10 table saw - Grizzly Industrial Inc.

More documents

Recommendations

Info

Worm GearMiter GaugeThe degree of resistance at the blade heighthandwheel can be adjusted to compensate forwear or for personal preference. To adjust:1. Loosen the lock nut (A) shown in Figure 48.This will allow the eccentric sleeve that surroundsthe worm gear to turn. Although thisprocess can be done with the handwheel inplace, you may find it easier to remove it first.Initial Step, Model G1022ZF and ZFX:The ZF/ZFX miter gauge has two setscrews inthe miter slot bar which can be set to remove anyfree play from the miter gauge when inserted inthe T-slot. Loosen or tighten the two setscrewsuntil the miter gauge slides freely back and forth,but has no side-to-side movement.Next step for all models:1. Loosen the lock knob on the miter gauge andplace a square against the face of the miterbody and the blade.AB2. Adjust the miter body until there is no spacebetween the square and the blade. Tightenthe lock knob.3. With the stop link in the up position, loosenthe jam nut and adjust the stop screw shownin Figure 49 until it is seated against the stoplink.4. Now loosen the setscrew on the left frontside of the miter bar, adjust the pointer to 90˚and retighten the setscrew.Figure 48. Handwheel resistance adjustment.2. As you watch from below, twist the pointerassembly at the front of the saw. As you turnthe pointer, you’ll see the worm gear movetoward and away from the teeth on the fronttrunnion. Ideally, the worm gear shouldmesh with the teeth without slop or excesstightness. This process requires a bit of trialand error.5. To adjust to 45˚, follow Steps 1-4 using anadjustable square set to 45˚.6. After rotating the miter body from 45˚ to 90˚and back a few times, double check youradjustments at both angles to assure thatyou have accurately set your miter gauge.3. Once you have found a degree of tightnessthat you prefer, tighten the lock nut.4. Loosen the setscrew (B) and pivot the pointerback to zero. Retighten the setscrew.Replace the handwheel.Jam NutStop LinkStop ScrewFigure 49. Miter gauge adjustment points.-34-G1022 Series Contractor Saws
SECTION 6: OPERATIONSPre-Run CheckTest RunBefore you begin to use your Model G1022Series, you should give it a thorough inspection.While making your inspection, ask yourself thefollowing questions:1. Are all the fasteners tight?2. Is the blade mounted correctly?3. Is the saw stable?4. Is it wired properly?5. Is your electrical system properly configured?6. Have you checked your work piece for obviousdefects?7. Are the V-belts properly tensioned and thepulleys properly aligned?8. Is the guard assembly installed and functional?9. Have you checked the saw blade clearancewhen it is adjusted to varying angles anddepths?10. Have you read all warnings and directionsregarding the operation of this machine?!Disconnect power to themachine when performingany maintenance,assembly or adjustments.Failure to do thismay result in seriouspersonal injury.Keep loose clothingrolled up and out of theway of machinery andkeep hair pulled back.Wear safety glasses duringthe entire operationsprocess. Failure to complymay result in seriouspersonal injury.Always wear a dustmask when operatingthe G1022. Using thismachine produces sawdustwhich may causeallergic reactions or respiratoryproblems.1. Face the table saw and stand to the left ofthe blade path.2. With one finger on the START button andone finger on the STOP button, turn the sawon. Be ready to turn it off in case of mishap.3. Watch and listen to the saw. Note whetherthere are any unusual sounds or excessivevibrations.G1022 Series Contractor Saws-35-
Page 5 and 6: Safety Instructions For Power Tools
Page 7: Statistics prove that most common a
Page 11 and 12: 220V OperationG1022ZFX and G1022PRO
Page 13 and 14: SECTION 3: INTRODUCTIONItem G1022SM
Page 15 and 16: UnpackingPiece InventoryThe Model G
Page 17 and 18: Hardware Recognition ChartUse this
Page 19 and 20: SECTION 4: ASSEMBLYBeginning Assemb
Page 21 and 22: HandwheelsMotorTo mount the handwhe
Page 23 and 24: 7. Place a straightedge across the
Page 25 and 26: BladePlease refer to our current ca
Page 27 and 28: Figure 28. Checking alignment of bl
Page 31 and 32: 7. Once the fence is adjusted, chec
Page 33 and 34: Blade ParallelismYour table saw wil
Page 35: 45° and 90° StopsBAThe Model G102
Page 39 and 40: 4. Plywood Blade: Used for cutting
Page 41 and 42: Dado OperationsIn addition to its a
Page 43 and 44: Always use push sticks, featherboar
Page 45 and 46: G1022SM AND Z WIRING DIAGRAMG1022 S
Page 47 and 48: SECTION 8: CLOSUREThe following pag
Page 49 and 50: G1022SM
Page 51 and 52: G1022SM
Page 53 and 54: G1022SM PARTS LISTREF PART # DESCRI
Page 55 and 56: G1022Z
Page 57 and 58: G1022Z
Page 59 and 60: G1022Z PARTS LISTREF PART # DESCRIP
Page 61 and 62: G1022ZF/ZFX/PRO
Page 63 and 64: G1022ZF/ZFX/PRO
Page 65 and 66: G1022ZF/ZFX/PRO PARTS LISTREF PART
Page 67 and 68: CUT HERE TOPUSH 1 ⁄4'' WOODCUT HE
Page 69 and 70: WARRANTY AND RETURNSGrizzly Industr

10 table saw - Grizzly Industrial Inc.

Create successful ePaper yourself

Delete template?

Save as template?