10 table saw - Grizzly Industrial Inc.

Safety Instructions For Power Tools9. USE PROPER EXTENSION CORD. Makesure your extension cord is in good condition.Conductor size should be in accordancewith the chart below. The amperagerating should be listed on the motor or toolnameplate. An undersized cord will cause adrop in line voltage resulting in loss of powerand overheating. Your extension cord mustalso contain a ground wire and plug pin.Always repair or replace extension cords ifthey become damaged.Minimum Gauge for Extension CordsLENGTHAMP RATING 25ft 50ft 100ft0-6 18 16 167-10 18 16 1411-12 16 16 1413-16 14 12 1217-20 12 12 1021-30 10 10 No10. WEAR PROPER APPAREL. Do not wearloose clothing, gloves, neckties, rings,bracelets, or other jewelry which may getcaught in moving parts. Non-slip footwear isrecommended. Wear protective hair coveringto contain long hair.16. REDUCE THE RISK OF UNINTENTION-AL STARTING. On machines with magneticcontact starting switches there is arisk of starting if the machine is bumped orjarred. Always disconnect from powersource before adjusting or servicing. Makesure switch is in OFF position before reconnecting.17. MANY WOODWORKING TOOLS CAN“KICKBACK” THE WORKPIECE towardthe operator if not handled properly. Knowwhat conditions can create “kickback” andknow how to avoid them.18. CHECK DAMAGED PARTS. Before furtheruse of the tool, a guard or other partthat is damaged should be carefullychecked to determine that it will operateproperly and perform its intended function.Check for alignment of moving parts, bindingof moving parts, breakage of parts,mounting, and any other conditions thatmay affect its operation. A guard or otherpart that is damaged should be properlyrepaired or replaced.19. NEVER LEAVE TOOL RUNNING UNAT-TENDED. TURN POWER OFF. Do notleave tool until it comes to a complete stop.11. ALWAYS USE SAFETY GLASSES. Also useface or dust mask if cutting operation is dusty.Everyday eyeglasses only have impact resistantlenses, they are NOT safety glasses.12. SECURE WORK. Use clamps or a vise to holdwork when practical. It’s safer than using yourhand and frees both hands to operate tool.13. DO NOT OVER-REACH. Keep proper footingand balance at all times.14. MAINTAIN TOOLS WITH CARE. Keeptools sharp and clean for best and safestperformance. Follow instructions for lubricatingand changing accessories.15. USE RECOMMENDED ACCESSORIES.Consult the owner’s manual for recommendedaccessories. The use of improperaccessories may cause risk of injury.20. NEVER OPERATE A MACHINE WHENTIRED, OR UNDER THE INFLUENCE OFDRUGS OR ALCOHOL. Full mental alertnessis required at all times when runninga machine.21. NEVER ALLOW UNSUPERVISED ORINEXPERIENCED PERSONNEL TOOPERATE THE MACHINE. Make sureany instructions you give in regards tomachine operation are approved, correct,safe, and clearly understood.22. IF AT ANY TIME YOU ARE EXPERIENC-ING DIFFICULTIES performing the intendedoperation, stop using the machine!Then contact our service department orask a qualified expert how the operationshould be performed.G1022 Series Contractor Saws -3-

Additional Safety Instructions For Table Saws1. ALWAYS use blade guard, splitter andanti-kickback fingers on all ''through-sawing''operations. Through-sawing operationsare those when the blade cuts completelythrough the workpiece as in rippingor crosscutting.2. AVOID KICKBACKS. A condition in whicha piece of wood is thrown back towards anoperator at a high rate of speed. If you donot have a complete understanding of howkickback occurs, or how to prevent it, DONOT operate this table saw.3. NEVER reach behind or over the bladewith either hand for any reason.4. ALWAYS use a push stick for ripping narrowstock.5. NEVER perform any operation ''freehand,''which means using only your handsto support or guide the workpiece. Alwaysuse either the fence or the miter gauge toposition and guide the work.6. NEVER stand or have any part of yourbody in line with the path of the saw blade.7. ALWAYS hold the work firmly against themiter gauge or fence and hold the workfirmly against the table.8. MOVE the rip fence out of the way whencrosscutting.9. NEVER use the miter gauge and rip fenceat the same time.10. NEVER attempt to free a stalled saw bladewithout first turning the saw OFF.11. PROVIDE adequate support to the rearand sides of the saw table for wide or longworkpieces.12. AVOID awkward operations and handpositions where a sudden slip could causeyour hand to move into the blade.13. IF AT ANY TIME YOU ARE EXPERIENC-ING DIFFICULTIES performing the intendedoperation, stop using the machine!Then contact our service department orask a qualified expert how the operationshould be performed.14. ALWAYS LOWER OR REMOVE SAWBLADE WHEN NOT IN USE.15. NEVER USE A DAMAGED SAW BLADEOR ONE THAT HAS BEEN DROPPED.16. USE GREAT CARE WHEN CUTTINGWITH A DADO BLADE. There is a highdegree of risk involved with any dado operation.Slight movement of the stock awayfrom the fence will cause kickback.No list of safety guidelines can be complete.Every shop environment is different.Always consider safety first, as it applies toyour individual working conditions. Usethis and other machinery with caution andrespect. Failure to follow guidelines couldresult in serious personal injury, damage toequipment or poor work results.-4- G1022 Series Contractor Saws

Statistics prove that most common accidentsamong table saw users can belinked to kickback. Kickback is typicallydefined as the high-speed expulsion ofstock from the table saw toward its operator.In addition to the danger of the operatoror others in the area being struck bythe flying stock, it is often the case thatthe operator’s hands are forced into theblade during the kickback. The followingcan help minimize kickbacks.1. Use your blade guard and splitter.2. Never for any reason place your handbehind the blade. Should kickbackoccur, your hand will be pulled into theblade.3. Inspect splitter for alignment between itand your blade.4. Never use the fence as a guide for crosscutting.5. Never attempt freehand cuts.6. Use a push stick or featherboard tomaintain control of your workpiece.7. Feed cuts through to completion.8. Stand to the side when ripping.9. Ensure your fence and miter slot are parallelto the blade.If you do not have a clear understanding ofkickback and how it occurs, do not operatethis table saw.Safety AccessoriesPush SticksThe use of push sticks, particularly when cuttingsmall or narrow workpieces, provides a doublebenefit for saw operators. The push stick providesadded leverage, enabling the operator tokeep the workpiece firmly supported against thefence and table. At the same time, the push stickkeeps the operator’s hand safely away from therotation of the saw blade as shown in Figure 1.See the template on Page 62 of the manual forconstruction details, or purchase one from theGrizzly catalog.Push StickFigure 1. Push Stick.Zero Clearance Table InsertsIdeal for use when ripping thin strips or makingbevel cuts, these prevent tearout and jammedblades by supporting material close to the blade.Use the standard table insert as a template whencreating additional inserts from wood or plywood.Blade slot inserts can be custom cut for specificblade angles by raising the running blade into anuncut insert at the angle you desire. Be sure tomake an additional slot for the blade splitter. Wealso carry a wide selection of table inserts shownin Figure 2 in the Grizzly catalog. Be sure to holdthe insert firmly in place with a piece of woodwhen creating slots. Never hold the table insertwith your hand while cutting new slots.G1022 Series Contractor Saws -5-

SECTION 2: CIRCUIT REQUIREMENTS110V OperationThe Model G1022SM, Z and ZF motors areprewired to operate at 110V. See Figure 5 for atypical 110V installation.G1022SM and G1022Z:Under normal 110V use, the Models G1022SMand Z motors draw approximately 16 amps. Werecommend a 20 amp circuit breaker or a 20 ampslow-blow fuse.G1022ZF:Under normal 110V use, the Model G1022ZFmotor draws approximately 17 amps. We recommenda 20 amp circuit breaker or a 20 amp slowblowfuse.Figure 5. Typical 110V 3-prong plug and outlet.The circuit you use should be dedicated, (i.e., themachine should provide the only draw from thatcircuit). If frequent circuit failures occur whenusing this machine, contact our ServiceDepartment or your local electrical contractor.Because of the high amperage draw of the ModelG1022 Series when wired for 110V, standardhousehold circuit wiring may not be of a largeenough gauge. A qualified electrician may need toinstall a new circuit with wires capable of handlinga 20 amperage draw. Do not attempt to modify anexisting circuit by replacing the circuit breakerwith one rated for a higher amperage.-8- G1022 Series Contractor Saws

220V OperationG1022ZFX and G1022PRO:The motors supplied with the Models G1022ZFXand G1022PRO are prewired to operate at 220V.The Models G1022ZFX and G1022PRO are notsupplied with a plug; therefore, a suitable 220Vplug must be wired in. When operating at 220V,we recommend using a NEMA-style 6-15 plugand outlet as shown in Figure 6A. You may also“hard-wire” the machine directly to your panel,provided you place a disconnect switch near themachine. Check the electrical codes in your areafor specifics on wiring requirements.Figure 6A. Typical 220V 3-prong plug and outlet.Under normal use, the motor draws approximately13 amps at 220V. We recommend a 15 amp circuitbreaker for 220V operation. This should besatisfactory for normal use while providingenough protection against circuit damage causedby power surges. Always check to see if your currentwires are capable of handling a 15 amp load.If you are unsure, consult the advice of a qualifiedelectrician. Do not attempt to modify an existingcircuit by replacing the circuit breaker with onerated for a higher amperage.G1022 Series Contractor Saws -9-

GroundingExtension CordsIn the event of an electrical short, grounding provideselectric current a path of least resistance toreduce the risk of electrical shock. This tool isequipped with an electric cord having an equipment-groundingconductor which must be properlyconnected to a grounding plug. The plug mustbe plugged into a matching outlet that is properlyinstalled and grounded in accordance with alllocal codes and ordinances.Improper connections of the electrical-groundingconductor can result in risk of electric shock. Theconductor with green or green and yellow stripedinsulation is the electrical-grounding conductor. Ifrepair or replacement of the electric cord or plugis necessary, do not connect the equipmentgrounding conductor to a live terminal.We do not recommend the use of extension cordswith 220V equipment. It is much better to arrangethe placement of your equipment and the installedwiring to eliminate the need for extension cords.Should it be necessary to use an extension, makesure the cord is rated Hard Service (grade S) orbetter. Refer to the chart in Section 1: SafetyInstructions to determine the minimum gauge forthe extension cord when using either 110V or220V. The extension cord must also contain aground wire and plug pin. Always repair or replaceextension cords when they become worn or damaged.This equipment must begrounded. Verify that anyexisting electrical outletand circuit you intend toplug into is actuallygrounded. Under no circumstancesshould thegrounding pin from anythree-pronged plug beremoved. Serious injurymay occur.We have covered some basic electricalrequirements for the safe operation of yourmachine. These requirements are not necessarilycomprehensive. You must be surethat your particular electrical configurationcomplies with local and state codes.Ensure compliance by checking with yourlocal municipality or a licensed electrician.-10- G1022 Series Contractor Saws

SECTION 3: INTRODUCTIONItem G1022SM G1022Z G1022ZF G1022ZFX G1022PROExtensionWingsSheet MetalCast IronCast IronCast IronCast IronRip FenceStandardT-Slot FenceShop Fox ®Shop Fox ®Shop Fox ® ClassicMiter GaugeStandardStandard OrangeAdjustable SlotAdjustable SlotAdjustable SlotMotor1.5 H.P.-110/220V1.5 H.P.-110/220V1.5 H.P.-110/220V2 H.P.-110/220V2H.P.-110/220VPre-Wired110V110V110V220V220VSwitchBody MountedBody MountedRail MountedRail MountedRail MountedWeight220 lbs250 lbs290 lbs290 lbs340 lbsDust Port--4" Port4" Port4" PortCommentaryWe are proud to offer the Model G1022 SeriesTable Saws. The Model G1022 Series is part of agrowing Grizzly family of fine woodworkingmachinery. When used according to the guidelinesset forth in this manual, you can expectyears of trouble-free, enjoyable operation andproof of Grizzly’s commitment to customer satisfaction.The Model G1022 Series comes in 5 different versions.The differences are listed on the chart atthe beginning of this manual. The SM, Z, ZF, ZFXand PRO are all 10" heavy-duty table sawsdesigned for a wide variety of cutting applications.They feature ball bearing arbors on a worm gearmechanism, precision-ground cast iron tables(except the Model G1022SM), sturdy steelstands, standard and dado inserts and a mitergauge.We also offer many accessories for the tablesaws including blades, extension rails, outfeedrollers and a mobile base. Please refer to our currentcatalog for prices and ordering information.We are also pleased to provide this manual withthe Model G1022 Series. It was written to guideyou through assembly, review safety considerations,and cover general operating procedures. Itrepresents our effort to produce the best documentationpossible. If you have any commentsregarding this manual, please write to us at theaddress below:Grizzly Industrial, Inc.C/O Technical DocumentationP.O. Box 2069Bellingham, WA 98227-2069G1022 Series Contractor Saws -11-

