group 18 Trim, Seats and Convertible Top.pdf

More documents

Recommendations

Info

1 8-48 GROUP 18-Trim, Seats, And Convertible Top in the bow. Mark the tape indicating the centerline. 14. Measure and mark the center between the bond seams of the top center deck at the No.4 bow on the underside of the material. Install a 6-inch piece of masking tape on the top material inner surface at the centerline of the No.4 bow. Mark the centerline along the entire length of tape. (Refer to Fig. 13.) 15. With the bow locating gauge in place (refer to Step 13 under Removal and Fig. 15), install the belt center tack ing strip attaching screws to approximately 1/4 to 1/2-inch from the bottoming out position. Install the belt side front tacking strip attaching screws and tighten to within 1/4 to I /2-inch of bottoming. 16. Center the top material on the No.4 bow and pull it forward sufficiently to center the outboard bond seam on the No.4 bow (Fig. 13). Secure the top material to the No.4 bow with staples. 17. Install the two retainers in the No.2 and No.3 bow listings (Fig. 13). 18. Route the quarter deck retaining cables through the hold down sleeves in the top material and retain each cable at the rear (loosely) with the attaching nut and washer (Fig. 14). 19. Pull the top trim material forward over the No. I bow until the No.2 and No.3 bow listings (Fig. 13) are centered over their respective bows. While maintaining tension on the top trim, place a pencil mark on the outer surface of the trim material along the forward edge of the No. I bow. 20. Remove the two bow aligning gauges and reinstall the coat hooks (Fig. 4). 21. Fold the front edge of the top material back from the No.1 bow. Disengage the No.1 bow from the windshield header and prop it up about one foot above the header. 22. Apply an ample amount of trim cement C2AZ-19C525-A across the lower front surface of the No.1 bow including the tacking strip and to the adjacent inner surface of the top material. 23. Lower the No.1 bow onto the header but do not clamp it. With the top material properly centered on the No.1 bow, start at the outer front corners and alternately pull the material forward to the pencil aligning mark. Make certain that all wrinkles are removed, and then fold and cement the material to the underside of the bow. 24. Position the windshield header seal assembly (Fig. 13) and secure the seal and top material with staples. Trim off excess top material. 25. Cement the front and rear flaps to each side rail. Pierce holes in the flaps for the weatherstrip attachments. 26. Install the front side rail weatherstrip and the No.1 bow retainer. 27. Tighten the retainer cable ad- justment nut at each rear side rail sufficiently to hold the top material tightly against the rail. 28. Install the intermediate and rear side rail weatherstrips. Adjust as required (Fig. 2). 29. With the No.1 bow clamped to the header, tighten all belt tacking strip attaching screws securely. 30. Install the compartment trim to the belt side front tacking strip with the at~aching screws (Fig. 10). 31. Install the compartment trim with the seat back support lower ledge attaching screws (Fig. 10). 32. Install the rear seat back and cushion. 33. Remove the interior centerline tape strips. 34. Install the No.4 bow outside moulding retainer, insert the moulding and install the two end tips (Fig. 13). ROOF FRONT HEADER WEATHERSTRIP MERCURY FAIRLANE INTERMEDIATE, 1. Release the toggle clamps and lower the top. 2. Remove the screws attaching the weatherstrip retainer to the No. I bow and remove the reo:ainer (Fig. 17). 3. Remove the adjusting screws at the outboard ends of the No. I bow. FIG. 14-Top Stay Pad Webbing and Quarter Deck Retainer Cable Attachments- .Mustang
