HP Color LaserJet 2600n Service Manual - ENWW - Market Point

More documents

Recommendations

Info

Model and serial number location The model number and serial numbers are listed on identification labels located on the rear of the printer. The model number is alphanumeric, such as Q6455A, for the HP Color LaserJet 2600n printer. The serial number contains information about the country/region of origin, the printer version, production code, and the production number of the printer. Figure 1-5 Model and serial number information Control panel Understanding supplies status The supplies gauges show the consumption levels of print cartridges (black, yellow, cyan, and magenta). Black, yellow, cyan, and magenta supplies status gauges A ? appears instead of the consumption level when the level is not known. This can occur in the following circumstances: ■ Missing cartridges ■ Incorrectly placed cartridges ■ Cartridges with an error ■ Some non-HP cartridges The supplies gauge appears whenever the printer shows the Ready state with no warnings. It will also appear when the printer shows a warning or error message concerning a print cartridge or multiple supplies. If a supply is empty, the gauge will flash. Understanding printer status Cancel Job button ■ When the Ready light is blinking, pressing (CANCEL JOB) cancels the current job. ■ When a supplies status gauge is blinking and the Attention light is on (indicating that a non-HP supply has been installed), pressing (SELECT) allows you to continue printing. 8 Chapter 1 Product information ENWW
CAUTION You might not receive any indication when a non-HP supply is empty. For more information about using non-HP print cartridges, see HP policy on non-HP supplies. If you continue printing after the supply is empty, damage to the printer can occur. See Hewlett- Packard limited warranty statement. Attention light Generally, the Attention light blinks when the printer is out of paper, when a jam has occurred, or when other problems that need attention occur. The Attention light is on and one of the Supplies Status gauges is blinking the first time a non-HP supply is installed. Ready light The Ready light is on when the printer is ready to print (experiencing no errors that prevent printing) and blinks when it is receiving data to be printed. Ready light and Select button ■ When the Ready light is on and the Attention light is blinking, pressing (SELECT) continues the print job after you load print media for a manual feed, or clears some errors. ■ When the Ready light is blinking, the front door has been opened and then closed. Press (SELECT) to return the printer to the Ready state. If you do not press (SELECT), the printer returns to the Ready state on its own. Left and Right arrow buttons Use the (LEFT ARROW) and (RIGHT ARROW) buttons to navigate through the printer control panel menus. A Demo page can be printed by pressing the (LEFT ARROW) and (RIGHT ARROW) buttons simultaneously. Understanding control panel layout This section provides information about printer status and control panel layout. Control panel layout The printer contains the following lights and buttons on the control panel: ENWW Walk around 9
Page 3 and 4: HP Color LaserJet 2600n Service Man
Page 5 and 6: Table of contents 1 Product informa
Page 7 and 8: General timing chart ..............
Page 9 and 10: Diagnostic resources...............
Page 11 and 12: List of tables Table 1-1 Printer fe
Page 13 and 14: List of figures Figure 1-1 HP Color
Page 15 and 16: 1 Product information This section
Page 17 and 18: Printer configuration HP Color Lase
Page 19 and 20: Table 1-1 Printer features (continu
Page 21: Back and side view Figure 1-3 Back
Page 25 and 26: Software This section contains info
Page 27 and 28: Starting the Uninstaller 1 Click St
Page 29 and 30: Care should be taken not to purchas
Page 31 and 32: Labels Select the type of label tha
Page 33 and 34: ■ Labels that are not specificall
Page 35 and 36: 2 Installation This chapter contain
Page 37 and 38: ■ Walls or other objects. There m
Page 39 and 40: Install input devices Installing op
Page 41 and 42: Installing supplies Print cartridge
Page 43 and 44: 7 Align the print cartridge with th
Page 45 and 46: 3 Managing and maintenance This cha
Page 47 and 48: Storing supplies Follow these guide
Page 49 and 50: To clean the fuser using HP Toolbox
Page 51 and 52: 4 Operational theory This chapter c
Page 53 and 54: Figure 4-1 Engine control system Po
Page 55 and 56: Image formation system The image fo
Page 57 and 58: Image formation process Figure 4-3
Page 59 and 60: Figure 4-4 Latent image formation L
Page 61 and 62: Figure 4-7 Print cartridge structur
Page 63 and 64: The toner on the photosensitive dru