Most importantly, we stand behind our machines.If you have any service questions or partsrequests, please call or write us at the locationlisted below:Grizzly Industrial, Inc.1203 Lycoming Mall CircleMuncy, PA 17756Phone: (570) 546-9663Fax: (800) 438-5901E-Mail: techsupport@grizzly.comWeb Site: http://www.grizzly.comThe specifications, drawings, and photographsillustrated in this manual represent the ModelG1022 Series as supplied when the manual wasprepared. However, owing to Grizzly’s policy ofcontinuous improvement, changes may be madeat any time with no obligation on the part ofGrizzly. Whenever possible, though, we sendmanual updates to all owners of a particular toolor machine. Should you receive one, we urge youto insert the new information with the old and keepit for reference.Read the manual beforeassembly and operation.Become familiarwith the machine and itsoperation before beginningany work. Seriouspersonal injury mayresult if safety or operationalinformation is notunderstood or followed.-12- G1022 Series Contractor Saws

UnpackingPiece InventoryThe Model G1022 Series is shipped from themanufacturer in a carefully packed carton. If youdiscover the machine is damaged after you havesigned for delivery, immediately call CustomerService for advice.When you are completely satisfied with the conditionof your shipment, you should inventory itsparts.If moving this machineup or down stairs, themachine must be dismantledand moved insmaller pieces. Makesure floor and stairstructures are capable ofsupporting the combinedweight of themachine parts and thepeople moving them.After all the parts have been removed from the carton,you should have:1. Stand Components2. Extension Wings (2)3. V-Belt4. Motor with Pulley5. Motor Bracket6. Motor Mount Plate7. Table Saw Unit8. Handwheels (2)9. Arbor Wrench10. Dado Insert11. Standard Insert12. Miter Gauge14. Blade Guard15. Blade Guard Bracket16. Hardware Bags (5)17. V-Belt Guard and Mounting Hardware18. V-Belt Guard Bracket19. Fence Unit (Separate Box W/ZF, ZFX and Pro)20. Fence Rails (Separate Box)The Model G1022 Seriesrepresents a heavy load.Seek assistance beforebeginning assembly.Some metal parts mayhave sharp edges onthem after they areformed. Please examinethe edges of all metalparts before handlingthem. Failure to do socould result in injury.20211979Figure 6B. (G1022 Layout) Rip fence, rails andextension wings will vary depending on model.111015 312864161714185G1022 Series Contractor Saws -13-

Hardware ContentsGuide Rail & Extension Wing Hardware BagPlastic Belt Guard Hardware BagQty Description8 Special Rail Bolt (SM & Z)8 Fence Rail Spacer (SM & Z)4 Flat Washer M10 (SM & Z)4 Hex Nut M10-1.5 (SM & Z)4 Fence Rail Plug (SM & Z)6 Flat Washer M10 x M4 Thick6 Hex Bolt M10-1.5 x 252 Hand Wheel KnobFloor Stand Hardware BagQty Description40 Carriage Bolt M8-1.25 x 164 Hex Bolt M8-1.25 x 1948 Flat Washer M844 Hex Nut M8-1.254 Hex Bolt M10-1.5 x 204 Hex Nut M10-1.54 Flat Washer M104 Plastic Foot4 Hex Bolt #10-24 x 3 ⁄8" (ZX, ZFX, PRO)4 Hex Nut #10-24 (ZX, ZFX, PRO)4 Lock Washer #10 (ZX, ZFX, PRO)Qty Description1 Hex Bolt 1 ⁄4"-20 x 2"1 Flat Washer 1 ⁄4"1 Sleeve1 Wing Nut 1 ⁄4"-201 Plastic Belt GuardMotor Mount Hardware BagQty Description4 Hex Bolt M8-1.25 x 258 Flat Washer M84 Hex Nut M8-1.25In the event that any nonproprietary parts aremissing (e.g. a nut or a washer), we would beglad to replace them, or for the sake of expediency,replacements can be obtained at your localhardware store.-14- G1022 Series Contractor Saws

Hardware Recognition ChartUse this chart to match uphardware pieces during theassembly process!MEASURE BOLT DIAMETER BY PLACING INSIDE CIRCLE4mm6mm8mm10mm12mm16mm#101⁄4''5⁄16''3⁄8''7⁄16''1⁄2''5⁄8''LINES ARE 1MM APARTThumbScrewCapScrewSetscrewWasher5mm10mm15mm20mm25mm30mm35mm40mm45mm50mm55mm60mm65mm70mm75mm1⁄4''3⁄8''1⁄2''5⁄8''PhillipsHeadScrewCarriageBoltHexHeadBoltLockWasherLINES ARE 1 ⁄16'' INCH APARTLockNutCountersunkPhillipsHeadScrewHexNut5⁄16''7⁄16''9⁄16''3⁄4''7⁄8''1''1 1 ⁄4''1 1 ⁄2''1 3 ⁄4''22 1 ⁄4''2 1 ⁄2''2 3 ⁄4''3FlangeBoltPhillipsHeadHexBoltWASHERS ARE MEASURED BY THE INSIDE DIAMETERWingNut12mmSlottedScrewWASHER DIAMETER10mmWASHER DIAMETER8mmWASHER DIAMETERButtonHeadScrewPhillipsHeadSheetMetalScrew4mm6mmIWASHER D AMETERASHER DIAMETERW5⁄ 8''9⁄16''WASHER DIAMETER1⁄2''WASHER DIAMETER7⁄16''WASHER DIAMETER3⁄8''WASHER DIAMETER5⁄16''1⁄4''#10IWASHER D AMETERIWASHER D AMETERIWASHER D AMETERIWASHER D AMETERG1022 Series Contractor Saws -15-

Clean UpThe unpainted surfaces are coated with a waxy oilto protect them from corrosion during shipment.Remove this protective coating with a solventcleaner or citrus-based degreaser such asGrizzly’s G7895 Degreaser. Avoid chlorine-basedsolvents as they may damage painted surfacesshould they come in contact. Always follow theusage instructions on the product you choose forclean up.Do not use gasoline orother petroleum-basedsolvents. They have lowflash points which makethem extremely flammable.A risk of explosionand burning exists ifthese products areused. Serious personalinjury may occur if thiswarning is ignored.Do not smoke while usingsolvents. A risk of explosionor fire exists and mayresult in serious personalinjury.Many of the solventscommonly used to cleanmachinery can be toxicwhen inhaled or ingested.Always work in wellventilatedareas far frompotential ignition sourceswhen dealing with solvents.Use care when disposingof waste rags andtowels to be sure they donot create fire or environmentalhazards.Site ConsiderationsFLOOR LOADYour Model G1022 Series represents a mediumload in a small footprint. Most commercial orhome shop floors should be sufficient to carry theweight of the Model G1022 Series. If you questionthe strength of your floor, you can opt to reinforceit.WORKING CLEARANCESWorking clearances can be thought of as the distancesbetween machines and obstacles thatallow safe operation of every machine without limitation.Consider existing and anticipated machineneeds, size of material to be processed througheach machine, and space for auxiliary standsand/or work tables. Also, consider the relativeposition of each machine to one another for efficientmaterial handling. Be sure to allow yourselfsufficient room to safely run your machines in anyforeseeable operation and keep dust collectionhoses off the floor and out of the way.LIGHTING AND OUTLETSLighting should be bright enough to eliminateshadows and prevent eye strain. Electrical circuitsshould be dedicated or large enough to handlecombined motor amp loads. Outlets should belocated near each machine so power or extensioncords are not obstructing high-traffic areas. Besure to observe local electrical codes for properinstallation of new lighting, outlets, or circuits.Make your shop “childsafe.” Ensure that yourworkplace is inaccessibleto youngsters by closingand locking all entranceswhen you are away. Neverallow visitors in your shopwhen assembling, adjustingor operating equipment.-16-G1022 Series Contractor Saws

SECTION 4: ASSEMBLYBeginning AssemblyStand Assembly!Disconnect power to themachine when performingany maintenance,assembly or adjustments.Failure to do thismay result in seriouspersonal injury.The Model G1022 Series is supplied with aheavy-duty stand. To assemble the stand:1. Fasten the plastic feet to all four legs usingthe M10-1.5 x 25 hex bolts, 10MM flat washersand M10-1.5 hex nuts as shown inFigure 7.Keep loose clothingrolled up and out of theway of machinery andkeep hair pulled back.Wear safety glasses duringthe entire assemblyprocess. Failure to complymay result in seriouspersonal injury.Some metal parts mayhave sharp edges onthem after they areformed. Please examinethe edges of all metalparts before handlingthem. Failure to do socould result in injury.Most of your Model G1022 Series has beenassembled at the factory, but some parts must beassembled or installed after delivery. We haveorganized the assembly process into steps.Please follow along in the order presented here.Figure 7. Installing the rubber feet.2. Locate the long upper and lower side braces(2 each) and bolt to the legs using the M8-1.25 x 16 carriage bolts, 8MM flat washersand M8-1.25 hex nuts as shown in Figure 8.Do not tighten any stand bolts at this time.TOOLS REQUIRED: High quality square andstraightedge, metric Allen ® wrench set, flat screwdriver,Phillips ® screwdriver, dead blow hammerand a 6" or 8" adjustable wrench.G1022 Series Contractor SawsFigure 8. Assembled side panel.-17-

3. Attach the short upper and lower side bracesto one of the assembled side panels. Use theM8 - 1.25 x 16 carriage bolts, 8MM flat washersand M8-1.25 hex nuts as shown inFigure 9.6. Note the location of the mounting holes onthe top of the stand. Turn the table saw bodyupside-down and place the dust hood andadapter assembly over the bottom of thetable saw body with the dust port flangepointed up.All Models:7. Align the holes at the four corners. Place theassembled stand upside down on the tablesaw body, and line up its mounting holes.Make certain the side of the stand with the “ZSeries” label, if applicable, is on the front sideof the machine (the side with the Grizzly labeland angle scale). Secure with M8-1.25 x 19hex bolts, 8MM flat washers and M8-1.25hex nuts, with the dust port sandwichedbetween as shown in Figure 11.Figure 9. Assembled stand section.4. Bolt the other side panel to the upper andlower braces using the M8-1.25 x 16 carriagebolts, 8MM flat washers and M8-1.25hex nuts as shown in Figure 10.Saw BodyDust HoodAdapterDust HoodStandFigure 11. Attaching the stand to the saw base.Figure 10. Stand completely assembled.8. With the help of a second person, flip theentire table saw unit right side-up and moveit into its working position. Level the stand bychecking all sides for symmetry. Measurediagonally from top to bottom and adjust thestand so both diagonals are equal. Tightenall of the stand bolts.G1022ZF and ZFX:5. Take the black plastic dust hood with the 4"port and align it with the opening in theadapter. The bolt holes on each of the fourcorners should line up. Using 10-24 x 3 ⁄8"bolts, 10-24 nuts and 3 ⁄16" lock washers tosecure the hood to the adapter.-18- G1022 Series Contractor Saws

HandwheelsMotorTo mount the handwheels:1. Position a handwheel over the arbor raisingshaft on the front of the saw. Be sure it fitscompletely over the shaft. The slots in thehandwheel hole will engage with the roll pinon the shaft as shown in Figure 12.2. Position the other handwheel similarly on theblade tilting shaft located at the side of thesaw.3. Screw the black plastic lock knobs onto theends of the shafts to lock the handwheels inplace.The following pictures show the motor and V-beltincluded with the Model G1022SM and Z. Themotor and belt included with the Model G1022ZF,ZFX and PRO will look slightly different but willassemble in the same manner as shown.To mount the motor:1. Turn the motor upside down and attach themotor plate using M8-1.25 x 25 hex bolts,8MM flat washers and M8-1.25 hex nuts asshown in Figure 13. Finger-tighten only.Roll PinNote: Motor comespre-wired.Body mounted switch onG1022SM and Z onlyFigure 12. Mounting the handwheels.Figure 13. Attaching the motor plate.2. Insert the 1 ⁄4''-20 x 2'' hex bolt through thehole in the pulley guard bracket as shown inFigure 14.Figure 14. Attaching pulley guard bracket.G1022 Series Contractor Saws -19-

