10 table saw - Grizzly Industrial Inc.

More documents

Recommendations

Info

SECTION 2: CIRCUIT REQUIREMENTS110V OperationThe Model G1022SM, Z and ZF motors areprewired to operate at 110V. See Figure 5 for atypical 110V installation.G1022SM and G1022Z:Under normal 110V use, the Models G1022SMand Z motors draw approximately 16 amps. Werecommend a 20 amp circuit breaker or a 20 ampslow-blow fuse.G1022ZF:Under normal 110V use, the Model G1022ZFmotor draws approximately 17 amps. We recommenda 20 amp circuit breaker or a 20 amp slowblowfuse.Figure 5. Typical 110V 3-prong plug and outlet.The circuit you use should be dedicated, (i.e., themachine should provide the only draw from thatcircuit). If frequent circuit failures occur whenusing this machine, contact our ServiceDepartment or your local electrical contractor.Because of the high amperage draw of the ModelG1022 Series when wired for 110V, standardhousehold circuit wiring may not be of a largeenough gauge. A qualified electrician may need toinstall a new circuit with wires capable of handlinga 20 amperage draw. Do not attempt to modify anexisting circuit by replacing the circuit breakerwith one rated for a higher amperage.-8- G1022 Series Contractor Saws
220V OperationG1022ZFX and G1022PRO:The motors supplied with the Models G1022ZFXand G1022PRO are prewired to operate at 220V.The Models G1022ZFX and G1022PRO are notsupplied with a plug; therefore, a suitable 220Vplug must be wired in. When operating at 220V,we recommend using a NEMA-style 6-15 plugand outlet as shown in Figure 6A. You may also“hard-wire” the machine directly to your panel,provided you place a disconnect switch near themachine. Check the electrical codes in your areafor specifics on wiring requirements.Figure 6A. Typical 220V 3-prong plug and outlet.Under normal use, the motor draws approximately13 amps at 220V. We recommend a 15 amp circuitbreaker for 220V operation. This should besatisfactory for normal use while providingenough protection against circuit damage causedby power surges. Always check to see if your currentwires are capable of handling a 15 amp load.If you are unsure, consult the advice of a qualifiedelectrician. Do not attempt to modify an existingcircuit by replacing the circuit breaker with onerated for a higher amperage.G1022 Series Contractor Saws -9-
Page 5 and 6: Safety Instructions For Power Tools
Page 7: Statistics prove that most common a
Page 13 and 14: SECTION 3: INTRODUCTIONItem G1022SM
Page 15 and 16: UnpackingPiece InventoryThe Model G
Page 17 and 18: Hardware Recognition ChartUse this
Page 19 and 20: SECTION 4: ASSEMBLYBeginning Assemb
Page 21 and 22: HandwheelsMotorTo mount the handwhe
Page 23 and 24: 7. Place a straightedge across the
Page 25 and 26: BladePlease refer to our current ca
Page 27 and 28: Figure 28. Checking alignment of bl
Page 31 and 32: 7. Once the fence is adjusted, chec
Page 33 and 34: Blade ParallelismYour table saw wil
Page 35 and 36: 45° and 90° StopsBAThe Model G102
Page 37 and 38: SECTION 6: OPERATIONSPre-Run CheckT
Page 39 and 40: 4. Plywood Blade: Used for cutting
Page 41 and 42: Dado OperationsIn addition to its a
Page 43 and 44: Always use push sticks, featherboar
Page 45 and 46: G1022SM AND Z WIRING DIAGRAMG1022 S
Page 47 and 48: SECTION 8: CLOSUREThe following pag
Page 49 and 50: G1022SM
Page 51 and 52: G1022SM
Page 53 and 54: G1022SM PARTS LISTREF PART # DESCRI
Page 55 and 56: G1022Z
Page 57 and 58: G1022Z
Page 59 and 60:
G1022Z PARTS LISTREF PART # DESCRIP
Page 61 and 62:
G1022ZF/ZFX/PRO
Page 63 and 64:
G1022ZF/ZFX/PRO
Page 65 and 66:
G1022ZF/ZFX/PRO PARTS LISTREF PART
Page 67 and 68:
CUT HERE TOPUSH 1 ⁄4'' WOODCUT HE
Page 69 and 70:
WARRANTY AND RETURNSGrizzly Industr
show all

10 table saw - Grizzly Industrial Inc.

Create successful ePaper yourself

Delete template?

Save as template?