HP Color LaserJet 2600n Service Manual - ENWW - Market Point

More documents

Recommendations

Info

Table 1-5 Tray 1 and Tray 2 specifications (continued) Tray 1 and Tray 2 Dimensions 1 Weight Capacity 2 HP LaserJet glossy paper and HP LaserJet photo paper Maximum: 216 x 356 mm (8.5 x 14 inches) Same as the preceding listed minimum and maximum sizes. Up to 250 sheets for Tray 2 75 to 163 g/m 2 (20 to 43 lb) Single sheet of HP LaserJet glossy paper or HP LaserJet photo paper for Tray 1 Up to 25 mm (0.99 inch) stack height for Tray 2 HP Premium Cover paper 3 200 g/m 2 (75 lb) cover Single sheet of HP Cover paper for Tray 1 Transparencies and opaque film Thickness: 0.10 to 0.13 mm (3.9 to 5.1 mils) Labels Thickness: up to 0.23 mm (up to 9 mils) Up to 25 mm (0.99 inch) stack height for Tray 2 Single sheet of transparency or opaque film for Tray 1 Up to 50 sheets for Tray 2 Single sheet of labels for Tray 1 Up to 25 mm (0.99 inch) stack height for Tray 2 Envelopes Up to 90 g/m 2 (16 to 24 lb) Single envelope for Tray 1 Up to ten envelopes for Tray 2 1 The printer supports a wide range of standard and custom sizes of print media. Check the printer driver for supported sizes. 2 Capacity can vary depending on media weight and thickness, and environmental conditions. 3 Hewlett-Packard does not guarantee results when printing with other types of heavy paper. Optional Tray 3 specifications Table 1-6 Optional Tray 3 specifications Optional Tray 3 (250–sheet tray) Paper Minimum: 76 x 127 mm (3 x 5 inches) Dimensions 1 Weight Capacity 2 Maximum: 216 x 356 mm (8.5 x 14 inches) 60 to 163 g/m 2 (16 to 43 lb) Up to 250 sheets 1 The printer supports a wide range of standard and custom sizes of print media. Check the printer driver for supported sizes. 2 Capacity can vary depending on media weight and thickness, and environmental conditions. Unsupported media (media to avoid) Avoid using the following media: ■ Paper that has been stapled. Staples left in reused paper will cause printer damage that will require repairs that may not be covered under the warranty. ■ Sheets of labels that have been used more than once or partial sheets of labels 18 Chapter 1 Product information ENWW
■ Labels that are not specifically recommended for laser printers ■ Labels that are separating from the backing sheet or are wrinkled or damaged in any way ■ Transparencies that are not specifically recommended for laser printers ■ Media that has been stored in a high-humidity environment ■ Labels with exposed glue or adhesive ENWW Print-media specifications 19
Page 3 and 4: HP Color LaserJet 2600n Service Man
Page 5 and 6: Table of contents 1 Product informa
Page 7 and 8: General timing chart ..............
Page 9 and 10: Diagnostic resources...............
Page 11 and 12: List of tables Table 1-1 Printer fe
Page 13 and 14: List of figures Figure 1-1 HP Color
Page 15 and 16: 1 Product information This section
Page 17 and 18: Printer configuration HP Color Lase
Page 19 and 20: Table 1-1 Printer features (continu
Page 21 and 22: Back and side view Figure 1-3 Back
Page 23 and 24: CAUTION You might not receive any i
Page 25 and 26: Software This section contains info
Page 27 and 28: Starting the Uninstaller 1 Click St
Page 29 and 30: Care should be taken not to purchas
Page 31: Labels Select the type of label tha
Page 35 and 36: 2 Installation This chapter contain
Page 37 and 38: ■ Walls or other objects. There m
Page 39 and 40: Install input devices Installing op
Page 41 and 42: Installing supplies Print cartridge
Page 43 and 44: 7 Align the print cartridge with th
Page 45 and 46: 3 Managing and maintenance This cha
Page 47 and 48: Storing supplies Follow these guide
Page 49 and 50: To clean the fuser using HP Toolbox
Page 51 and 52: 4 Operational theory This chapter c
Page 53 and 54: Figure 4-1 Engine control system Po
Page 55 and 56: Image formation system The image fo
Page 57 and 58: Image formation process Figure 4-3
Page 59 and 60: Figure 4-4 Latent image formation L
Page 61 and 62: Figure 4-7 Print cartridge structur
Page 63 and 64: The toner on the photosensitive dru
Page 65 and 66: Pickup and feed system The pickup/f
Page 67 and 68: SR4 Fuser delivery paper sensor SR5
Page 69 and 70: Solenoid, motor, and fan locations
Page 71 and 72: Figure 4-16 Location of 250-sheet t
Page 73 and 74: Printer calibration Calibration set
Page 75 and 76: 5 Removal and replacement This chap
Page 77 and 78: Service approach Field Service on t