3. Set the motor on end and slip the pulleyguard bracket between the base of the motorand the motor plate. Tighten one of the fourmounting bolts. Leave the other three looseas shown in Figure 15.5. Turn the arbor tilting handwheel until thearbor is set to 0°. Slide the motor assemblyonto the linking bars through the holes in themotor bracket. Line up the setscrews withthe grooves on the linking bars and tightenas shown in Figure 17.Figure 15. Installing pulley guard.4. Locate the motor mount bracket. Loosen thesetscrew that holds the motor pivot rod inplace and remove the rod. Line up the holein the motor bracket with the hole in themotor plate and insert the motor pivot rodmaking sure the groove in the rod lines upwith the setscrew in the mount bracket asshown in Figure 16. Tighten the setscrew.Figure 17. Attaching motor to linking bars.6. Lift the motor up and slip the V-belt over thegrooves in the pulleys. Slowly release themotor, allowing its weight to add tension tothe V-Belt as shown in Figure 18.Figure 18. Attaching the V-belt to the motor.Figure 16. Installing the motor mount bracket.-20- G1022 Series Contractor Saws

7. Place a straightedge across the arbor pulleyand the motor pulley. The straightedgeshould run across both pulleys evenly asshown in Figure 19. Adjust the motor on itsmount until pulleys are aligned, then tightenall the mounting bolts.WiringG1022SM and G1022Z:The ON/OFF switch, with attached power cordand plug, is already mounted to the saw enclosure.Simply connect the quick disconnect on thecord between the switch and motor.G1022ZF, G1022ZFX and G1022PRO:The ON/OFF switch on the ZF, ZFX and PROmodels mounts directly below the front fence rail.1. Take the L-shaped bracket supplied andposition it below the front fence rail at the lefthand side of the machine. The shorter sideof the L has two holes which will align withtwo holes in the fence rail. Use two Philip ®head screws to attach the bracket. Threadthem in from underneath the rail so theheads are not in the way of the fence travel.Figure 19. Checking V-belt alignment.8. Slip the pulley cover spacer over the pulleycover mounting bolt and fit the plastic pulleycover in place. Secure it with the wing nutprovided as shown in Figure 20.2. Now attach the switch, using two Philips ®head screws inserted through the back of thebracket and into threaded inserts in the backside of the switch box. Tighten these so theswitch box is secure.3. Connect the quick disconnect on the cordbetween the switch and motor.Figure 20. Attaching the pulley guard.G1022 Series Contractor Saws -21-

Extension WingsThe Model G1022SM is supplied with sheet metalextension wings, and the Models G1022Z, ZF,ZFX and PRO include cast iron extension wings.Installation and adjustment are the same for allthe models. To install the extension wings:1. Attach each wing to the table using the M10- 1.50 x 25 hex bolts and 10MM flat washersprovided. Thread the center bolt in first, thenthe front and back bolts. Get the wings reasonablyflush with the table. Do not completelytighten the bolts.2. Working front to back, align the front edge ofthe extension wing with the edge of the table,so they are flush, and tighten the front bolt.3. Raise or lower the rear of the extension winguntil the middle of the wing is flush with thetable top and tighten the middle bolt asshown in Figure 21.6. Now, check the alignment of the table vs.both wings. Your straightedge should run flatacross both wings and the table top. If thestraightedge contacts both the wings and thetable evenly, you may skip to the next section.If it does not, continue to Step 7.7. If the wings tilt down, apply layers of maskingtape under each bolt near the bottomedge of the wing.8. If the wing tilts up, apply layers of maskingtape above each bolt near the top edge ofthe wing.9. Tighten bolts and adjust again as describedin Steps 2-4.Fence RailsG1022SM and G1022ZThe Model G1022SM and Z are supplied withround rails, the Model G1022ZF and ZFX aresupplied with flat angular bar sections and theModel G1022PRO is supplied with square tuberails. This accommodates the standard fence forthe SM and Z models, the Shop Fox ® fence forthe ZF and ZFX models and the Shop Fox ®Classic fence for the PRO model. Please refer tothe Shop Fox ® manuals for complete informationregarding the installation of the front and backfence rails on the ZX, ZXF and PRO models.The rails should extend to the right of the saw andare attached to the table top with special boltsand dished spacers. The rails come packed in aseparate box. To mount the rails:Figure 21. Checking table to wing alignment.4. Raise or lower the rear of the wing until thewing and table are flush. Tighten the bolt.5. Repeat Steps 2-4 for the other extensionwing.1. The two center bolts for each rail threaddirectly into the table top, and the outer twobolts secure from the back side of the extensionwing with hex nuts as shown in Figure22. Be sure that the rail with the built-in measuringrule is mounted on the front side of themachine, with the markings facing up.2. Insert the round, plastic plugs into the endsof each rail.-22- G1022 Series Contractor Saws

BladePlease refer to our current catalog for a completeselection of saw blades. To install the saw blade:1. Unthread the arbor nut clockwise andremove the outside flange from the arbor.Note that there is a 3 ⁄4'' diameter spacer onthe arbor shaft. Remove and discard it.Remember the arbor nut is a left-handedthread.Figure 22. Attaching fence rails.FenceG1022SM and G1022Z2. Install the saw blade onto the arbor. Ensurethat the blade teeth point toward you as youstand at the front of the saw. Slide on theflange and thread the arbor nut back on.3. Use the arbor wrench provided with the sawto tighten the arbor nut. Wedge a block ofwood in the teeth of the blade to keep it fromturning when tightening the nut as shown inFigure 24.1. Thread the plastic knob onto the lock handle.2. Set the lock handle in the up position andslide the fence over the front and rear rails asshown in Figure 23.Lock HandleFigure 24. Changing saw blade.Figure 23. G1022SM fence shown.3. The fence will require further adjustments, allof which are covered in AdjustmentsSection.!Disconnect power to themachine when performingany maintenance,assembly or adjustments.Failure to do thismay result in seriouspersonal injury.G1022 Series Contractor Saws -23-

Blade Guard1. Screw the threaded end of the support shaftinto the hole in the back of the rear trunnion.The check nut on the shaft will be used totighten the shaft in place as shown in Figure25. Leave it loose for now.4. Tighten the mounting bolts to secure theblade guard.5. Using a machinist's or a combination square,align the face of the splitter perpendicular tothe surface of the saw table as shown inFigure 27. Rotate the support shaft slightly.This will normally correct any minor misalignment.Figure 25. Installing blade guard.2. Loosen the blade-guard mounting bolt locatedjust inside the table cut-out and the bladeguard mounting bolt on the end of the supportshaft.3. Slip the slots at the bottom of the guard overthe two mounting bolts as shown in Figure26. The washers should be between the bolthead and the slots. Rotate the support shaftto align the mounting bolts to the mountingslots on the guard.Support ShaftFigure 27. Adjusting blade guard.The saw blade is extremely sharp. Use extracare when handling the blade or workingnear it. Serious injury is possible.6. Next, set a straightedge against the face ofthe saw blade and the blade guard/splitter asshown in Figure 28. If the blade guard/splitteris properly aligned, please skip ahead tothe next section; otherwise, continue with thenext step.Blade Guard Mounting BoltsSupport ShaftBlade GuardFigure 26. Blade guard components.-24- G1022 Series Contractor Saws

Figure 28. Checking alignment of blade guard.7. If the blade guard/splitter is to the right of theblade as shown in Figure 29. simply addwashers between the splitter and frontmounting bracket, and adjust the rear splittersupport as shown in Figure 29.Figure 30. Proper splitter/blade alignment.8. Recheck guard alignment to the blade and tothe table top. Adjust as necessary and tightenall the bolts before use. If the blade guardis properly aligned, please skip ahead to thenext section; otherwise, continue with thenext step.9. If the splitter is positioned to the left of theblade, alignment cannot be achieved bywasher placement. Adjustment of the frontsupport bracket is required as shown inFigure 30. Loosen the adjustment screwsand move to the right.10. Recheck guard alignment to the blade and tothe table top. Adjust as necessary and tightendown all the bolts before use.Figure 29. Improper splitter/blade alignment.11. Adjust the blade to 45° and raise and lower itthrough the full range. Readjust blade to 90°and raise and lower it through the full range.There should be no contact between thebase and the table insert or any other part ofthe saw. If there is, repeat Steps 1-10.G1022 Series Contractor Saws -25-

Table Insert!Disconnect power to themachine when performingany maintenance,assembly or adjustments.Failure to do thismay result in seriouspersonal injury.Allen ® WrenchSetscrewThe table insert provides access to the blade andarbor when removed. When in place, the insertprovides support for materials being cut.Table InsertFigure 31. Adjusting table insert height.1. Disconnect the power cord from the outlet.2. Ensure that all four setscrews are firmly incontact with the table casting.3. Using a 6mm hex wrench, raise or lowereach of the four setscrews until the insert isflush with the table top as shown in Figure31.4. Now make sure the blade will not come intocontact with table insert. Position the blade at90°, then raise and lower the blade through itsfull range of motion. Also rotate the bladewhile doing this, making sure that the bladenever contacts any part of the table insert. Dothe same with the blade in the 45° position.Wear leather gloves while rotating the bladeto prevent being cut.5. Be sure to review Section 5: Adjustments,“Blade Parallelism,” before operating thesaw.-26- G1022 Series Contractor Saws

7. Once the fence is adjusted, check the measurementpointer shown in Figure 36 andadjust if necessary.Adjusting BoltCheck NutMeasurement PointerFigure 36B. Adjusting clamp mechanism.Figure 36. Adjust measurement pointer.G1022Z Fence2. Now slide the fence along the rail until it isaligned with the edge of the miter slot. Lockthe fence down.3. Loosen the rear lock adjustment, the slottedscrew on the front of the fence shown inFigure 37, until the rear locking lever ceasesto engage the rear rail with the fence in thelocked position.(The Model G1022ZF, ZFX and PRO use a ShopFox ® fence. Please refer to the instruction manualincluded with the Shop Fox ® fence for completedirections on adjusting the fence.)The fence must engage and square up on thefront rail before the rear clamp engages the backrail. In essence, the rear clamp should act as asecondary mechanism for maintaining fenceposition. When adjusted correctly, the lever lockshould only begin to apply pressure on the backrail over the last one-third of its stroke. To adjustthe fence:1. First, make sure the front clamp is engagingthe front rail with the lock handle at one-halfof its throw. If the front clamp requires adjustment,loosen the check nut shown in Figure36B. Turn the adjusting bolt clockwise if thefront clamp is too far from the rail, counterclockwiseif it is too close.Rear Lock AdjustmentFigure 37. Rear lock adjustment screw.G1022 Series Contractor Saws -29-

Tip – Attach a piece of 3 ⁄4" thick hardwood to theblade side of the fence shown in Figure 39. Thiswill keep thin materials from wedging betweenthe fence and table, and will also protect thefence from coming in contact with the blade whendadoing or ripping thin stock.Front Adjustment ScrewsLocking LeverFigure 38. Adjustment bolts for fence parallelism.4. Loosen the locking lever (Figure 38) until itis approximately two-thirds engaged. Makenote of its position and lift it up all the way.Tighten the rear adjustment screw until therear clamp is approximately 1 ⁄16'' from the rail.Move the lock handle back to its two-thirdsposition. The rear clamp should just betouching the rail. If it is too loose or too tight,lift the handle and turn the adjusting screw insmall increments until the clamp is in itsproper location. NOTE: Do not turn theadjustment screw unless the lock handle isin the up position. Damage to the clampshoe will result if this step is not observed.5. Loosen the locking lever and slide the fencealong the rail. Return the fence to its positionat the edge of the miter slot and slowly applypressure to the lever. If adjustments are correct,the fence should square itself beforethe rear clamp engages. If the rear clampengages before the fence is squared, loosenthe screw one-quarter turn and retest.Figure 39. Attaching a sacrificial fence.6. Once the fence is adjusted, check the measurementpointer shown in Figure 40, andadjust if necessary.Measurement PointerFigure 40. Adjust measurement pointer.-30- G1022 Series Contractor Saws

