Digilyzer DL1 User Manual

More documents

Recommendations

Info

DL1 event Fr pArITY Fr BLoCKCrCC Au overLoAd Au MuTe Au WordLeN Cs CoN/pro Cs eMpHAsIs Cs FreQueNCY Appendix description Parity error. The parity of the received signals is not correct (problems on the transmission line). CRCC Error. The CRCC of the channel status information is incorrect (problems on the transmission line). Audio signal based events A clipping in the audio signal is detected. The clipping detector is configured in the Digilyzer setup screen. The setting for “PPM OVER THRESH” is stored within the log. No audio signal but only zeros have been found. The measured word length or the audio signal has changed (do not confuse with the word length signalized in the channels status). Channel status based events The professional / consumer indication bit in the channel status has changed. The emphasis bit of the channel status has changed. The signalized sample frequency in the channel status has changed. 56 remark n.a. ADAT 10 rec./s n.a. ADAT 10 rec./s sample 10 rec./s 10 rec./s n.a. ADAT, 10 rec./s n.a. ADAT, 10 rec./s n.a. ADAT, 10 rec./s
DL1 event Cs WordLeN Cs CHACHB Cs oTHer IC FreQueNCY IC WordLeN IC FreQppM IC Mode1C2f Appendix description The signalized word length in the channel status has changed. The status of channel A is not equal to the channel status of channel B. Other bits than those mentioned in this table changed in the channel status. Consistency check based events The sampling frequency indicated in the channel status is not equal to the measured sampling frequency. The world length indicated in the channel status is not equal to the measured word length. The measured accuracy of the sampling frequency is worse than the accuracy indicated in the channel status (consumer mode only). In the professional format the 1C2f mode should be signalized when used. This event occurs if the pro channel status signalizes a 1C2f mode but the Digilyzer is not set to 1C2f mode or vice versa. 57 remark n.a. ADAT, 10 rec./s n.a. ADAT, 10 rec./s n.a. ADAT, 10 rec./s n.a. ADAT, 1 rec./s n.a. ADAT, 1 rec./s n.a. ADAT, 1 rec./s n.a. ADAT, 1 rec./s
Page 1 and 2:
Digilyzer DL1 User Manual
Page 3 and 4:
INdex: 1. In t r o d u c t Io n 4 C
Page 5 and 6: egistration Introduction Register a
Page 7 and 8: Warnings In order to avoid any prob
Page 9 and 10: Functions Overview The Digilyzer fe
Page 11 and 12: • Some functions, e.g. SCOPE, are
Page 13 and 14: Connectors The Digilyzer includes t
Page 15 and 16: 3. FIrsT sTeps This chapter is a qu
Page 17 and 18: 8. Change auto power off time - Mov
Page 19 and 20: Menu Bar The menu bar allows the us
Page 21 and 22: setup screen Basic Operation The se
Page 23 and 24: display Basics Debugging and analyz
Page 25 and 26: Following errors are analyzed/visua
Page 27 and 28: 5. MeAsureMeNT FuNCTIoNs Channel St
Page 29 and 30: Row number Measurement Functions Pa
Page 31 and 32: Consistency Check The consistency c
Page 33 and 34: Bit statistic The bit statistic fun
Page 35 and 36: Logger The event logger records any
Page 37 and 38: Displaying events The display of th
Page 39 and 40: vu+ppM The Digilyzer offers a combi
Page 41 and 42: Level Measurement The Level menu fe
Page 43 and 44: Level RMS The analog Level RMS func
Page 45 and 46: Level Sweep The Digilyzer supports
Page 47 and 48: THd+N The THD+N function (Total Har
Page 49 and 50: scope The scope shows the waveform
Page 51 and 52: 7. ACCessorIes MiniLINK MiniLINK al
Page 53 and 54: 8. AppeNdIx 1C2f Format The AES3 st
Page 55: Logger Event Coding The following c
Page 59 and 60: Byte Bit Bit-info Digilyzer Explana
Page 61 and 62: Appendix Consumer Format Coding Ove
Page 63 and 64: Appendix Byte Bit Bit-info Digilyze
Page 65 and 66: Dimensions (L x W x H) 163 x 86 x 4
show all

Digilyzer DL1 User Manual

Create successful ePaper yourself

Delete template?

Save as template?