19-Hand Tools (125-174).50_200310.qxd - Hanes Supply, Inc

Hand Tools3/8" Drive Impact SocketsImpact Sockets, Standard Length,6 PointFed. Spec.: GGG-W-660A; ANSI B107.2• Flank drive design allows the socket tocontact the fastener on the flats of theopening rather than the corners.Cat. EDP Size A B C D E FNo. No. (in) Type (in) (in) (in) (in) (in) (in) Lbs. Kgs.2-608 52259 1/4 I 1-1/32 11/16 1/2 7/32 9/16 7/32 .05 .022-610 52260 5/16 I 1-1/32 11/16 1/2 1/4 9/16 7/32 .06 .032-612 52261 3/8 I 1-1/32 11/16 5/8 9/32 9/16 7/32 .07 .032-614 52262 7/16 II 1-1/16 11/16 21/32 9/32 19/32 — .07 .032-616 52263 1/2 II 1-3/32 3/4 3/4 5/16 19/32 — .09 .042-618 52264 9/16 II 1-1/8 13/16 13/16 9/16 19/32 — .12 .052-620 52265 5/8 II 1-5/32 29/32 29/32 19/32 5/8 — .13 .062-622 52266 11/16 II 1-3/16 31/32 31/32 19/32 5/8 — .14 .062-624 52267 3/4 II 1-1/4 1-1/16 1-1/16 21/32 11/16 — .23 .10Impact Sockets, Deep Length, 6 PointFed. Spec.: GGG-W-660A; ANSI B107.2• Flank design reduces the possibility of fastenerrounding.• Deep length sockets most commonly used toaccess recessed fasteners.Complete Contractor and Industrial Supplier • Sling and Rigging Specialist Since 1930Visit us online at www.hanessupply.comType IBolt.Cat. EDP Size A B C D E Clear. FNo. No. (in) Type (in) (in) (in) (in) (in) Dia. (in) Lbs. Kgs.12-610 52270 5/16 I 2-1/8 11/16 1/2 1/4 1-21/32 9/32 1-5/8 .11 .0512-612 52271 3/8 I 2-1/8 11/16 5/8 9/32 1-5/8 11/32 1-5/8 .12 .0512-614 52272 7/16 II 2-1/8 11/16 21/32 11/32 1-5/8 11/32 1-5/8 .13 .0612-616 52273 1/2 II 2-1/8 3/4 3/4 3/8 1-15/32 7/16 — .17 .0812-618 52274 9/16 II 2-3/8 13/16 13/16 7/16 1-1/2 17/32 — .19 .0912-620 52275 5/8 II 2-1/8 29/32 29/32 15/32 1-1/2 5/8 — .24 .1112-622 52276 11/16 II 2-5/8 31/32 31/32 1/2 1-19/32 21/32 — .26 .1212-624 52277 3/4 II 2-5/8 1-1/16 1-1/16 9/16 1-19/32 23/32 — .28 .1312-626 52278 13/16 II 2-3/4 1-1/8 1-1/8 9/16 1-25/32 25/32 — .33 .1512-628 52279 7/8 II 2-3/4 1-3/16 1-3/16 19/32 1-7/8 27/32 — .36 .1612-630 52280 15/16 II 2-3/4 1-9/32 1-9/32 19/32 1-15/16 29/32 — .41 .1912-632 52281 1 II 2-3/4 1-11/32 1-11/32 5/8 2 1 — .46 .213/8" Drive Metric Impact SocketsMetric Impact Sockets,Standard Length, 6 Point• Designed for power and impactuse, the flank drive design providesless stress on the cornersof the socket.Williams ToolsType IIMetric Impact Sockets, Deep Length, 6 Point• Flank design reduces the possibility offastener rounding.