You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Daily operation<br />
Adjusting the sound<br />
Switching sound off/on<br />
Setting the volume<br />
Setting the sound mode<br />
- 20<br />
Sound off;<br />
Sound on: Press button again or set volume V+.<br />
V+/V– volume louder / quieter.<br />
The volume bar will be shown briefly if no other menu<br />
is displayed.<br />
Call Sound mode.<br />
34 Select the number of speakers you want to hear.<br />
Additional sound settings for volume adjustment and for Sound mode:<br />
➠ As long as you can still see the volume bar or the<br />
selection of speakers for sound mode:<br />
5 Call additional sound settings.<br />
34 Select sound setting,<br />
6 Go to the menu line below.<br />
34 Make changes.<br />
Sound settings via the <strong>TV</strong> menu<br />
Sound mode ...<br />
optimal (5) 4 3 2 1<br />
Volume Sound mode DPLII mode<br />
24<br />
➠ In normal <strong>TV</strong> mode, without other displays.<br />
Call <strong>TV</strong> menu.<br />
34 Select Sound,<br />
6 go to the menu line below.<br />
34 Select desired sound setting,<br />
6 Go to the menu line below.<br />
34 Make changes.<br />
Sound adjustment<br />
END<br />
Explanations of the sound settings:<br />
Sound mode<br />
optimal<br />
1<br />
2<br />
3<br />
4<br />
5<br />
Amplifier<br />
Sound<br />
adjustment<br />
Headphone vol.<br />
Loudness<br />
Dolby PLII<br />
mode<br />
Headphone volume<br />
more ...<br />
Loudspeaker/<br />
Headphone<br />
sound<br />
Auto Volume<br />
AV output<br />
signal<br />
Maximum<br />
volume<br />
Switch on<br />
volume<br />
Volume<br />
adjustment for<br />
current station<br />
Balance<br />
Select the number of speakers you want to hear. The<br />
selection depends on the connected sound components<br />
(from page 41) and on the transmitted audio signal.<br />
➠ If the number of speakers appears in brackets, the<br />
sound of missing speakers is transmitted by the existing<br />
speakers (virtual).<br />
The momentarily reproduced audio signal is output with<br />
the ideal number of speakers.<br />
Play centre sound or mono (left/right).<br />
Play front sound (L/R stereo).<br />
Play front and centre sound.<br />
Play front and surround sound.<br />
Play front, surround and centre sound.<br />
Play via an external HiFi amplifier. Selection is only possible<br />
if an amplifier has been selected in the sound components<br />
wizard (see page 46).<br />
➠ You can also enter the number of speakers with the<br />
numeric buttons of the remote control.<br />
Speech, Classical, Pop, Custom music, and Custom film<br />
sound.<br />
Adjust the headphones volume.<br />
Proper boost of bass and treble tones at low volume.<br />
Here you can make Dolby Pro Logic II sound settings for<br />
movie, music, matrix and personal settings. Menu item<br />
only appears with certain sound mode settings.<br />
call with OK.<br />
Selection possibility Mono/Stereo or Sound 1 or Sound<br />
2 for two-sound broadcasts separately for speakers and<br />
headphones. Only available for analogue stations.<br />
Reduces volume differences, e.g. for advertisements that<br />
are too loud.<br />
Sound selection for two-sound broadcasts.<br />
Determining the maximum volume that can be set.<br />
Specify the volume that is set when switching on the <strong>TV</strong><br />
set with the mains switch. This does not affect switching<br />
the set on from standby mode.<br />
The volume can differ according to the individual stations.<br />
If the sound is too loud or too quiet in relation to other<br />
stations, adjust the volume. When the menu is open, you<br />
can select the stations one after another with P+/P– and<br />
adjust every single station conveniently.<br />
Set Stereo-Balance so that the volume impression is identcal<br />
on the left and right.