~ PART 18-3-Convertible Top 18-49 4. Remove the nuts retaining the weatherstrip to the right and left front side rails and remove the weatherstrip assembly. 5. Position the weatherstrip assembly to the No. I bow and install the retainer and retaining screws. 6. Install the adjusting screws at the outboard ends of the No. I bow. 7. Position the side rail sections of the weatherstrip and install the retaining nuts. 8. Adjust the weatherstrip for a good seal and tighten the retaining screws and nuts. 9. Raise the top and lock it to the windshield header. MUSTANG 1. Release the toggle clamps and partially lower the top. 2. Remove 12 screws attaching the weatherstrip retainer to the header and remove the retainer. 3. Remove 2 screws attaching the weatherstrip to the header at each corner (Fig. 16). 4. Remove 6 nuts and washers (3 each side) retaining the weatherstrip to the roof side rails and remove the weatherstrip. 5. Apply sealer to the header and roof side rails and place the new weatherstrip in position. 6. Install the weatherstrip retainer with 12 screws and the 2 weatherstrJp attaching screws at each corner. 7. Install 3 nuts and washers attaching the weatherstrip to each side rail. Trim the weatherstrip for a watertight fit (Fig. 16). 8. Raise the top and lock it to the windshield header. SIDE RAIL WEATHERSTRIP- CENTER AND/OR REAR- MERCURY INTERMEDIATE, FAIRLANE REMOVAL 1. Lower the top as far as required to carry-out the operation. 2. If removing the center weatherstrip, remove the three retaining tee nuts and separate the retainer from the side rail. This is not necessary on the rear side rail (Fig. 17). .B "-VT 'W'- 379361.52 , WA5HE~ Cr'- 351320.1,2 ~ -=- ..-r---Il~--7I ~ /~ ::::.\:-- 5EALEP It' I "'- ) j """" /,,;.~ -'~.// '::'/N ~ - CENTER SIDE FRONT SIDE RAIL WEATHERSTRIP 7653986 ~ 1 RETAINER 51352 j .~ RAIL WEATHER. STRIP-7651564.S .:::::::::::::::::::: 1 ~~~::::::-- /n. I""~~ ~ ,il It.., . . ~ REAR RAIL' WATER DEFLECTDR 53988.9 ~ ...,. VIEW-BB ./ ~~/ ~ -~ :"\ /~\\ N 1408-8 FIG. 16-Side Rail Weatherstrip. -Mustang
Page 1: PART 18-1 PAG E Interior Trim And R
Page 4 and 5: 1352-A FIG. 5. Typical Door Trim Pa
Page 6 and 7: 18-6 GROUP l8-Trim, Seats, And Conv
Page 8 and 9: 18-8 GROUP l8-Trim, Seats, And Conv
Page 10 and 11: 18-10 GROUP la-Trim, Seats, And Con
Page 12 and 13: F () - :~ ;: 18-12 GROUP l8-Trim, S
Page 14 and 15: 18-14 GROUP 18-Trim, Seats, And Con
Page 16 and 17: 18-16 GROUP l8-Trim, Seats, And Con
Page 18 and 19: 18-18 GROUP l8-Trim, Seats, And Con
Page 20 and 21: 18~20 GROUP l8-Trim, Seats, And Con
Page 22 and 23: turnbuckle or eye bolt enough turns
Page 24: 18-24 GROUP l8-Trim, Seats, And Con
Page 27 and 28: PART 18-2-Seats 1 8-27 9. Sec.ure t
Page 29 and 30: PART 18-2-Seats 18-29 A C \ JUTE BO
Page 31 and 32: the retaining screws. Also install
Page 33 and 34: PART 18-2-Seats 18-33 FIG. 16-Front
Page 35 and 36: 21 Care of Top Fabric , 3 Adjustmen
Page 37 and 38: PART 18-3-Convertible Top 1 8-37 )/
Page 39 and 40: PART 18-3-Convertible Top 18-39 obt
Page 41 and 42: ~ PART 18-3-Convertible Top 18-4 RO
Page 43 and 44: PART 18-3-Convertible Top 18-43 the
Page 45 and 46: ~ ~ m M -0 '" ~ il \\\tf) :\/ u \\\
Page 47: PART 18-3-Convertible Top 18-47 rea
Page 51: PART 18-3-Convertible Top 1 8-5 1 T

group 18 Trim, Seats and Convertible Top.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?