Raychem Heatshrink Products - RB Racing

More documents

Recommendations

Info

Heavy-Walled Tubing XFFR Halogen-Free, Flame-Retardant, Heat-Shrinkable Tubing Product Facts ■ Emits minimal amounts of toxic or acid gases during combustion ■ Meets performance requirements of MIL-C- 24640 and MIL-C-24643 cable jackets ■ Resists moisture, fungus, and weathering ■ Available in expansion ratios as high as 3:1 ■ XFFR has the following approvals: - ABS (American Bureau of Shipping) - DNV (Det Norske Veritas) - Lloyd’s (Lloyd’s Register of Shipping) Applications XFFR halogen-free tubing can be used for rejacketing and repairing halogen-free cables in any enclosed area where a flame-retardant, halogen-free environment is required. These environments include tunnels, buildings, mass transit vehicles, and ships. When installed with SFTS-FR1 tape, the tubing can also be used in applications requiring water sealing and protection from abrasion and corrosion. Installation Minimum shrink temperature: 70°C [158°F] Minimum full recovery temperature: 121°C [250°F] Operating Temperature Range -55°C to 105°C [-67°F to 221°F] Specifications/Approvals Series Military Industry <strong>Raychem</strong> XFFR MIL-C-24643 NES 713 RW-2016 NES 711 10078 Catalog 1308940 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514 Revised 5-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Japan: 81-44-900-5102 specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Singapore: 65-4866-151 www.tycoelectronics.com are U.S. equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-1793-528171
Heavy-Walled Tubing XFFR (Continued) Product Dimensions Inside Diameter Recovered Wall Thickness* Size Minimum Expanded Maximum Recovered After Heating as Supplied After Heating (Nominal) XFFR-03 7.62 [0.300] 2.54 [0.100] 1.52 [0.060] XFFR-04 10.16 [0.400] 3.81 [0.150] 1.52 [0.060] XFFR-07 19.05 [0.750] 5.59 [0.220] 2.03 [0.080] XFFR-11 27.94 [1.100] 9.52 [0.375] 2.67 [0.105] XFFR-15 38.10 [1.500] 12.70 [0.500] 3.05 [0.120] XFFR-20 50.80 [2.000] 19.05 [0.750] 3.05 [0.120] XFFR-30 76.20 [3.000] 31.75 [1.250] 3.94 [0.155] *Wall thickness will be less if tubing recovery is restricted during shrinkage. Ordering Information Color Standard Black (-0) Size selection Always order the largest size that will shrink snugly over the component to be covered. Standard packaging 1.2-meter [4-foot] or 7.5-meter [25-foot] lengths. Part Numbering System XFFR - 03 X 4 / NM “NM” - no mark Length in feet (4 feet standard) Size No adhesive. Family 10 Heat-Shrink Tubing, Molded Parts and Adhesives Catalog 1308940 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514 Revised 5-03 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Japan: 81-44-900-5102 specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Singapore: 65-4866-151 www.tycoelectronics.com are U.S. equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-1793-528171 10079
Page 1 and 2:
Molded Parts Part Numbering System
Page 3 and 4:
Adhesives Table of Contents Tyco El
Page 5 and 6:
Adhesives Adhesive/Sealant Product
Page 7 and 8:
Adhesives Installation Guide Substr
Page 9 and 10:
Adhesives Installation Guide (Conti
Page 11 and 12:
Heat-Shrink Tubing, Molded Parts an
Page 13 and 14:
Heat-Shrink Tubing, Molded Parts an
Page 15 and 16:
Single-Wall Tubing CRN (Continued)
Page 17 and 18:
Single-Wall Tubing DCPT (Continued)
Page 19 and 20:
Single-Wall Tubing DR-25 (Continued
Page 21 and 22:
Single-Wall Tubing MicroFit (Contin
Page 23 and 24:
Single-Wall Tubing NT/NTFR (Continu
Page 25 and 26:
Single-Wall Tubing NT-MIL (Continue
Page 27 and 28:
Single Wall Tubing RNF-100 (Continu
Page 29 and 30:
Single Wall Tubing RNF-150 (Continu
Page 31 and 32:
Single Wall Tubing RNF-3000 (Contin
Page 33 and 34:
Single Wall Tubing RP-4800 (Continu
Page 35 and 36:
Single Wall Tubing RT-3 (Continued)
Page 37 and 38: Single Wall Tubing RT-375 (Continue
Page 39 and 40: Single Wall Tubing RT555 (Continued