Blade ParallelismYour table saw will give the best results if themiter slot is parallel to the blade. If they are notexactly parallel, your cuts and finished work willbe lower in quality. To check and adjust bladeparallelism:1. Using an adjustable square, measure thedistance between the miter slot and the frontof your blade as shown in Figures 41 and42.2. Note the first measurement. Rotate theblade 180° and move the square to the rearof the blade. You may find it helpful to markyour blade with a felt-tip pen (as a rotationguide) at the point where the straightedgeand blade meet.3. Compare the measurements. If the differencein measurements is less than 0.004",your blade and table are in acceptable alignmentmove to Step 7. If the difference isgreater, you will need to adjust the trunnionand table.4. To adjust blade alignment, remove themotor, wings and the upper half of the sawfrom the stand. Place it upside down on 4 x4 blocks to allow the saw blade to rotatefreely.5. Remove the handwheels and the sheetmetal body. To maintain the trunnion assemblyas one unit, place a bar clamp across theentire trunnion assembly. The four trunnionbolts (Figure 43) can now be loosened. Thiswill allow the trunnion assembly to be shiftedin order to change the alignment betweenthe blade and the miter slot.Figure 41. 90° blade parallelism measurement.6. Now measure the miter slot to the blade asin Steps 1 and 2. Move the trunnion assemblyuntil proper alignment has beenobtained. Tighten the trunnion bolts andremove the bar clamp.#4 Shim LocationClamp Here#3 Shim LocationTrunnionBoltsTrunnionBoltsFigure 42. 90° blade parallelism measurement.#2 Shim Location#1 Shim LocationClamp HereFigure 43. Table/trunnion assembly.G1022 Series Contractor Saws -31-

7. Now check to see if the blade remains parallelto the miter slot when tilted to 45°.8. Tilt the blade to 45° and repeat Steps 1-5. Ifthe blade is still parallel to the miter slot, continuewith the next section. Otherwise, continuewith the next step.9. If the blade was parallel to the miter slot at90° but not at 45°, the trunnion will need tobe shimmed with metal shim stock. Theshims are placed between the trunnion cornersand the table.#1 Shim #3 Shim#2 Shim#4 ShimFigure 45. 45° blade parallelism measurement.#1 Shim #3 Shim#2 Shim#4 ShimFigure 44A. 45° blade parallelism measurement.10. Refer to Figures 43, 44A, 44B and 45, forshim placement. If the distance of A is shorterthan B, shim(s) will need to be placedunder corners #1 and #2. If the distance of Bis shorter than A, shim(s) will need to beplaced under corners #3 and #4. Very thinshim stock works well, just make sure theyare all the same thickness, and you put anequal number under each of the two corners.11. Tighten down one trunnion bolt a smallamount and then move on to each of the others,tightening each down the same amount.Continue to rotate through the bolts, tighteningthem a little each time until they are allsecure.12. Now recheck the blade to miter slot at 90°and 45° by repeating Steps 1-3 and 8. If thedistance of A and B are equal to or less than0.004" at both 90° and 45°, continue to thenext section. If the distances are still off bymore than 0.004", repeat Steps 4-12.Figure 44B. Shim placement.13. Once you feel you have the miter slot adjustedto the blade, recheck all measurementsand be sure the table mounting bolts aresecure. Repeat Step 10 in “BladeGuard/Splitter” instructions. Also, if you everloosen the trunnion in the future, be sure tomake note of shim placements andreassemble exactly how it came apart.-32- G1022 Series Contractor Saws

45° and 90° StopsBAThe Model G1022 Series is equipped with positivestops at 45° and 90°. When properly adjusted,they provide precise and dependable guidesfor bevel adjustment. To set these stops:1. Unplug the machine! Raise the saw bladeto its maximum height by turning the fronthandwheel clockwise.DC2. Set the saw blade at 90° to the table by turningthe handwheel at the side of the machineas far as it will go. Important: Do not forcethe handwheels when setting the bladeheight or bevel. If the handwheels offer resistance,do not continue turning until youdetermine the source of the resistance.3. Once your blade is set at 90° to the table,place a machinist's square or speed squareagainst the blade and table surface, asshown in Figure 46.Figure 47. 90° and 45° stop bolt adjustments.6. Turn the handwheel until the blade andsquare are flush from top to bottom.7. Snug the adjustment screw and tighten thelock nut. Recheck the blade with the squareto ensure that you have not over tightenedthe screw.8. Using the side handwheel, adjust the bladebevel until you hit the 45° positive stop.Check the bevel with your speed square oran adjustable square set to 45°.9. If variations exist, loosen the lock nut (C) andadjust the stop bolt (D) (Figure 47) until yourblade and square match.10. Tighten the lock nut and recheck the bevelby adjusting the blade back to 90°, then backto 45°. Correct again, if necessary.Figure 46. Checking blade angle to table.4. With the square in place, inspect for variationbetween the blade and square.5. If a gap exists at either the top or the bottomof the square, loosen lock nut (A) and adjustmentbolt (B) indicated in Figure 47.!Disconnect power to themachine when performingany maintenance,assembly or adjustments.Failure to do thismay result in seriouspersonal injury.G1022 Series Contractor Saws -33-

Worm GearMiter GaugeThe degree of resistance at the blade heighthandwheel can be adjusted to compensate forwear or for personal preference. To adjust:1. Loosen the lock nut (A) shown in Figure 48.This will allow the eccentric sleeve that surroundsthe worm gear to turn. Although thisprocess can be done with the handwheel inplace, you may find it easier to remove it first.Initial Step, Model G1022ZF and ZFX:The ZF/ZFX miter gauge has two setscrews inthe miter slot bar which can be set to remove anyfree play from the miter gauge when inserted inthe T-slot. Loosen or tighten the two setscrewsuntil the miter gauge slides freely back and forth,but has no side-to-side movement.Next step for all models:1. Loosen the lock knob on the miter gauge andplace a square against the face of the miterbody and the blade.AB2. Adjust the miter body until there is no spacebetween the square and the blade. Tightenthe lock knob.3. With the stop link in the up position, loosenthe jam nut and adjust the stop screw shownin Figure 49 until it is seated against the stoplink.4. Now loosen the setscrew on the left frontside of the miter bar, adjust the pointer to 90˚and retighten the setscrew.Figure 48. Handwheel resistance adjustment.2. As you watch from below, twist the pointerassembly at the front of the saw. As you turnthe pointer, you’ll see the worm gear movetoward and away from the teeth on the fronttrunnion. Ideally, the worm gear shouldmesh with the teeth without slop or excesstightness. This process requires a bit of trialand error.5. To adjust to 45˚, follow Steps 1-4 using anadjustable square set to 45˚.6. After rotating the miter body from 45˚ to 90˚and back a few times, double check youradjustments at both angles to assure thatyou have accurately set your miter gauge.3. Once you have found a degree of tightnessthat you prefer, tighten the lock nut.4. Loosen the setscrew (B) and pivot the pointerback to zero. Retighten the setscrew.Replace the handwheel.Jam NutStop LinkStop ScrewFigure 49. Miter gauge adjustment points.-34-G1022 Series Contractor Saws

SECTION 6: OPERATIONSPre-Run CheckTest RunBefore you begin to use your Model G1022Series, you should give it a thorough inspection.While making your inspection, ask yourself thefollowing questions:1. Are all the fasteners tight?2. Is the blade mounted correctly?3. Is the saw stable?4. Is it wired properly?5. Is your electrical system properly configured?6. Have you checked your work piece for obviousdefects?7. Are the V-belts properly tensioned and thepulleys properly aligned?8. Is the guard assembly installed and functional?9. Have you checked the saw blade clearancewhen it is adjusted to varying angles anddepths?10. Have you read all warnings and directionsregarding the operation of this machine?!Disconnect power to themachine when performingany maintenance,assembly or adjustments.Failure to do thismay result in seriouspersonal injury.Keep loose clothingrolled up and out of theway of machinery andkeep hair pulled back.Wear safety glasses duringthe entire operationsprocess. Failure to complymay result in seriouspersonal injury.Always wear a dustmask when operatingthe G1022. Using thismachine produces sawdustwhich may causeallergic reactions or respiratoryproblems.1. Face the table saw and stand to the left ofthe blade path.2. With one finger on the START button andone finger on the STOP button, turn the sawon. Be ready to turn it off in case of mishap.3. Watch and listen to the saw. Note whetherthere are any unusual sounds or excessivevibrations.G1022 Series Contractor Saws-35-

4. If anything appears abnormal, immediatelyturn off the saw and fix the problem. If aproblem exists that is beyond the scope ofthis manual, call our service department.5. If the saw is behaving normally, turn it off andprepare to make a cut according to theinstructions outlined in the following sections.2. Cross-cut Blade: Used for cutting acrossthe grain. 10" cross-cut blades havebetween 60-80 teeth (Figure 51), alternatetop bevel or steep alternate top bevel toothprofiles, small hook angle and a shallow gullet.Blade SelectionChoosing the correct blade for the job is essentialfor the safe and efficient use of your table saw.Ignoring this important step could result in damageto the saw and serious injury to the operator.Documented below are the most common sawblades and their uses.1. Rip Blade: Used for cutting with the grain.Typically, 10" rip blades have between 20-40teeth (Figure 50), flat-top ground tooth profileand large gullets to allow for large chipremoval.Figure 51. Crosscutting blade.3. Combination Blade: Used for cutting withand across the grain. A compromisebetween a rip blade and a cross-cut blade, a10" combination blade will typically havebetween 40-50 teeth (Figure 52), an alternatetop bevel and flat or alternate top beveland raker tooth profile. The teeth arearranged in groups of five. The gullets aresmall and shallow within the groups of fiveteeth, similar to a cross-cut blade; then largeand deep between the groups, like a rippingblade.Figure 50. Ripping blade.Figure 52. Combination blade.-36- G1022 Series Contractor Saws

4. Plywood Blade: Used for cutting plywood orveneers. A 10" plywood blade will have 40-80 teeth (Figure 53), a steep alternate topbevel tooth profile and very shallow gullet.Figure 54. Various saw tooth cutting profiles.Figure 53. Plywood blade.5. Thin-kerf: Most types of saw blades areavailable in a thin-kerf style. Used primarilyto minimize stock wastage. It is recommendedthin-kerf blades be used in conjunctionwith a blade stabilizer to reduce blade wobble.Note: Most blade guards/splitters arethicker than most thin-kerf blades. Makesure the stock will pass by the guard/splitterbefore beginning a cut.6. Dado Blades: There are two types of dadoblades: stack and wobble. Stack dadoes areexpensive and time consuming to set up butleave a clean and smooth finish. Stackdadoes are used for fine furniture and cabinetmaking. Wobble dadoes are inexpensiveand easy to set up, but leave a rough finish.7. Moulding Heads: A moulding head is a cutterheadthat attaches to the arbor and holdsindividual moulding knives. We do not recommendtheir use. They are very dangerousand required training beyond the scope ofthis manual.This section on blade selection is by no meanscomprehensive. Always follow the saw blademanufacturer's recommendations to assure safeand efficient operation of your table saw.CrosscuttingCrosscutting means cutting across the grain ofthe wood. In wood products without grain (i.e.MDF, particleboard) it simply means cuttingacross the width of the stock.Crosscuts are made with the miter gauge. Thereare two miter gauge slots in the table top. Use theone that works best for the piece being crosscut.To make a crosscut using the miter gauge:1. Inspect the board for soundness. You do notnecessarily need a square edge to crosscutwith accuracy.2. Inspect the miter gauge. Is it properly set andtight? Move the rip fence completely out ofthe way.3. Turn on the saw and allow it to come to fullspeed.4. Hold the workpiece firmly against the face ofthe miter gauge and ease it into the blade asshown in Figure 55.5. Turn off the saw and allow the blade to cometo a full stop.G1022 Series Contractor Saws -37-

workpiece fully past the blade. When a smallwidth is to be ripped and a push stick cannotbe safely put between the blade and ripfence, rip a larger piece to obtain the desiredpiece.3. Turn on the saw and allow it to reach fullspeed. Place the trued edge of the boardagainst the rip fence. Feed the workpieceslowly and evenly into the blade. Do notstand behind the board as shown in Figure56.Figure 55. Cross-cut operation.RippingRipping means to cut with the grain of the wood.In other materials such as MDF or plywood, rippingsimply means to cut lengthwise. To rip aboard:1. Inspect the board for soundness. You willneed a straight edge to rip with accuracy andsafety. Your workpiece may need to be jointedflat before attempting to cut on the tablesaw.Never attempt to rip a board that does nothave one perfectly straight edge on it.Always run the straight edge of the boardagainst the rip fence. Failure to do thiscould result in kickback and serious personalinjury.Figure 56. Do not stand directly behind wood.Stand out of the line of potential kickback.Hold the workpiece firmly against the fenceand table. Do not allow your fingers to getclose to the blade! Do not reach over theblade to off-load the workpiece.2. Set the rip fence to the desired distance fromthe blade. IF YOU ARE MAKING NARROWCUTS, USE A PUSH STICK. It is unsafe toput your hands close to the blade. A pushstick pattern has been included in this manualon Page 62, or you can purchase theG3445 or G1411 push stick from the Grizzlycatalog. Use them to hold the workpieceagainst the table and fence, and push the-38- G1022 Series Contractor Saws

