FS4400 PCI Express State Analysis Probe User Manual - FuturePlus ...

More documents

Recommendations

Info

There is more detailed information on the Packet Decoder and Packet Viewer in the Agilent logic analyzer Help files contained in v3.50 or higher. 52
General Information Characteristics Standards Supported This chapter provides additional reference information including the characteristics and signal connections for the FS4400 probe. The following operating characteristics are not specifications, but are typical operating characteristics for the FS4400 probe. If the product is used in a manner not specified by manufacturer, then the protection provided by the equipment may become impaired. PCI Express Base Specification, Revision 1.0a and 1.1 Power Requirements Logic Analyzer Required Number of Probes Used Logic Analyzer State Clock Frequency 100-240VAC, 2 amps. Agilent 16715/6/7/9 or 16750/1/2 installed in the 16700A or 16700B frame, 16753 cards or better are recommended. 16910/11 or 16950 cards can be used in the 16900 frame. 1680x analyzers. See section on Connecting to the analyzer. The State Adapter Probe interface uses 8 cable headers of either the 40 pin or 80 pin type. 125MHz for x1 PCI Express Protocol Analysis or 250MHz for x2, x4 or x8. 250 MHz for x1 x2 x4 or x8 PCI Express 10b analysis. Environmental Temperature Non operating: -40 to +75 degrees C (-40 to +167 degrees F) Operating: 20 to 30 degrees C ( 68 – 86 degrees F) Altitude Operating: 4,6000m (15,000 ft) Non operating: 15,3000m (50,000 ft) Humidity Testing and Troubleshooting Servicing Up to 80% relative humidity. Avoid sudden, extreme temperature changes which would cause condensation on the FS4400 module. There are no automatic performance tests or adjustments for the FS4400 module. If a failure is suspected in the FS4400 module contact the factory or your FuturePlus Systems authorized distributor. The repair strategy for the FS4400 is module replacement. However, if parts of the FS4400 module are damaged or lost contact the factory for a list of replacement parts. 53
Page 1 and 2: FuturePlus Systems Corporation FS44
Page 3 and 4: Triggering.........................
Page 5 and 6: Product Warranty This FuturePlus Sy
Page 7 and 8: Analyzing the PCI Express Bus This
Page 9 and 10: It is strongly recommended that the
Page 11 and 12: FS4400 Probing Cables The FS4400 PC
Page 13 and 14: Flying Lead Probing (FS1036 cable a
Page 15 and 16: Installing your Software for the Fi
Page 17 and 18: It is important before you load a c
Page 19 and 20: PE440_16 - 2 way consists of 2 sepa
Page 21 and 22: 10b Mode Configuration Files 167xx
Page 23 and 24: PE10b_51 - 2 way consists of 34 cha
Page 25 and 26: After the data has been imported yo
Page 27 and 28: The user configures and controls th
Page 29 and 30: The functions provided on these for
Page 31 and 32: Pattern and Mask X8 Dialog The Pack
Page 33 and 34: TLP Pattern and Mask Dialog Ordered
Page 35 and 36: Filtering The Filter dialogue page
Page 37 and 38: Log File The status of the probe, a
Page 39 and 40: Labels (PCIe) Besides de-serializin
Page 41 and 42: Event Code label definitions (PCIe
Page 43 and 44: Triggering The configuration files
Page 45 and 46: Observing PCIe Link Activity in ASP
Page 47 and 48: Finding Stable PCIe Link Activity i
Page 49 and 50: Transaction Viewer The FS4400 Proto
Page 51: Packet Viewer Tool The Packet Viewe
Page 55 and 56: LAI Bit Definitions For a Single Di
Page 57: LAI Bit Definitions For a Single Di

FS4400 PCI Express State Analysis Probe User Manual - FuturePlus ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?