Page 65 and 66: Pickup and feed system The pickup/f
Page 67 and 68: SR4 Fuser delivery paper sensor SR5
Page 69 and 70: Solenoid, motor, and fan locations
Page 71 and 72: Figure 4-16 Location of 250-sheet t
Page 73 and 74:
Printer calibration Calibration set
Page 75 and 76:
5 Removal and replacement This chap
Page 77 and 78:
Service approach Field Service on t
Page 79 and 80:
4 Grasp both sides of the print car
Page 81 and 82:
2 Remove three (3) screws, two (2)
Page 83 and 84:
5 Remove the left cover. 6 Squeeze
Page 85 and 86:
9 Remove the small black cable cove
Page 87 and 88:
15 Remove the ETB. Use the followin
Page 89 and 90:
3 Remove two (2) screws from the ri
Page 91 and 92:
9 Lift up and remove the face-down
Page 93 and 94:
13 Unplug two (2) 3-pin optical enc
Page 95 and 96:
Use the following procedure to repl
Page 97 and 98:
3 Remove the rear plate. ENWW Remov
Page 99 and 100:
5 Remove four (4) screws from the f
Page 101 and 102:
4 Gently unplug 16 connectors. 5 Re
Page 103 and 104:
Paper pickup roller removal and rep
Page 105 and 106:
6 Rotating it towards the back, rem
Page 107 and 108:
5 Lift up and remove the upper face
Page 109 and 110:
9 Remove the control panel assembly
Page 111 and 112:
6 Troubleshooting This troubleshoot
Page 113 and 114:
Clearing jams This section contains
Page 115 and 116:
Where to look for jams Jams can occ
Page 117 and 118:
2 Carefully grasp the jammed paper
Page 119 and 120:
2 Open and close the front door. Pi
Page 121 and 122:
Print problems Getting information
Page 123 and 124:
Control panel message Description R
Page 125 and 126:
Page 127 and 128:
Reports menu The following reports
Page 129 and 130:
5 DC controller version. This secti
Page 131 and 132:
Table 6-5 Status log messages Error
Page 133 and 134:
The following secondary service men
Page 135 and 136:
Table 6-7 Extended print modes (con
Page 137 and 138:
6 Restart the computer and the devi
Page 139 and 140:
Functional tests (SERVICE ONLY) Eng
Page 141 and 142:
3 Turn on the printer. 4 When you s
Page 143 and 144:
Configuration page The Configuratio
Page 145 and 146:
Event log NOTE The color bars on th
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Table 6-13 General print quality is
Page 155 and 156:
Table 6-13 General print quality is
Page 157 and 158:
Table 6-14 Color document issues (c
Page 159 and 160:
NOTE If you have access to HP Toolb
Page 161 and 162:
Repetitive image defect ruler Use a
Page 163 and 164:
7 Parts and diagrams NOTE In this c
Page 165 and 166:
Table 7-1 Available replaceable par
Page 167 and 168:
ENWW Overview 153
Page 169 and 170:
Table 7-4 Assembly locations Ref De
Page 171 and 172:
Table 7-5 External panels and cover
Page 173 and 174:
Table 7-6 External panels and cover
Page 175 and 176:
Table 7-7 Upper assembly cover Ref
Page 177 and 178:
Table 7-8 Internal components (1 of
Page 179 and 180:
ENWW Internal assemblies 165
Page 181 and 182:
Table 7-9 Internal components (2 of
Page 183 and 184:
Page 185 and 186:
Table 7-10 Internal components (3 o
Page 187 and 188:
Page 189 and 190:
Table 7-11 Control panel assembly R
Page 191 and 192:
Table 7-12 Main drive assembly Ref
Page 193 and 194:
Page 195 and 196:
Table 7-13 Fuser assembly Ref Descr
Page 197 and 198:
Page 199 and 200:
Table 7-14 PCB assembly location Tr
Page 201 and 202:
Table 7-15 Tray 2 input tray (casse
Page 203 and 204:
ENWW Input devices 189
Page 205 and 206:
Table 7-16 250-sheet input tray (ca
Page 207 and 208:
Table 7-17 Tray 2 sheet input tray
Page 209 and 210:
Page 211 and 212:
Table 7-18 Paper pick-up feeder ass
Page 213 and 214:
Page 215 and 216:
Table 7-19 Tray 3 input tray (casse
Page 217 and 218:
Page 219 and 220:
Table 7-20 Paper pickup feeder asse
Page 221 and 222:
Table 7-21 Paper pickup feeder asse
Page 223 and 224:
Alphabetical parts list Table 7-22
Page 225 and 226:
Table 7-22 Alphabetical parts list
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Table 7-23 Numerical parts list (co
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
A Product specifications This chapt
Page 267 and 268:
Supplies specifications Table A-2 S
Page 269 and 270:
Environmental specifications Table
Page 271 and 272:
B Product warranty statements ENWW
Page 273 and 274:
Print Cartridge Limited Warranty St
Page 275 and 276:
C Regulatory statements This chapte
Page 277 and 278:
Laser safety statement The Center f
Page 279 and 280:
VCCI statement (Japan) Figure C-1 V
Page 281 and 282:
Finnish laser statement LASERTURVAL
Page 283 and 284:
Index Symbols/Numerics 600 dpi prin
Page 285 and 286:
transparencies 17 tray 1, types sup
Page 287 and 288:
engine control 38 image formation 4
show all

HP Color LaserJet 2600n Service Manual - ENWW - Market Point

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?