Dado OperationsIn addition to its ability to rip and crosscut lumber,the table saw is also an invaluable tool for creatinga variety of dadoes. These non-through cutscan be created with a regular saw blade or with aspecially-designed dado blades shown in Figure57.Always use push sticks, featherboards,push paddles and other safety accessorieswhenever possible to increase safety andcontrol during operations which require theblade guard and splitter to be removed fromthe saw. ALWAYS replace the blade guardafter dadoing is complete.Proper dado operations will differ depending onthe blade system you choose. Consult theinstructions included with your dado blades fordirections regarding attachment and adjustment.To use a dado blade:1. Ensure that the saw is switched off and disconnectedfrom its power source.2. Remove the table insert, splitter guard, regularsaw blade.Figure 57. Optional dado blade system.3. Attach and adjust the dado blade system asrecommended in the dado blade’s instructions.4. Install the dado table insert.Never allow hands or arms to be above orbehind the saw blade. Should kickbackoccur, the hands and arms can be pulledinto the saw blade. Serious injury willresult.Never perform a through cut operation witha dado blade. A dado blade was designed tomake non-through cuts only. Failure to followthese directions could result in seriousinjury will result.5. Raise the blade system up to the desireddepth of the dado. Make sure the dado bladewill not cut through the work piece.6. If dadoing along the length of your workpiece,adjust the distance between the fenceand the inside edge of the blade to suit yourneeds. When cutting across the wood grain,use the miter gauge as a guide while dadoing.Remember: Never use the fence as astop in conjunction with your miter gauge.7. Reconnect the saw to the power source.Dado operations present very real hazardsrequiring proper procedures to avoid seriousinjury. The chance of kickback isalways greater when dado blades are usedso extra precautions must be used. Anymovement of the stock away from the fencewill cause kickback. Be certain that stock isflat and straight. Failure to follow thesewarnings could result in serious personalinjury.8. Using a scrap as a test piece, switch on thesaw and take a pass over the dado blade.9. If the cut is satisfactory, repeat with your finishstock.10. Re-install the blade guard.G1022 Series Contractor Saws -39-

Dadoing operations can also be accomplishedusing a conventional saw blade. To create a single-bladedado:1. Clearly mark the width of the dado cut onyour workpiece. Include marks on the edgeof your workpiece so you can clearly identifyyour intended cut while the material is layingflat on the saw table.2. Set the blade height to the depth of cut youwish to create.3. If the dado runs the length of the material,adjust the fence so the blade is aligned withthe inside of your dado channel as shown inFigure 57B.4. Turn on your saw and make the first cut.Rabbet OperationsIn addition to its ability to create a variety ofdadoes, this table saw can be used to cut L-shaped rabbets. These cuts can be created witha regular saw blade or with specially-designedstacking or wobbling dado blades (Figure 57).Proper rabbet operation will differ depending onthe blade system you choose. Consult theinstructions included with your dado blades fordirections regarding attachment and adjustment.To use a dado blade for rabbeting operations:1. Rabbet cutting on the edge of a piece ofstock requires the use of a sacrificial fenceattachment as shown in Figure 58. Thesacrificial fence can be made from a pieceof wood that is as long as the metal fenceand 3 ⁄4" thick. Once the sacrificial fence hasbeen cut, attach it to the metal fence withscrews or clamps, making sure they are allsecure and tight.Rip FenceFigure 57B. Single-blade dado cut.5. Turn off the saw and readjust the fence sothe blade is aligned with the other edge ofthe intended dado channel. Be sure to keepthe cuts within your marks; otherwise, yourdado will be too large.Sacrificial FenceDado InsertBlade Cut-OutFigure 58. Sacrificial fence.6. Turn on the saw and make a second cut.7. Move toward the center of the dado with yoursubsequent cuts until the dado is complete.8. Re-install the blade guard.-40- G1022 Series Contractor Saws

Always use push sticks, featherboards,push paddles and other safety accessorieswhenever possible to increase safety andcontrol during operations which requirethat the blade guard and splitter must beremoved from the saw. ALWAYS replace theblade guard after dadoing is complete.2. Ensure that the saw is switched off and disconnectedfrom its power source.3. Remove the table insert, splitter guard andthe regular saw blade from the arbor.4. Attach and adjust the dado blade system asrecommended in the dado blade instructions.Raise the blade system according twoyour needs. Make sure it will not cut throughthe workpiece.5. If rabbeting along the length of your workpiece,adjust the distance between the fenceand the outside edge of the blade to suit yourneeds as shown in Figure 59. When cuttingacross the wood grain, use the miter gaugeas a guide while rabbeting. Remember:never use the fence as a stop in conjunctionwith your miter gauge.Rabbeting operations can also be accomplishedusing a conventional saw blade. To create a single-bladerabbet:1. Clearly mark the width of the rabbet cut onyour workpiece. Include marks on the edgeof your workpiece so you can clearly identifyyour intended cut while the material is layingflat on the saw table.2. Set the blade height to the depth of cut youwish to create.3. If the rabbet runs the length of the material,adjust the fence so the blade is aligned withthe inside of your rabbet channel.4. Turn on your saw and make the first cut.5. Turn off the saw and readjust the fence sothat the next cut will remove another portionof the wood stock between the inside edge ofthe rabbet and the edge of the wood.6. Turn on the saw and make a second cut.7. Continue to readjust the blade and cut untilthe entire rabbet is made.8. Reinstall the blade guard.6. Using a scrap as a test piece, switch on thesaw and take a pass over the dado blade.7. If the cut is satisfactory, repeat with your finishstock.8. Reinstall the blade guard.Instructions on using moulding heads havebeen intentionally left out. They are verydangerous when not used properly.Considerable skill and training beyond thescope of this manual are required to safelyoperate a moulding head. Serious personalinjury could result if this warning is not followed.Figure 59. Rabbet cutting.G1022 Series Contractor Saws -41-

SECTION 7: MAINTENANCEGeneralLubrication!Disconnect power to themachine when performingany maintenance orrepairs. Failure to do thismay result in seriouspersonal injury.Keep clothing rolledup and out of the wayof machinery and keephair pulled back.The sealed ball bearings in the motor andthroughout the Model G1022 Series require nofurther lubrication during their lifetime. When theydo wear out, replacements can be obtainedthrough the Grizzly Parts Department. Lubricatethe areas indicated below every 12 months.1. Blade angling trunnions. These should belubricated with 6 or 7 drops of light machineoil.2. Blade height trunnion. This should also belubricated with 6 or 7 drops of light machineoil.3. The two (2) worm gears should be lubricatedwith an automotive wheel bearing grease.Wear safety glasses duringthe entire maintenanceprocess. Failureto comply may result inserious personal injury.Regular periodic maintenance on your ModelG1022 Series will ensure its optimum performance.Make a habit of inspecting your machineeach time you use it. Check for the following conditionsand repair or replace when necessary:1. Loose mounting bolts.2. Worn switch.3. Worn or damaged cords and plugs.4. Damaged V-belt.5. Any other condition that could hamper thesafe operation of this machine.TablesTables can be kept rust-free with regular applicationsof products like Boeshield ® T-9. For longterm storage you may want to consider productslike Kleen Bore's Rust Guardit.V-BeltInspect regularly for tension and wear. Check pulleysto ensure that they are properly aligned. Seepulley/V-belt sections for proper tension and pulleyalignment procedures.6. Inspect blades for damage.7. Guard alignment and operation.-42- G1022 Series Contractor Saws

G1022SM AND Z WIRING DIAGRAMG1022 Series Contractor Saws -43-

G1022ZF, ZFX AND PRO WIRING DIAGRAM-44- G1022 Series Contractor Saws

SECTION 8: CLOSUREThe following pages contain general machinedata, parts diagrams/lists, a troubleshooting guideand Warranty/Return information for your ModelG1022 Series.If you need parts or help in assembling yourmachine, or if you need operational information,we encourage you to call our Service Department.Our trained service technicians will be glad to helpyou.If you have comments dealing specifically withthis manual, please write to our Bellingham,Washington location using the address in Section3 Introduction.We have included some important safety measuresthat are essential to this machine’s operation.While most safety measures are generallyuniversal, each workshop is different and safetyrules should be considered as they apply to yourspecific situation.Operating this equipment creates the potentialfor flying debris to cause eye injury.Always wear safety glasses or goggleswhen operating equipment. Everyday glassesor reading glasses only have impactresistant lenses, they are not safety glasses.Be certain the safety glasses you wear meetthe appropriate standards of the AmericanNational Standards Institute (ANSI).We recommend you keep a copy of our currentcatalog for complete information regarding warrantyand return policy. If you need additionaltechnical information relating to this machine, or ifyou need general assistance or replacementparts, please contact the Service Department listedin Section 3 Introduction.Additional information sources are necessary torealize the full potential of this machine. Tradejournals, woodworking magazines, and your locallibrary are good places to start.The Model G1022 Series was specificallydesigned for wood cutting operations. DONOT MODIFY AND/OR USE THIS MACHINEFOR ANY OTHER PURPOSE. Modificationsor improper use of this tool will void thewarranty. If you are confused about anyaspect of this machine, DO NOT use it untilall your questions have been answered orserious personal injury may occur.Like all power tools, there is danger associatedwith the Model G1022 Series.Accidents are frequently caused by lack offamiliarity or failure to pay attention. Usethis tool with respect and caution tolessen the possibility of operator injury. Ifnormal safety precautions are overlookedor ignored, serious personal injury mayoccur.G1022 Series Contractor Saws -45-

MACHINE DATASHEETCustomer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901GRIZZLY MODEL G1022SM 10'' TABLE SAWDesign Type ......................................................................................................Floor ModelOverall Dimensions:Table Height ............................................................................................................37"Table Size ........................................................................................27 1 ⁄8" D x 20 1 ⁄8" WSize With Extension Wings ..............................................................27 1 ⁄8" D x 40 5 ⁄8" WWith Wings and Fence Rails ..................................................................48" W x 44" DMiter Gauge T-Slot ............................................................................................ 3 ⁄8" x 3 ⁄4"Weight (Net) ......................................................................................................240 lbs.Weight (Shipping)..............................................................................................250 lbs.Box # 1 Size..........................................................................37 1 ⁄2" L x 23" W x 18 1 ⁄2" HBox # 2 Size ................................................................................46" L x 3" W x 1 1 ⁄2" HFootprint ........................................................................................................21" x 25"Construction:Table ................................................................................................Ground Cast IronStand ..................................................................................................Pre-formed SteelMiter Gauge ........................................................................................Aluminum ⁄ SteelTrunnions ........................................................................................................Cast IronBearings............................................................Shielded and Lubricated Ball BearingsFence .............................. Single Lever, Front & Rear Locking w/ Micro Adjust KnobRails ..........................................................................44" x 1 3 ⁄8" Chrome Plated TubingGuard ........................................................................................Steel and Clear PlasticWings ............................................................................................Formed Sheet SteelCutting Capacity:Maximum Blade Diameter ........................................................................................10"Maximum Depth of Cut at 90° ................................................................................3 1 ⁄8"Blade Tilt ....................................................................................................0°-45° RightMaximum Depth of Cut at 45° ................................................................................2 1 ⁄8"Maximum Rip to Right of Blade (Standard)..............................................................24"Maximum Rip to Right of Blade (Optional Extension Rails) ....................................48"Maximum Rip to Left of Blade ..................................................................................11"Distance from Front of Table to Center of Blade ....................................................17"Distance from Front of Table to Front of Blade........................................................12"Maximum Width of Dado Cut .................................................................................. 13 ⁄16"Motor:Type ............................................................................TEFC Capacitor Start InductionHorsepower .................................................................................................... 1 1 ⁄2 H.P.Phase / Cycle ..............................................................................Single Phase ⁄ 60 HZVoltage..........................................................................................................110 ⁄ 220VPrewired ................................................................................................................110VAmps ..................................................................................................................16 ⁄ 8AHertz and R.P.M.............................................................................60Hz ⁄ 3450 R.P.M.Power Transfer ..............................................................................................Belt DriveSwitch ..........................................................................................ON/OFF Push ButtonArbor:Dimensions...................................................................................................... 5 ⁄8" x 1 1 ⁄4"Speed ......................................................................................................4,700 R.P.M.Features:........................................Includes Table Inserts for Standard Blade and Dado BladeSpecifications, while deemed accurate, are not guaranteed.-46- G1022 Series Contractor Saws

