 175: Molded Parts — Transition QFT Con
Page 176 and 177: Molded Parts — Transition SSB, T,
Page 178 and 179: Molded Parts — Accessories 202W30
Page 180 and 181: Molded Parts — Accessories 400W24
Page 182 and 183: Molded Parts — Accessories CES Ch
Page 184 and 185: Molded Parts — Accessories CES (C
Page 186 and 187: Molded Parts — Accessories RayOLO
Page 188 and 189: Molded Parts — Accessories shrink
Page 190 and 191: Molded Parts shrinkHOoP (Continued)
Page 192 and 193: XL Products Ordering Information (C
Page 194 and 195: Adhesives Adhesive/Sealant Product
Page 196 and 197: Adhesives Installation Guide Substr
Page 198 and 199: Adhesives Installation Guide (Conti
Page 200 and 201: Application Tooling CV-1981 and CV-
Page 202 and 203: Application Tooling HL1802E and HL2
Page 204 and 205: Application Tooling Product Facts
Page 206 and 207: Application Tooling Model 16B Belt
Page 210 and 211: Application Tooling Model 81CE Disc
Page 212 and 213: Application Tooling Model 105 Tunne
Page 214: Application Tooling ThermoGun HG Ho
show all

Raychem Heatshrink Products - RB Racing

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?