• Deep length sockets most commonly usedto access recessed fasteners.BoltCat. EDP Size A B C D E Clear. FNo. No. (mm) Type (in) (in) (in) (in) (in) Dia. (in) Lbs. Kgs.12M-607 52249 7 I 2-1/8 11/16 7/16 9/32 1-11/16 1/4 1-5/8 .11 .0512M-608 52250 8 I 2-1/8 11/16 1/2 1/4 1-11/16 9/32 1-5/8 .11 .0512M-609 52224 9 I 2-1/8 11/16 9/16 9/32 1-11/16 11/32 1-5/8 .12 .0512M-610 52251 10 I 2-1/8 11/16 5/8 9/32 1-11/16 11/32 1-5/8 .13 .0612M-611 52226 11 II 2-1/8 11/16 21/32 21/64 1-11/16 11/32 1-5/8 .13 .0612M-612 52227 12 II 2-1/8 23/32 23/32 3/8 1-23/32 7/16 — .14 .0612M-613 52252 13 II 2-1/8 25/32 25/32 7/16 1-3/8 15/32 — .18 .0812M-614 52228 14 II 2-3/8 13/16 13/16 13/32 1-9/16 1/2 — .18 .0812M-615 52253 15 II 2-3/8 27/32 27/32 13/32 1-9/16 9/16 — .18 .0812M-616 52229 16 II 2-3/8 29/32 29/32 13/32 1-9/16 19/32 — .19 .0912M-617 52230 17 II 2-5/8 31/32 31/32 7/16 1-3/4 5/8 — .24 .1112M-618 52231 18 II 2-5/8 1 1 7/16 1-3/4 11/16 — .26 .1212M-619 52232 19 II 2-5/8 1-1/16 1-1/16 9/16 1-3/4 23/32 — .28 .1312M-621 52233 21 II 2-5/8 1-5/32 1-5/32 1/2 1-3/4 25/32 — .37 .1712M-624 52234 24 II 2-7/8 1-5/16 1-5/16 19/32 1-31/32 29/32 — .41 .191/2" Drive Impact ToolsImpact ExtensionFed. Spec.: GGG-W-660A; ANSI B107.2• Square drive supplied with spring plunger.Cat. EDP Length Square SquareNo No. (in) Female (in) Male (in) Lbs. Kgs.4-102 56429 3-1/2 1/2 1/2 .20 .094-105A 53176 5 1/2 1/2 .30 .144-110A 53181 10 1/2 1/2 .41 .19Impact AdapterFed. Spec.: GGG-W-660A; ANSI B107.2• The 4-5A adapter is supplied with a spring plunger in the male drive.• The 4-6 adapter has a thru pin hold which should be used with a retainerpin and O-ring or Williams RET RING ® .Cat. EDP Square Square Lgth.No No. Female (in) Male (in) (in) Lbs. Kgs.4-2A 52075 1/2 3/8 2-1/4 .15 .074-6 51085 1/2 3/4 1-1/4 .30 .14Impact Universal JointFed. Spec.: GGG-W-660A; ANSI B107.2• Unique design supplied with a sleeve over theball area to provide maximum safety.Cat. EDP Square Square Lgth.No No. Female (in) Male (in) (in) Lbs. Kgs.4-140B 53509 1/2 1/2 2-1/4 .62 .30Type IType II19Hand ToolsBolt.Cat. EDP Size A B C D E Clear. FNo. No. (mm) Type (in) (in) (in) (in) (in) Dia. (in) Lbs. Kgs.2M-607 54336 7 I 1-1/32 11/16 7/16 7/32 9/16 1/4 17/32 .08 .042M-608 52254 8 I 1-1/32 11/16 1/2 1/4 9/16 9/32 17/32 .08 .042M-609 54338 9 I 1-1/32 11/16 9/16 9/32 9/16 11/32 17/32 .06 .032M-610 52255 10 I 1-1/32 11/16 5/8 9/32 9/16 11/32 17/32 .07 .032M-611 54340 11 I 1-1/32 11/16 21/32 9/32 19/32 11/32 9/16 .08 .042M-612 54341 12 II 1-1/16 23/32 23/32 9/32 9/16 11/32 — .10 .052M-613 52256 13 II 1-1/16 25/32 25/32 9/32 19/32 3/8 — .08 .042M-614 54343 14 II 1-3/32 13/16 13/16 9/16 19/32 1/2 — .13 .062M-615 52257 15 II 1-3/32 27/32 27/32 9/16 19/32 9/16 — .11 .052M-616 54362 16 II 1-1/8 29/32 29/32 19/32 5/8 19/32 — .16 .072M-617 54344 17 II 1-5/32 31/32 31/32 19/32 5/8 5/8 — .19 .092M-618 54363 18 II 1-5/32 1 1 5/8 21/32 11/16 — .17 .082M-619 52258 19 II 1-3/16 1-1/16 1-1/16 21/32 11/16 23/32 — .17 .0819-198WWW.HANESSUPPLY.COM