G1022SM

G1022SM

G1022SM

G1022SM PARTS LISTREF PART # DESCRIPTION REF PART # DESCRIPTION1 P1022001 TABLE INSERT40 P1022040 ECCENTRIC1A P1022001-A DADO INSERT41 P1022041 SHAFT FOR ECCENTRIC2 PSS04M SETSCREW M6-1.0 x 1242 P1022042 SHAFT FOR CLAMP3 P1022Z003A STAND LEG43 P1022043 LOCK LEVER3-1 P1022003-1 FOOT44-1 P1022044-1 PINION W/ KNOB3-2 PB32M HEX BOLT M10-1.5 x 2545 P1022045 CLAMP SHOE3-3 PN02M HEX NUT M10-1.546 P1022046 ADJUSTING BOLT4 P1022004 TABLE47 P1022047 SHAFT BUSHING5 P1022SM005 SHEET METAL WING48 PSS02M SET SCREW M6-1.0 x 66 PW04M FLAT WASHER 10MM49 P1022049 SPRING7 PB01M HEX BOLT M10-1.5 x 3050 P1022050 HAND KNOB8 P1022008 FRONT GUIDE RAIL51 P1022051 SPRING9 P1022009 REAR GUIDE RAIL52 PB03M HEX BOLT M8-1.25 x 1610 P1022010 SPECIAL RAIL BOLT53 PW01M FLAT WASHER 8MM10-1 PW04M FLAT WASHER 10MM54 PN03M HEX NUT M8-1.2510-2 PN02M HEX NUT M10-1.555 PB06M HEX BOLT M8-1.25 x 1211 P1022011 RAIL SPACER56 PW01M FLAT WASHER 8MM12 P1022012 GUIDE RAIL PLUG57 P1022057 BLOCK13 P1022013 CABINET58 P1022058 PIN14 P1022014 GEAR BRACKET59 P1022059 SPRING15 PB03M HEX BOLT M8-1.25 x 1660 P1022060 CLAMP HOOK16 PW01M FLAT WASHER 8MM61 P1022061 LEVER17 PN03M HEX NUT M8-1.2562 P1022062 LOCK LINK18 P1022018 TILTING SCALE63 PS05M PHLP HD SCR M5-0.8 x 819 P1022SM019 LOGO PLATE64 P1022064 FENCE20 PB03M HEX BOLT M8-1.25 x 1673C P1022073C SPLITTER21 PW01M FLAT WASHER 8MM74 PRP20M ROLL PIN 4 x 2222 P1022022 MITER BODY75 P1022075 BRACKET24 PN04M HEX NUT M4-0.777 PB03M HEX BOLT M8-1.25 x 1625 PS01M PHLP HD SCR M4-0.7 x 18 78 PW01M FLAT WASHER 8MM26 P1022026 HAND KNOB79 PB02M HEX BOLT M6-1.0 x 1227 P1022SM027 FIBER WASHER80 PW03M FLAT WASHER 6MM29 P1022029 MITER BAR83 P1022083 HANDLE29-1 P1022029-1 T-SLOT WASHER85 P1022085 KNOB29-2 PFH04M FLAT HD SCR M6-1.0 x 8 87 P1022087 HANDWHEEL30 P1022030 ANGLE POINTER88-1 P1022088-1 POINTER ASSEMBLY31 PSS02M SETSCREW M6-1.0 x 689 PSS03M SETSCREW M6-1.0 x 833 P1022033 STOP LINK90 P1022090 FRONT BRACKET35 PCB01M CARR BOLT M8-1.25x2091 PW01M FLAT WASHER 8MM35-1 PN03M HEX NUT M8-1.2592 PSB13M CAP SCREW M8-1.25x3035-2 PW01M FLAT WASHER 8MM93 P1022093 ANGLE WORM SHAFT37 P1022037 WIDTH POINTER95 P1022095 COLLAR38 P1022038 FENCE ADJUSTER96 PSS02M SETSCREW M6-1.0 x 639 P1022Z039 FRONT CLAMP-50- G1022 Series Contractor Saws

G1022SM PARTS LISTREF PART # DESCRIPTION REF PART # DESCRIPTION97 PRP02M ROLL PIN 3 x 1698 PN05M HEX NUT M16-1.599 P1022090 FRONT TRUNNION100 PRP06M ROLL PIN 5 X 24101 PSS04M SET SCR M6 - 1.0 x 12102 P1022102 WAVY WASHER103 PW03M FLAT WASHER 6MM104 PB08M HEX BOLT M6-1.0 x 20105 PB10M HEX BOLT M6-1.0 x 25106 PN01M HEX NUT M6-1.0107 P1022107 SET PLATE108 P1022108 LINKING BAR109 P1022109 SPACER110 P1022110 ECCENTRIC SLEEVE111 P1022111 WORM SHAFT112 P1022112 SPACER113 P1022113 ARBOR BRACKET114 P1022114 ARBOR BRACKET PIN115 P1022115 ARBOR NUT116 P1022116 FLANGE118 P1022118 BLADE ARBOR120 P6203 BEARING 6203-2RS122 PK01M KEY 5 x 5 x 22MM123 P1022123 WORM124 P1022124 HEX NUT M17125 P1022125 SPINDLE PULLEY125-1 P1022125-1 MOTOR PULLEY126 PSS03M SETSCREW M6-1.0 x 12127 P1022127 REAR TRUNNION128 P1022128 REAR BRACKET129 P1022129 MOTOR BRACKET130 PSS04M SETSCREW M6-1.0 x 12131 P1022131 MOTOR PLATE ROD132 P1022132 MOTOR PLATE133 PB07M HEX BOLT M8-1.25 x 25134 PW01M FLAT WASHER 8MM135 PLW06 LOCK WASHER 5 ⁄8"136 PN03M HEX NUT M8-1.25137 PN05M HEX NUT M16-1.5138 P1022138 SHAFT139 P1022139 BRACKET140 PB26M HEX BOLT M8-1.25 x 30141 PB03M HEX BOLT M8-1.25 x 16142 P1022142 CONNECTING PLATE143 PN03M HEX NUT M8-1.25144 PW01M FLAT WASHER 8MM145 P1022145A SWITCH BRACKET146 P1022146 SWITCH147 PWRCRD110S POWER CORD147-1 PWRCRD110L MOTOR CORD148 P1022148 SPANNER WRENCH149 P1022149 PULLEY GUARD BRACKET150 PB10 HEX BOLT 1 ⁄4"-20 x 2"152 P1022152 SLEEVE153 P1022153 PULLEY COVER154 PWN02 WING NUT 1 ⁄4"-20155 P1022Z155 UPPER BRACKET - LONG155-1 P1022Z155-1 UPPER BRACKET - SHORT155-2 P1022Z155-2 LOWER BRACKET - SHORT155-3 P1022Z155-3 LOWER BRACKET - LONG156 P1022156 WIRE CLAMP157 PS08M PHLP HD SCR M5-0.8 x 12158 PN06M HEX NUT M5-0.8159 PVA43 V-BELT A-43160 G2535 MOTOR 1 1 ⁄2 H.P.161 P1022161 STRAIN RELIEF (Not Shown)162 P1022162 SUPPORTING ARM163 P1022163 RETAINER164 P1022164 PAWL166 P1022Z166 PIN167 P1022167 SPACER171 PB47M HEX BOLT M6-1.0 x 40173 P1022Z173 PIVOT PIN174 P1022Z174 GUARD175 P1022Z175 RETAINER176 P1022068 SPRING179 PLN03M LOCK NUT M6-1.0180 PN02M HEX NUT M10-1.5181 P1022181 SWITCH GUARD182 PS02M PHLP HD SCR M4-0.7 X 12183 PB39M HEX BOLT M6-1.0 x 50250 P1022Z250 CLAMP251 PS05M PHLIP HD SCR M5-0.8 X 8252 P1022Z252 SPRING325 P1022SM325 WARNING LABEL326 P1022SM326 ELECTRICITY LABEL327 P1022SM327 SAFETY GLASSES LABEL328 P1022SM328 MACHINE ID LABEL329 P1022SM329 BLADE GUARD LABELG1022 Series Contractor Saws -51-

MACHINE DATASHEETCustomer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901GRIZZLY MODEL G1022Z TABLE SAWDesign Type ......................................................................................................Floor ModelOverall Dimensions:Table Height ............................................................................................................37"Table Size ........................................................................................27 1 ⁄8" D x 20 1 ⁄8" WTable Size With Extension Wings ....................................................27 1 ⁄8" D x 40 5 ⁄8" WTable With Wings and Fence Rails ........................................................48" W x 44" DMiter Gauge T-Slot ............................................................................................ 3 ⁄8" x 3 ⁄4"Weight (Net) ......................................................................................................240 lbs.Weight (Shipping)..............................................................................................250 lbs.Box # 1 Size ............................................................................36" L x 18 1 ⁄2" W x 25" HBox # 2 Size ..................................................................................46" L x 3" W x 2" HBox # 3 Size ................................................................................12" L x 12" W x 5" HFootprint ........................................................................................................21" x 25"Construction:Table ................................................................................................Ground Cast IronStand ..................................................................................................Pre-formed SteelMiter Gauge ........................................................................................Aluminum ⁄ SteelTrunnions ........................................................................................................Cast IronBearings............................................................Shielded and Lubricated Ball BearingsFence ..............................Single Lever ; Front & Rear Locking w/ Micro Adjust Knob;..............................................................Heavy Extruded Aluminum with Tee Slot TopRails ..........................................................................44" x 1 3 ⁄8" Chrome Plated TubingGuard ........................................................................................Steel and Clear PlasticWings..............................................................Ground Cast Iron, Open Ribbed DesignCutting Capacity:Maximum Blade Diameter ........................................................................................10"Maximum Depth of Cut at 90° ................................................................................3 1 ⁄8"Blade Tilt ....................................................................................................0°-45° RightMaximum Depth of Cut at 45° ................................................................................2 1 ⁄8"Maximum Rip to Right of Blade (Standard)..............................................................24"Maximum Rip to Right of Blade (Optional Extension Rails) ....................................48"Maximum Rip to Left of Blade ..................................................................................11"Distance from Front of Table to Center of Blade ....................................................17"Distance from Front of Table to Front of Blade........................................................12"Maximum Width of Dado Cut .................................................................................. 13 ⁄16"Motor:Type ............................................................................TEFC Capacitor Start InductionHorsepower .................................................................................................... 1 1 ⁄2 H.P.Phase / Cycle ..............................................................................Single Phase ⁄ 60 HZVoltage..........................................................................................................110 ⁄ 220VPrewired ................................................................................................................110VAmps ..................................................................................................................16 ⁄ 8AHertz and R.P.M.............................................................................60Hz ⁄ 3450 R.P.M.Power Transfer ..............................................................................................Belt DriveSwitch ..........................................................................................ON/OFF Push ButtonArbor:Dimension........................................................................................................ 5 ⁄8" x 1 1 ⁄4"Speed ......................................................................................................4,700 R.P.M.Features:........................................Includes Table Inserts for Standard Blade and Dado BladeSpecifications, while deemed accurate, are not guaranteed.-52- G1022 Series Contractor Saws