Page 41 and 42: Single Wall Tubing RW-175 (Continue
Page 43 and 44: Single Wall Tubing SFR (Continued)
Page 45 and 46: Single Wall Tubing SRFR (Continued)
Page 47 and 48: Single Wall Tubing Versafit (Contin
Page 49 and 50: Single Wall Tubing Versafit V4 (Con
Page 51 and 52: Single Wall Tubing Viton/Viton-HW/V
Page 53 and 54: Single Wall Tubing ZH-100 (Continue
Page 55 and 56: Single Wall Tubing ZHTM (Continued)
Page 57 and 58: Adhesive Lined Tubing ATUM (Continu
Page 59 and 60: Adhesive Lined Tubing DWP-125 (Cont
Page 61 and 62: Adhesive Lined Tubing ES1000 (Conti
Page 63 and 64: Adhesive Lined Tubing ES2000 (Conti
Page 66 and 67: Adhesive Lined Tubing HCTE Helical
Page 68 and 69: Adhesive Lined Tubing PD Caps Semi-
Page 70 and 71: Adhesive Lined Tubing RayBlock 85 H
Page 72 and 73: Adhesive Lined Tubing RayBlock 105
Page 74 and 75: Adhesive Lined Tubing SCL Semirigid
Page 76 and 77: Adhesive Lined Tubing SCT Flame-Ret
Page 78 and 79: Adhesive Lined Tubing TAT-125 Adhes
Page 80 and 81: Heavy-Walled Tubing BSTS/BSTS-FR Ge
Page 82 and 83: Heavy-Walled Tubing HF High-Flex, H
Page 84 and 85: Heavy-Walled Tubing HRHF/HRNF/HRSR
Page 86 and 87: Heavy-Walled Tubing SST/SST-FR Self
Page 90 and 91: Molded Parts Shapes Introduction Ra
Page 92 and 93: Molded Parts Shape Selection Tables
Page 94 and 95: Molded Parts Part Numbering System
Page 96 and 97: Molded Parts Visual Selection Guide
Page 108 and 109: Molded Parts Boot Adapter Selection
Page 110 and 111: Molded Parts Boot Adapter Selection
Page 112 and 113: Molded Parts — Materials -3 Semi-
Page 114 and 115: Molded Parts — Materials -4 Flexi
Page 116 and 117: Molded Parts — Materials -12 Modi
Page 118 and 119: Molded Parts — Materials -25 Flui
Page 120 and 121: Molded Parts — Materials -25S Flu
Page 122 and 123: Molded Parts — Materials -50 Flui
Page 124 and 125: Molded Parts — Materials -51 Chem
Page 126 and 127: Molded Parts — Materials -55 Flex
Page 128 and 129: Molded Parts — Materials -71 Semi
Page 130 and 131: Molded Parts — Materials -100 Low
Page 132 and 133: Molded Parts — Materials -100S Lo
Page 134 and 135: Molded Parts — Materials -125 Fle
Page 136 and 137: Molded Parts — Caps End Caps, 101
Page 138 and 139:
Molded Parts — Caps SSC Heat-Shri
Page 140 and 141:
Molded Parts — Boots 202A111 to 1
Page 142 and 143:
Molded Parts — Boots 202D121 to 1
Page 144 and 145:
Page 146 and 147:
R Tan Tan Molded Parts — Boots 20
Page 148 and 149:
Molded Parts — Boots 202K121 to 1
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Molded Parts — Boots 222F211 to 2
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Molded Parts — Feedthroughs 207W2
Page 164 and 165:
Molded Parts — Transition 301A511
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Molded Parts — Transition 382C312
Page 172 and 173:
Page 174 and 175:
Molded Parts — Transition QFT Con
Page 176 and 177:
Molded Parts — Transition SSB, T,
Page 178 and 179:
Molded Parts — Accessories 202W30
Page 180 and 181:
Molded Parts — Accessories 400W24
Page 182 and 183:
Molded Parts — Accessories CES Ch
Page 184 and 185:
Molded Parts — Accessories CES (C
Page 186 and 187:
Molded Parts — Accessories RayOLO
Page 188 and 189:
Molded Parts — Accessories shrink
Page 190 and 191:
Molded Parts shrinkHOoP (Continued)
Page 192 and 193:
XL Products Ordering Information (C
Page 194 and 195:
Adhesives Adhesive/Sealant Product
Page 196 and 197:
Adhesives Installation Guide Substr
Page 198 and 199:
Adhesives Installation Guide (Conti
Page 200 and 201:
Application Tooling CV-1981 and CV-
Page 202 and 203:
Application Tooling HL1802E and HL2
Page 204 and 205:
Application Tooling Product Facts
Page 206 and 207:
Application Tooling Model 16B Belt
Page 208 and 209:
Application Tooling Product Facts
Page 210 and 211:
Application Tooling Model 81CE Disc
Page 212 and 213:
Application Tooling Model 105 Tunne
Page 214:
Application Tooling ThermoGun HG Ho
show all

Raychem Heatshrink Products - RB Racing

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?