Vessels catalogue (complete) - Juchheim LaborgerÃ¤te GmbH

More documents

Recommendations

Info

Custom and special purpose vessels Reservoirs Reservoirs have a conical bottom, which ensures that the contents are <strong>complete</strong>ly drained. They can be supplied with or without a heating jacket. The lid is welded on permanently forming a pressure seal, and is fitted with a pressure gauge, an excess pressure valve, a plug valve and a B29 conical adaptor with cap. The outlet has a plug valve and a short connection tube. See page 29 Pressure filter vessel with paper holder The vessel has a cylindrical pressure-tight body. An internal, flat, horizontal partition carries a filter paper. The conical lower section collects the filtrate. The vessels are available with or without heating jackets. See page 32 Glass vessel with metal lid For special purposes a glass vessel with a metal lid is available. The associated safety cage, in which accessories such as the stirrer drive and thermostat are mounted, adds to the operator’s safety. If required, a fire suppression trough (page 97) can be placed under the glass vessel. The lid will accept the same fittings that are used for all-metal vessels. See page 33 Stainless steel transport vessels Transport vessels have two lateral handles and have a loose-fitting lid. A stand is available to prevent the vessel from being tipped over accidentally. The vessels can be supplied with an outlet tap. See page 34 Tube-and-shell and Liebig condensers Tube-and-shell condensers with surface areas from 0.16 m² to 1 m² are available. Both ends can be fitted with various types of connector. Liebig condensers are straight tube with cooling jackets. We also manufacture coiled condensers and columns with various packings to customers’ requirements. See page 35 Custom manufacture of vessels During manufacture vessels can be equipped with special features such as: • Drain valves of various types and sizes • Rectangular or round lateral sightglasses • Temperature measurement points in the bottom or side of the vessel • Injection or sampling points in the bottom or side of the vessel See pages 21, 23, 37, 39 28
Custom and special purpose vessels Reservoir, cylindrical-conical pattern R3/8" 4571 Reservoir with heating jacket H ∅ 4571 R3/8" 3/8" BSP Valve 20451.00 3/8" BSP 205 ∅14x2 Connection tube 3/8" BSP Vessel Nominal Cat. no. PTFE gasket* Volume Pressure Dimensions Heating jacket capacity [ltr] with jacket without jacket [ltr] [Bar] ∅ [mm] H [mm] Volume [ltr] Pressure [Bar] 1 10190.01 10195.01 1,3 25 140 172 0,6 6 2 10191.01 10196.01 2,3 25 160 210 0,9 6 5 10192.01 10197.01 5,3 15 220 285 1,3 6 10 10193.01 10198.01 11 10 273 348 1,9 6 1–10 10199.01 Connection tube, 3/8" BSP upper inlet, 3/8" BSP underneath outlet * for Klingersil gaskets change the last digit of the <strong>catalogue</strong> no. to 4. 29
Page 1: Reaction vessels for pressure and v
Page 4 and 5: 54470 Bernkastel-Kues Deliveries Po
Page 6 and 7: Reaction vessels for vacuum Reactio
Page 8 and 9: Cylindrical-conical pressure vessel
Page 10 and 11: Reaction vessels for vacuum and pre
Page 26 and 27: 10 litre pressure vessel, rated at
Page 32 and 33: Reactor system with lifting stage
Page 34 and 35: Custom and special purpose vessels
Page 36 and 37: Custom and special purpose vessels
Page 38 and 39: Accessories Fittings and spare part
Page 40 and 41: Accessories Drain valves and access
Page 42 and 43: Accessories Pressure gauges Item Ca
Page 44 and 45: Accessories Safety devices for vess
Page 46 and 47: Accessories Thermometers, thermomet
Page 48 and 49: Accessories Adaptors for ports in v
Page 50 and 51: Accessories Lid gaskets for vessels
Page 52 and 53: Lifting jacks for vessels Fixed lid
Page 54 and 55: Stirrer drives Stirrer drive with s
Page 56 and 57: Torque measurement Torque measureme
Page 58 and 59: Stirrerheads ‘O’ and oil film s
Page 60 and 61: Stirrerheads ’O’ ring sealed st
Page 62 and 63: Stirrerheads Mechanically sealed st
Page 64 and 65: Stirrerheads Mechanically sealed st
Page 66 and 67: Stirrerheads Magnetically coupled s
Page 68 and 69: Stirrerheads Magnetically coupled s
Page 70 and 71: Stirrers When ordering please menti
Page 72 and 73: Stirrers Helical stirrers and Dispe
Page 74 and 75: Stirrers Turbine stirrers and Count
Page 76 and 77: Conical joint stirrerheads Stirrerh
Page 78 and 79: Conical joint stirrerheads Stirrers
Page 80 and 81:
Thermostats and accessories JUVO Th
Page 82 and 83:
Thermostats and accessories Output
Page 84 and 85:
Thermostats and accessories Accesso
Page 86 and 87:
Thermostats and accessories Accesso
Page 88 and 89:
M18x1.5 Thermostats and accessories
Page 90 and 91:
Thermostats and accessories Consuma
Page 92 and 93:
Öltemp Reaktor T1 T2 Öltemp Reakt
Page 94 and 95:
T2 INT T1 EXT RESET START STOP PAUS
Page 96 and 97:
Fire suppression troughs Fire suppr
Page 98 and 99:
Transportable turnkey plant with:
Page 100 and 101:
Index A Adaptors conical joint, no
Page 102 and 103:
Conditions of sale and payment Cond
Page 104 and 105:
Reaction vessel, 50 litres, in stai
Page 106 and 107:
B53 Köln- Krefeld Köln A3 A1 Daun
show all

Vessels catalogue (complete) - Juchheim LaborgerÃ¤te GmbH

Create successful ePaper yourself

Delete template?

Save as template?