G1022Z

G1022Z

G1022Z

G1022Z PARTS LISTREF PART # DESCRIPTION1 P1022001 TABLE INSERT1A P1022001-A DADO INSERT2 PSS04M SETSCREW M6-1.0 x 123A P1022Z003A STAND LEG3-1 P1022003-1 FOOT3-2 PB32M HEX BOLT M10-1.5 x 253-3 PN02M HEX NUT M10-1.54 P1022004 TABLE5 G1193 EXTENSION WING6 PW04M FLAT WASHER 10MM7 PB01M HEX BOLT M10-1.5 x 308 P1022Z008 FRONT GUIDE RAIL9 P1022009 REAR GUIDE RAIL10 P1022010 SPECIAL RAIL BOLT10-1 PW04M FLAT WASHER 10MM10-2 PN02M HEX NUT M10-1.511 P1022011 RAIL SPACER12 P1022012 GUIDE RAIL PLUG13 P1022013 CABINET14 P1022014 GEAR BRACKET15 PB03M HEX BOLT M8-1.25 x 1616 PW01M FLAT WASHER 8MM17 PN03M HEX NUT M8-1.2518 P1022018 TILTING SCALE19 P1022SM019 LOGO PLATE20 PB03M HEX BOLT M8-1.25 x 1621 PW01M FLAT WASHER 8MM22 P1022Z022 MITER BODY24 PN04M HEX NUT M4-0.725 PS01M PHLP HD SCR M4 - 0.7 x 1826 P1022026 HAND KNOB27 P1022SM027 FIBER WASHER29 P1022029 MITER BAR29-1 P1022029-1 T-SLOT WASHER29-2 PFH04M FLAT HD SCR M6-1.0 x 830 P1022030 ANGLE POINTER31 PSS02M SETSCREW M6-1.0 x 633 P1022033 STOP LINK35 PCB01M CARR. BOLT M8-1.25 x 2035-1 PN03M HEX NUT M8-1.2535-2 PW01M FLAT WASHER 8MM37 P1022Z037 WIDTH POINTER38 P1022038 FENCE ADJUSTER39 P1022Z039 FRONT CLAMP40 P1022040 ECCENTRICREF PART # DESCRIPTION41 P1022041 SHAFT FOR ECCENTRIC42 P1022042 SHAFT FOR CLAMP43 P1022Z043 LOCK LEVER44-1 P1022044-1 PINION W/ KNOB45 P1022045 CLAMP SHOE46 P1022046 ADJUSTING BOLT47 P1022047 SHAFT BUSHING48 PSS02M SET SCR M6-1.0 x 649 P1022049 SPRING51 P1022051 SPRING52 PB03M HEX BOLT M8-1.25 x 1653 PW01M FLAT WASHER 8MM54 PN03M HEX NUT M8-1.2555 PSB52M CAP SCR M8-1.25 x 1056 PW01M FLAT WASHER 8MM57 P1022057 BLOCK58 P1022058 PIN59 P1022059 SPRING60 P1022060 CLAMP HOOK61 P1022061 LEVER62 P1022062 LOCK LINK63 PS05M PHLP HD SCR M5-0.8 x 864 P1022Z064 FENCE73C P1022073C SPLITTER74 PRP20M ROLL PIN 4 x 2275 P1022075 BRACKET77 PB03M HEX BOLT M8-1.25 x 1678 PW01M FLAT WASHER 8MM79 PB02M HEX BOLT M6-1.0 x 1280 PW03M FLAT WASHER 6MM83 P1022083 HANDLE85 P1022085 KNOB87 P1022087 HANDWHEEL88-1 P1022088-1 POINTER ASSEMBLY89 PSS03M SETSCREW M6-1.0 x 890 P1022090 FRONT BRACKET91 PW01M FLAT WASHER 8MM92 PSB13M CAP SCR M8-1.25 x 3093 P1022093 ANGLE WORM SHAFT95 P1022095 COLLAR96 PSS02M SETSCREW M6-1.0 x 697 PRP02M ROLL PIN 3 x 1698 PN05M HEX NUT M16-1.599 P1022099 FRONT TRUNNION-56- G1022 Series Contractor Saws

G1022Z PARTS LISTREF PART # DESCRIPTION100 PRP06M ROLL PIN 5 X 24101 PSS04M SET SCR M6 - 1.0 x 12102 P1022102 WAVY WASHER103 PW03M FLAT WASHER 6MM104 PB08M HEX BOLT M6-1.0 x 20105 PB10M HEX BOLT M6-1.0 x 25106 PN01M HEX NUT M6-1.0107 P1022107 SET PLATE108 P1022108 LINKING BAR109 P1022109 SPACER110 P1022110 ECCENTRIC SLEEVE111 P1022111 WORM SHAFT112 P1022112 SPACER113 P1022113 ARBOR BRACKET114 P1022114 ARBOR BRACKET PIN115 P1022115 ARBOR NUT116 P1022116 FLANGE118 P1022118 BLADE ARBOR120 P6203 BEARING 6203-2RS122 PK01M KEY 5 x 5 x 22M123 P1022123 WORM124 P1022124 HEX NUT M17125 P1022125 SPINDLE PULLEY125-1 P1022125-1 MOTOR PULLEY126 PSS03M SETSCREW M6-1.0 x 12127 P1022127 REAR TRUNNION128 P1022128 REAR BRACKET129 P1022129 MOTOR BRACKET130 PSS04M SETSCREW M6-1.0 x 12131 P1022131 MOTOR PLATE ROD132 P1022132 MOTOR PLATE133 PB07M HEX BOLT M8-1.25 x 25134 PW01M FLAT WASHER 8MM135 PLW06 LOCK WASHER 5 ⁄8"136 PN03M HEX NUT M8-1.25137 PN05M HEX NUT M16-1.5138 P1022138 SHAFT139 P1022139 BRACKET140 PB26M HEX BOLT M8-1.25 x 30141 PB03M HEX BOLT M8-1.25 x 16142 P1022142 CONNECTING PLATE143 PN03M HEX NUT M8-1.25144 PW01M FLAT WASHER 8MMREF PART # DESCRIPTION145 P1022145A SWITCH BRACKET146 P1022146 SWITCH147 PWRCRD110S POWER CORD147-1 PWRCRD110L MOTOR CORD148 P1022148 SPANNER WRENCH149 P1022149 PULLEY GUARD BRACKET150 PB10 HEX BOLT 1 ⁄4"-20 x 2"152 P1022152 SLEEVE153 P1022153 PULLEY COVER154 PWN02 WING NUT 1 ⁄4"-20155 P1022Z155 UPPER BRACKET - LONG155-1 P1022Z155-1 UPPER BRACKET - SHORT155-2 P1022Z155-2 LOWER BRACKET - SHORT155-3 P1022Z155-3 LOWER BRACKET - LONG156 P1022156 WIRE CLAMP157 PS08M PHLP HD SCR M5-0.8 x 12158 PN06M HEX NUT M5-0.8159 PVA43 V-BELT A-43160 G2535 MOTOR 1 1 ⁄2 H.P.161 P1022Z161 STRAIN RELIEF (Not Shown)162 P1022Z162 SUPPORTING ARM163 P1022Z163 RETAINER164 P1022069 PRAWL166 P1022Z166 PIN167 P1022164 SPACER171 PB47M HEX BOLT M6-1.0 x 40173 P1022Z173 PIVOT PIN174 P1022Z174 GUARD175 P1022Z175 RETAINER176 P1022068 SPRING179 PLN03M LOCK NUT M6-1.0180 PN02M HEX NUT M10-1.5181 P1022Z181 SWITCH GUARD182 PS02M PHLP HD SCR M4-0.7 X 12183 PB39M HEX BOLT M6-1.0 x 50185 PN01M HEX NUT M6-1.0186 G3121 SCALE187 P1022Z187 SPACER188 PFH08M FLAT HD SCR M8-1.25 x 12250 P1022Z250 CLAMP251 PS05M PHLIP HD SCR M5-0.8 X 8252 P1022Z252 SPRING W/ CLIP325 P1022SM325 WARNING LABEL326 P1022SM326 ELECTRICITY LABEL327 P1022SM327 SAFETY GLASSES LABEL328 P1022Z328 MACHINE ID LABEL329 P1022SM329 BLADE GUARD LABELG1022 Series Contractor Saws -57-

MACHINE DATASHEETCustomer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901GRIZZLY MODEL G1022ZF/ZFX/PRO TABLE SAWDesign Type ......................................................................................................Floor ModelOverall Dimensions:Table Height ............................................................................................................37"Table Size ........................................................................................27 1 ⁄8" D x 20 1 ⁄8" WTable Size With Extension Wings ....................................................27 1 ⁄8" D x 40 5 ⁄8" WOverall Dimensions – With Wings and Fence Rails ............................50" D x 52 1 ⁄2" WMiter Gauge T-Slot ............................................................................................ 3 ⁄8" x 3 ⁄4"Blade Tilt ....................................................................................................0°-45° RightWeight (Net) ......................................................................................................325 lbs.Weight (Shipping)..............................................................................................340 lbs.Box # 1 Size (Base)..............................................................37 1 ⁄2" L x 22" W x 22 1 ⁄2" HBox # 2 Size (Fence) ................................................................49" L x 15 1 ⁄2" W x 9" HBox # 3 Size (Accessories) ..........................................................14" L x 14" W x 6" HBox # 4 Size (Motor) ..............................................................10 1 ⁄4" L x 16" W x 9 3 ⁄4" HFootprint ........................................................................................................21" x 25"Construction:Table ................................................................................................Ground Cast IronStand ..................................................................................................Pre-formed SteelMiter Gauge ......................................................Cast Iron ⁄ Steel; Adjusts for Side PlayTrunnions ........................................................................................................Cast IronBearings............................................................Shielded and Lubricated Ball BearingsFence ................................................................................................Shop Fox ® FenceGuard ........................................................................................Steel and Clear PlasticWings..............................................................Ground Cast Iron; Open Ribbed DesignCutting Capacity:Maximum Blade Diameter ........................................................................................10"Maximum Depth of Cut at 90° ................................................................................3 1 ⁄8"Maximum Depth of Cut at 45° ................................................................................2 1 ⁄8"Maximum Rip to Right of Blade (Standard)..............................................................25"Maximum Rip to Right of Blade (Optional Extension Rails) ....................................48"Maximum Rip to Left of Blade ..................................................................................11"Distance from Front of Table to Center of Blade ..................................................17 1 ⁄4"Distance from Front of Table to Front of Blade ....................................................12 1 ⁄2"Maximum Width of Dado Cut .................................................................................. 13 ⁄16"Motor: ZF ZFX PROType...................................................TEFC Capacitor Start Induction............................Horsepower..............................1 1 ⁄2 H.P....................2 H.P....................2 H.P..................Phase / Cycle................................................Single Phase ⁄ 60 HZ.................................Voltage................................................................110 ⁄ 220V...........................................Prewired.....................................110V......................220V.....................220V.................Amps........................................17 ⁄ 8.5A..................26 / 13A..............26 / 13A...............R.P.M....................................................................3450 R.P.M........................................Power Transfer.......................................Power Twist ® Link Belt Drive...........................Switch...........................................................ON/OFF Push Button.................................Arbor:Dimension........................................................................................................ 5 ⁄8" x 1 1 ⁄4"Speed ......................................................................................................4,700 R.P.M.Features:........................................Includes Table Inserts for Standard Blade and Dado Blade......................................U.S.A. Motor, 4" Ported Dust Hood, Link Belt, Rail Mounted SwitchSpecifications, while deemed accurate, are not guaranteed.-58- G1022 Series Contractor Saws

G1022ZF/ZFX/PRO

G1022ZF/ZFX/PRO

G1022ZF/ZFX/PRO

G1022ZF/ZFX/PRO PARTS LISTREF PART # DESCRIPTION1 P1022ZF001 TABLE INSERT1A P1022001-A DADO INSERT2 PSS04M SETSCREW M6-1.0 x 123A P1022Z003A STAND LEG3-1 P1022003-1 FOOT3-2 PB32M HEX BOLT M10-1.5 x 253-3 PN02M HEX NUT M10-1.54 P1022ZF004 TABLE5 G1193 EXTENSION WING6 PW04M FLAT WASHER 10MM7 PB01M HEX BOLT M10-1.5 x 309 P1022ZF009 SPECIAL SCR10 P1022ZF010 SPECIAL SCR11 P1022ZF011 RUBBER GROMMET12 P1022ZF012 SWITCH CORD PLATE13 P1022013 CABINET14 P1022014 GEAR BRACKET15 PB03M HEX BOLT M8-1.25 x 1616 PW01M FLAT WASHER 8MM17 PN03M HEX NUT M8-1.2518 P1022018 TILTING SCALE19 P1022SM019 PLATE LOGO20 PB03M HEX BOLT M8-1.25 x 1621 PW01M FLAT WASHER 8MM22 P1022022 MITER BODY24 PN04M HEX NUT M4-0.725 PS01M PHLP HD SCR M4 - 0.7 x 1826 P1022026 HAND KNOB27 P1022SM027 FIBER WASHER29 P1022ZF029 ADJUSTABLE MITER BAR29-1 P1022029-1 T-SLOT WASHER29-2 PFH04M FLAT HD SCR M6-1.0 x 830 P1022030 ANGLE POINTER31 PSS02M SETSCREW M6-1.0 x 633 P1022033 STOP LINK35 PCB01M CARR. BOLT M8-1.25 x 2035-1 PN03M HEX NUT M8-1.2535-2 PW01M FLAT WASHER 8MM36 PB68 HEX BOLT 10-24 X 3 ⁄8"37 PW03 LOCK WASHER #1038 PN25 HEX NUT 10-2452 PB03M HEX BOLT M8-1.25 x 1653 PW01M FLAT WASHER 8MM54 PN03M HEX NUT M8-1.2573C P1022073C SPLITTER74 PRP20M ROLL PIN 4 x 2275 P1022075 BRACKET77 PB03M HEX BOLT M8-1.25 x 1678 PW01M FLAT WASHER 8MMREF PART # DESCRIPTION79 PB02M HEX BOLT M6-1.0 x 1280 PW03M FLAT WASHER 6MM83 P1022083 HANDLE85 P1022085 KNOB87 P1022087 HANDWHEEL88-1 P1022088-1 POINTER ASSEMBLY89 PSS03M SETSCREW M6-1.0 x 890 P1022090 FRONT BRACKET91 PW01M FLAT WASHER 8MM92 PSB13M CAP SCR M8-1.25 x 3093 P1022093 ANGLE WORM SHAFT95 P1022095 COLLAR96 PSS02M SETSCREW M6-1.0 x 697 PRP02M ROLL PIN 3 x 1698 PN05M HEX NUT M16-1.599 P1022099 FRONT TRUNNION100 PRP06M ROLL PIN 5 X 24101 PSS04M SET SCR M6 - 1.0 x 12102 P1022102 WAVY WASHER103 PW03M FLAT WASHER 6MM104 PB08M HEX BOLT M6-1.0 x 20105 PB10M HEX BOLT M6-1.0 x 25106 PN01M HEX NUT M6-1.0107 P1022107 SET PLATE108 P1022108 LINKING BAR109 P1022109 SPACER110 P1022110 ECCENTRIC SLEEVE111 P1022111 WORM SHAFT112 P1022112 SPACER113 P1022113 ARBOR BRACKET114 P1022114 ARBOR BRACKET PIN115 P1022115 ARBOR NUT116 P1022116 FLANGE118 P1022118 BLADE ARBOR120 P6203 BEARING 6203-2RS122 PK01M KEY 5 x 5 x 22M123 P1022123 WORM124 P1022124 HEX NUT M17125 P1022125 SPINDLE PULLEY125-1 P1022125-1 MOTOR PULLEY126 PSS03M SETSCREW M6-1.0 x 12127 P1022127 REAR TRUNNION128 P1022128 REAR BRACKET129 P1022129 MOTOR BRACKET130 PSS04M SETSCREW M6-1.0 x 12131 P1022131 MOTOR PLATE ROD132 P1022132 MOTOR PLATE133 PB07M HEX BOLT M8-1.25 x 25134 PW01M FLAT WASHER 8MM-62- G1022 Series Contractor Saws

