Digilyzer DL1 User Manual

More documents

Recommendations

Info

Masking events Measurement Functions For a better overview some events can be hidden from the logging display (e.g. the audio signal clips very often or the channel status changes permanently because of time code). Therefore, the Digilyzer offers you the possibility to select which events you want to see or hide. Select the field MASK to enter to the LOGGER DISPLAY MASK screen. Event categories All masking on/off The first column displays all event categories. The complete event category or single events of each category can be masked. The filled square indicates that the event is displayed at the event list. NOTE Masking does not effect the recording. All events are logged at anytime. Overview of used event coding See Appendix. Application hint: Fig 5-23, Logger display mask To read out one specific event only 38 Event visible at event list Event masked (not visible at event list) - select in the LOGGER DISPLAY MASK the ALL ON/OFF field and press enter -> all squares will be empty - select the specific event you are looking for, press enter and the specific square is filled up
vu+ppM The Digilyzer offers a combined VU and PPM meter for two channels (stereo). This combination enables a quick and accurate overview on the momentary peak level and RMS value (power of the signal, which tends to be an indication for the volume). Channel A Channel B Measurement Functions VU meter (thick bar) Fig 5-30, VU+PPM panel Numerical peak hold indicates the all-time max. input peak level of each channel since the VU+PPM mode has been entered. It may be reset by placing the cursor on this value and pressing the return key. Over indicator: Clipping indication; the number of full scale values causing this clipping indication may be adjusted in the SET menu (PPM OVER THRESH). vu+ppM Indication: Digilyzer features • VU, volume units indicated as the thick bar; displays the average volume level of the audio signal. • PPM, peak program meter indicated as the center bar; displays the peak level of the audio signal. 39 PPM meter (thin bar) Numerical peak hold Over indicator Peak hold for PPM
Page 1 and 2: Digilyzer DL1 User Manual
Page 3 and 4: INdex: 1. In t r o d u c t Io n 4 C
Page 5 and 6: egistration Introduction Register a
Page 7 and 8: Warnings In order to avoid any prob
Page 9 and 10: Functions Overview The Digilyzer fe
Page 11 and 12: • Some functions, e.g. SCOPE, are
Page 13 and 14: Connectors The Digilyzer includes t
Page 15 and 16: 3. FIrsT sTeps This chapter is a qu
Page 17 and 18: 8. Change auto power off time - Mov
Page 19 and 20: Menu Bar The menu bar allows the us
Page 21 and 22: setup screen Basic Operation The se
Page 23 and 24: display Basics Debugging and analyz
Page 25 and 26: Following errors are analyzed/visua
Page 27 and 28: 5. MeAsureMeNT FuNCTIoNs Channel St
Page 29 and 30: Row number Measurement Functions Pa
Page 31 and 32: Consistency Check The consistency c
Page 33 and 34: Bit statistic The bit statistic fun
Page 35 and 36: Logger The event logger records any
Page 37: Displaying events The display of th
Page 41 and 42: Level Measurement The Level menu fe
Page 43 and 44: Level RMS The analog Level RMS func
Page 45 and 46: Level Sweep The Digilyzer supports
Page 47 and 48: THd+N The THD+N function (Total Har
Page 49 and 50: scope The scope shows the waveform
Page 51 and 52: 7. ACCessorIes MiniLINK MiniLINK al
Page 53 and 54: 8. AppeNdIx 1C2f Format The AES3 st
Page 55 and 56: Logger Event Coding The following c
Page 57 and 58: DL1 event Cs WordLeN Cs CHACHB Cs o
Page 59 and 60: Byte Bit Bit-info Digilyzer Explana
Page 61 and 62: Appendix Consumer Format Coding Ove
Page 63 and 64: Appendix Byte Bit Bit-info Digilyze
Page 65 and 66: Dimensions (L x W x H) 163 x 86 x 4

Digilyzer DL1 User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?