Machine Manual - Production Tool Supply

More documents

Recommendations

Info

NOTES NOTE 1: The drive must be programmed for maximum RPM through the control. Cycle the drive forward and reverse allowing the spindle to obtain the extreme RPM ranges, if an error occurs during accel or decel the appropriate value should be enlarged. NOTE 2: The homing offset (LEVEL 2 BLOCKS→MISCELLANEOUS→HOMING OFFSET) is used only on machines equipped with Automatic <strong>Tool</strong> Changers. This will be adjusted from its original factory set value of 1024. After doing an M50 (orient spindle) command, adjust accordingly to correct the spindle home position. NOTE 3: Auto-tune values are set by following the instructions above. No manual entry is required. Electrical manual 3000.doc 28 OF 38 4/30/07
Anilam 3000 software update instructions 1. Press E-stop and plug in an external keyboard 2. Press F10 exit 3. Press clear then type password “Z48” ↵ (enter) 4. Now you are in DOS at the C:\P3M prompt * 5. Type “cd..” ↵ You will now be in the root directory c:\ 6. Type “md old”↵ This will create an old directory 7. Type “cd P3M” (*) This will return you to the P3M directory 8. Type “copy *.* c:\old”↵ This will copy all files to the old directory for backup purposes. If there is a problem with the software installation you can get your machine back to original operating software by copying all the files in the old directory back to the P3M directory. To do this type “cd..”↵ - “cd old” - “copy *.* c:\P3M” say yes to overwrite files. Power down to restore when completed copying files. 9. Now you can install the software update disk . (If you received the software via E-mail please copy all attached files to a clean 3.5” disk ) Type “a:”↵ 10. Type “install”↵ this will start the installation process follow the directions on the screen. 11. Once you have completed the installation process and your machine is functioning properly you must backup your configuration file onto the floppy disk in the electrical cabinet (usually mounted on the door). See the Anilam manual for directions. * When updating a 5000 control the directory is c:\P5M Electrical manual 3000.doc 29 OF 38 4/30/07
Page 1 and 2: FRYER MACHINE SYSTEMS MB-R SERIES M
Page 3 and 4: MECHANICAL DRAWINGS maintenance MB
Page 5 and 6: Z AXIS COLUMN maintenance MB R SERI
Page 7 and 8: X AXIS TABLE maintenance MB R SERIE
Page 9 and 10: Y AXIS SADDLE maintenance MB R SERI
Page 11 and 12: TOOL CHANGER maintenance MB R SERIE
Page 13 and 14: COUNTER WEIGHT maintenance MB R SER
Page 15 and 16: FRYER MACHINE SYSTEMS ELECTRICAL &
Page 17 and 18: SAFETY RULES READ BEFORE OPERATING
Page 19 and 20: Voltage checks (All voltages +/- 10
Page 21 and 22: MACHINE SERIAL NO._________________
Page 23 and 24: PANEL LAYOUT Electrical manual 3000
Page 25 and 26: 3000 OPTIONS Electrical manual 3000
Page 27 and 28: MB Q SERIES ELECTRICAL DRAWINGS Ele
Page 29 and 30: FRYER MB PART LIST DRAWING REF. - P
Page 31 and 32: 3000 OPTIONS Electrical manual 3000
Page 33 and 34: DWG REF.#302008516 3000 CABLE LAYOU
Page 35 and 36: DWG REF. #D000775 CONSOLE WIRING DI
Page 37 and 38: MAINTENANCE SCHEDULE FRYER MB SERIE
Page 39 and 40: PART II ADJUSTMENTS FOR ANILAM 3000
Page 41: BALDOR H2 VECTOR SPINDLE DRIVE PARA
Page 45 and 46: Renishaw Tool Probe Installation Th
Page 47 and 48: MATERIALS REQUIRED: -Hard Drive -Ma
Page 49 and 50: Loading IPI file Anilam 3000 Contro
Page 51 and 52: FURTHER INSTRUCTIONS Once the two f

Machine Manual - Production Tool Supply

Create successful ePaper yourself

Delete template?

Save as template?