G1022ZF/ZFX/PRO PARTS LISTREF PART # DESCRIPTION135 PLW06 LOCK WASHER 5 ⁄8"136 PN03M HEX NUT M8-1.25137 PN05M HEX NUT M16-1.5138 P1022138 SHAFT139 P1022139 BRACKET140 PB26M HEX BOLT M8-1.25 x 30141 PB03M HEX BOLT M8-1.25 x 16142 P1022142 CONNECTING PLATE143 PN03M HEX NUT M8-1.25144 PW01M FLAT WASHER 8MM145 P1022ZF145 SWITCH L-BRACKET146 P1022ZF146 SWITCH147 PWRCRD110S POWER CORD147-1 PWRCRD110L MOTOR CORD148 P1022148 SPANNER WRENCH149 P1022149 PULLEY GUARD BRACKET150 PB10 HEX BOLT 1 ⁄4"-20 x 2"152 P1022152 SLEEVE153 P1022153 PULLEY COVER154 PWN02 WING NUT 1 ⁄4"-20155 P1022Z155 UPPER BRACKET - LONG155-1 P1022Z155-1 UPPER BRACKET - SHORT155-2 P1022Z155-2 LOWER BRACKET - SHORT155-3 P1022Z155-3 LOWER BRACKET - LONG156 P1022156 WIRE CLAMP157 PS08M PHLP HD SCR M5-0.8 x 12158 PN06M HEX NUT M5-0.8159 P1022ZF159 POWER TWIST BELT160A G5009 1.5 HP USA MOTOR160B G4192 2.0 HP USA MOTOR161 P1022161 STRAIN RELIEF (Not Shown)162 P1022Z162 SUPPORTING ARM163 P1022Z163 RETAINER164 P1022069 PRAWL166 P1022Z166 PIN167 P1022164 SPACER171 PB47M HEX BOLT M6-1.0 x 40173 P1022Z173 PIVOT PIN174 P1022Z174 GUARD175 P1022Z175 RETAINER176 P1022068 SPRING179 PLN03M LOCK NUT M6-1.0180 PN02M HEX NUT M10-1.5182 PS02M PHLP HD SCR M4-0.7 X 12183 PB39M HEX BOLT M6-1.0 x 50189 P1022ZF189 DUST PORT ADAPTER190 P1022ZF190 DUST PORT250 P1022Z250 CLAMP251 PS05M PHLIP HD SCR M5-0.8 X 8REF PART # DESCRIPTION252 P1022Z252 SPRING325 P1022SM325 WARNING LABEL326 P1022SM326 ELECTRICITY LABEL327 P1022SM327 SAFETY GLASSES LABEL328 P1022ZF328 MACHINE ID LABEL G1022ZF328 P1022ZFX328 MACHINE ID LABEL G1022ZFX328 P1022PRO328 MACHINE ID LABEL G1022PRO329 P1022SM329 BLADE GUARD LABELG1022 Series Contractor Saws -63-

TROUBLESHOOTING GUIDESYMPTOMPOSSIBLE CAUSECORRECTIVE ACTIONMotor will not start.Motor will not start; fuses orcircuit breakers blow.Motor overheats.1. Low voltage.2. Open circuit in motor or loose connections.1. Short circuit in line cord or plug.2. Short circuit in motor or loose connections.3. Incorrect fuses or circuit breakers inpower line.1. Motor overloaded.2. Air circulation through the motorrestricted.1. Check power line for proper voltage.2. Inspect all lead connections on motor for loose or open connections.1. Inspect cord or plug for damaged insulation and shorted wires.2. Inspect all connections on motor for loose or shorted terminalsor worn insulation.3. Install correct fuses or circuit breakers.1. Reduce load on motor.2. Clean out motor to provide normal air circulation.Motor stalls (resulting inblown fuses or tripped circuit).1. Short circuit in motor or loose connections.2. Low voltage.3. Incorrect fuses or circuit breakers inpower line.4. Motor overloaded.1. Inspect connections on motor for loose or shorted terminals orworn insulation.2 Correct the low voltage conditions.3. Install correct fuses or circuit breakers.4. Reduce load on motor.Machine slows when operating.Applying too much pressure to workpiece.Feed workpiece slower.Loud, repetitious noise comingfrom machine.1. Pulley setscrews or keys are missingor loose.2. Motor fan is hitting the cover.3. V-belts are defective1. Inspect keys and setscrews. Replace or tighten if necessary.2. Tighten fan or shim cover.3. Replace V-belts. See Maintenance.Blade is not square w/miterslot or fence is not square toblade.1. Blade is warped.2. Table top is not parallel to blade.3. Fence is not parallel to blade.1. Replace blade.2. Make table parallel to blade. See Adjustments.3. Make fence parallel to blade. See Adjustments.Fence hits table top whensliding on to the table.Blade does not reach 90°.1. Front rail is bolted too low on thetable.2. Rear rail is bolted too low on thetable.1. 90° stop bolt is out of adjustment.2. Pointer bracket is hitting before theblade reaches 90°.1. Raise front rail.2. Raise rear rail.1. Adjust 90° stop bolt. See Adjustments.2. File down the right side of the pointer bracket until the bladecan reach 90°.Blade hits insert at 45°.Blade won’t go beneathtable surface.1. Hole in insert is inadequate.2. Table out of alignment.3. Blade position is incorrect.Table top too low.1. File or mill the hole in the insert.2. Align table. See Adjustments.3. Adjust blade position. See Adjustments.Raise table top w/washers.Hand wheels won’t turn.1. Hand wheel key is inserted too far.2. Bullets are wedged.3. Roll pin or setscrew in worm gear iscontacting geared trunnion.1. Remove hand wheel and adjust key.2. Remove hand wheel and adjust bullets.3. Inspect roll pins and setscrews in the worm gear. Tighten ifnecessary.!Disconnect power to themachine when performingany maintenance orrepairs. Failure to do thismay result in seriouspersonal injury.-64- G1022 Series Contractor Saws

CUT HERE TOPUSH 1 ⁄4'' WOODCUT HERE TOPUSH 1 ⁄2'' WOOD1 ⁄2'' GRIDPUSH STICKMAKE FROM 1 ⁄2'' OR 3 ⁄4''WOOD OR THICKNESSLESS THAN WIDTH OFMAT'L TO BE CUTCAUTIONUSE ONLY GOODSTRONG WOOD ORPLYWOODNOTCH TO HELPPREVENT HANDFROM SLIPPINGG1022 Series Contractor Saws -65-

WARRANTY CARDName ____________________________________________________________________________________Street ____________________________________________________________________________________City ______________________________________________________________State________Zip_________Phone Number_______________________E-Mail_______________________FAX________________________MODEL # __________________________Order #______________________________________________The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Ofcourse, all information is strictly confidential.1. How did you learn about us?___Advertisement___Friend___Catalog___Card Deck___World Wide Web___Other__________________________________________________2. Which of the following magazines do you subscribe to.___American Woodworker___Practical Homeowner___Cabinetmaker___Shop Notes___Family Handyman___Today’s Homeowner___Fine Homebuilding___WOOD___Fine Woodworking___Wooden Boat___Home Handyman___Woodshop News___Journal of Light Construction ___Woodsmith___Old House Journal___Woodwork___Popular Mechanics___Woodworker___Popular Science___Woodworker’s Journal___Popular Woodworking___Workbench___Other__________________________________________________3. Which of the following woodworking/remodeling shows do you watch?10. Which benchtop tools do you own? Check all that apply.___1" x 42" Belt Sander___6" - 8" Grinder___5" - 8" Drill Press___Mini Lathe___8" Table Saw___10" - 12" Thickness Planer___8" - 10" Bandsaw___Scroll Saw___Disc/Belt Sander___Spindle/Belt Sander___Mini Jointer___Other__________________________________________________11. How many of the machines checked above are Grizzly? ____________12. Which portable/hand held power tools do you own? Check all that apply.___Belt Sander___Orbital Sander___Biscuit Joiner___Palm Sander___Circular Saw___Portable Planer___Detail Sander___Saber Saw___Drill/Driver___Reciprocating Saw___Miter Saw___Router___Other_____________________________________________________Backyard America___Home Time___The American Woodworker___The New Yankee Workshop___This Old House___Woodwright’s Shop13. What machines/supplies would you like Grizzly Industrial to carry?_____________________________________________________________Other__________________________________________________4. What is your annual household income?___$20,000-$29,999___$60,000-$69,999___$30,000-$39,999___$70,000-$79,999___$40,000-$49,999___$80,000-$89,999___$50,000-$59,999 ___$90,000 +5. What is your age group?___20-29___50-59___30-39___60-69___40-49 ___70 +__________________________________________________________14. What new accessories would you like Grizzly Industrial to carry?____________________________________________________________________________________________________________________15. What other companies do you purchase your tools and supplies from?____________________________________________________________________________________________________________________16. Do you think your purchase represents good value?6. How long have you been a woodworker?___Yes___No___0 - 2 Years___8 - 20 Years___2 - 8 Years___20+ Years7. How would you rank your woodworking skills?___Simple___Advanced___Intermediate___Master Craftsman8. What stationary woodworking tools do you own? Check all that apply.___Air Compressor___Panel Saw___Band Saw___Planer___Drill Press___Power Feeder___Drum Sander___Radial Arm Saw___Dust Collector___Shaper___Horizontal Boring Machine ___Spindle Sander___Jointer___Table Saw___Lathe___Vacuum Veneer Press___Mortiser___Wide Belt Sander___Other__________________________________________________17. Would you recommend Grizzly Industrial to a friend?___Yes___No18. Would you allow us to use your name as a reference for Grizzly customersin your area? Note: We never use names more than three times.___Yes___No19. Comments:_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________9. How many of your woodworking machines are Grizzly? _____________-66- G1022 Series Contractor Saws

WARRANTY AND RETURNSGrizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser fromthe date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warrantyand any and all warranties that may be implied by law, including any merchantability or fitness, for any particularpurpose, are hereby limited to the duration of this written warranty. We do not warrant or representthat the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product andany legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,or consequential damages arising from the use of our products.To take advantage of this warranty, contact us by mail or phone and give us all the details. We will thenissue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton.We will not accept any item back without this number. Proof of purchase must accompany the merchandise.The manufacturers reserve the right to change specifications at any time because they constantly strive toachieve better quality equipment. We make every effort to ensure that our products meet high quality anddurability standards and we hope you never need to use this warranty.Please feel free to write or call us if you have any questions about the machine or the manual.Thank you again for your business and continued support. We hope to serve you again soon.G1022 Series Contractor Saws -67-

FOLD ALONG DOTTED LINEGRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069FOLD ALONG DOTTED LINESend a Grizzly Catalog to a friend:Name_______________________________Street_______________________________City______________State______Zip______TAPE ALONG EDGES--PLEASE DO NOT STAPLE