Page 79 and 80: 4 Grasp both sides of the print car
Page 81 and 82: 2 Remove three (3) screws, two (2)
Page 83 and 84:
5 Remove the left cover. 6 Squeeze
Page 85 and 86:
9 Remove the small black cable cove
Page 87 and 88:
15 Remove the ETB. Use the followin
Page 89 and 90:
3 Remove two (2) screws from the ri
Page 91 and 92:
9 Lift up and remove the face-down
Page 93 and 94:
13 Unplug two (2) 3-pin optical enc
Page 95 and 96:
Use the following procedure to repl
Page 97 and 98:
3 Remove the rear plate. ENWW Remov
Page 99 and 100:
5 Remove four (4) screws from the f
Page 101 and 102:
4 Gently unplug 16 connectors. 5 Re
Page 103 and 104:
Paper pickup roller removal and rep
Page 105 and 106:
6 Rotating it towards the back, rem
Page 107 and 108:
5 Lift up and remove the upper face
Page 109 and 110:
9 Remove the control panel assembly
Page 111 and 112:
6 Troubleshooting This troubleshoot
Page 113 and 114:
Clearing jams This section contains
Page 115 and 116:
Where to look for jams Jams can occ
Page 117 and 118:
2 Carefully grasp the jammed paper
Page 119 and 120:
2 Open and close the front door. Pi
Page 121 and 122:
Print problems Getting information
Page 123 and 124:
Control panel message Description R
Page 125 and 126:
Page 127 and 128:
Reports menu The following reports
Page 129 and 130:
5 DC controller version. This secti
Page 131 and 132:
Table 6-5 Status log messages Error
Page 133 and 134:
The following secondary service men
Page 135 and 136:
Table 6-7 Extended print modes (con
Page 137 and 138:
6 Restart the computer and the devi
Page 139 and 140:
Functional tests (SERVICE ONLY) Eng
Page 141 and 142:
3 Turn on the printer. 4 When you s
Page 143 and 144:
Configuration page The Configuratio
Page 145 and 146:
Event log NOTE The color bars on th
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Table 6-13 General print quality is
Page 155 and 156:
Table 6-13 General print quality is
Page 157 and 158:
Table 6-14 Color document issues (c
Page 159 and 160:
NOTE If you have access to HP Toolb
Page 161 and 162:
Repetitive image defect ruler Use a
Page 163 and 164:
7 Parts and diagrams NOTE In this c
Page 165 and 166:
Table 7-1 Available replaceable par
Page 167 and 168:
ENWW Overview 153
Page 169 and 170:
Table 7-4 Assembly locations Ref De
Page 171 and 172:
Table 7-5 External panels and cover
Page 173 and 174:
Table 7-6 External panels and cover
Page 175 and 176:
Table 7-7 Upper assembly cover Ref
Page 177 and 178:
Table 7-8 Internal components (1 of
Page 179 and 180:
ENWW Internal assemblies 165
Page 181 and 182:
Table 7-9 Internal components (2 of
Page 183 and 184:
Page 185 and 186:
Table 7-10 Internal components (3 o
Page 187 and 188:
Page 189 and 190:
Table 7-11 Control panel assembly R
Page 191 and 192:
Table 7-12 Main drive assembly Ref
Page 193 and 194:
Page 195 and 196:
Table 7-13 Fuser assembly Ref Descr
Page 197 and 198:
Page 199 and 200:
Table 7-14 PCB assembly location Tr
Page 201 and 202:
Table 7-15 Tray 2 input tray (casse
Page 203 and 204:
ENWW Input devices 189
Page 205 and 206:
Table 7-16 250-sheet input tray (ca
Page 207 and 208:
Table 7-17 Tray 2 sheet input tray
Page 209 and 210:
Page 211 and 212:
Table 7-18 Paper pick-up feeder ass
Page 213 and 214:
Page 215 and 216:
Table 7-19 Tray 3 input tray (casse
Page 217 and 218:
Page 219 and 220:
Table 7-20 Paper pickup feeder asse
Page 221 and 222:
Table 7-21 Paper pickup feeder asse
Page 223 and 224:
Alphabetical parts list Table 7-22
Page 225 and 226:
Table 7-22 Alphabetical parts list
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Table 7-23 Numerical parts list (co
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
A Product specifications This chapt
Page 267 and 268:
Supplies specifications Table A-2 S
Page 269 and 270:
Environmental specifications Table
Page 271 and 272:
B Product warranty statements ENWW
Page 273 and 274:
Print Cartridge Limited Warranty St
Page 275 and 276:
C Regulatory statements This chapte
Page 277 and 278:
Laser safety statement The Center f
Page 279 and 280:
VCCI statement (Japan) Figure C-1 V
Page 281 and 282:
Finnish laser statement LASERTURVAL
Page 283 and 284:
Index Symbols/Numerics 600 dpi prin
Page 285 and 286:
transparencies 17 tray 1, types sup
Page 287 and 288:
engine control 38 image formation 4
show all

HP Color LaserJet 2600n Service Manual - ENWW - Market Point

Create successful ePaper yourself

Delete template?

Save as template?