Digilyzer DL1 User Manual

More documents

Recommendations

Info

6. TrouBLesHooTING In case the Digilyzer is malfunctioning the software may be reset to factory set up as described below. System Break Down • Switch off the device. • Reset the Digilyzer to the default status by pressing the ESC button and switching on the Digilyzer simultaneously. • Release the ESC button. • The below screenshot will appear on the display stating on the bottom line LOADING DEFAULT SETUP. • Verify the correct operation. Serial number In case you find system breakdowns happening several times or your device is malfunctioning, please note serial number and software release number and contact the local NTi Audio representative in your country. For contact details see the NTi Audio web page: www.nti-audio. com Monitoring Troubleshooting Fig 6-01, Start up screen loading default setup In two channel measurement functions (e.g. Level peak) the monitoring signal of channel A and B are mixed together (stereo). In case one of the channels is muted the stereo monitoring signal has a reduced level. 50 Software release number
7. ACCessorIes MiniLINK MiniLINK allows documentation and data acquisition of all DL1 functions in conjunction with the easy to use MiniLINK PC software. MiniLINK is an upgradeable kit for all existing and new Minilyzers. It consists of a small plug-in USB interface board that can be easily installed without any tools. MiniLINK allows • Storing measurement results and screenshots into the DL1 flash memory • Logging on-line measurement results onto the PC Mains power Adapter Accessories The Digilyzer can be powered by batteries or by an external power. This power adapter is ideally suited for external power supply. Applicable for european connector types only. Cable length = 2 meter. Fig 7-02, Mains power adapter 51 Fig 7-01, MiniLINK
Page 1 and 2: Digilyzer DL1 User Manual
Page 3 and 4: INdex: 1. In t r o d u c t Io n 4 C
Page 5 and 6: egistration Introduction Register a
Page 7 and 8: Warnings In order to avoid any prob
Page 9 and 10: Functions Overview The Digilyzer fe
Page 11 and 12: • Some functions, e.g. SCOPE, are
Page 13 and 14: Connectors The Digilyzer includes t
Page 15 and 16: 3. FIrsT sTeps This chapter is a qu
Page 17 and 18: 8. Change auto power off time - Mov
Page 19 and 20: Menu Bar The menu bar allows the us
Page 21 and 22: setup screen Basic Operation The se
Page 23 and 24: display Basics Debugging and analyz
Page 25 and 26: Following errors are analyzed/visua
Page 27 and 28: 5. MeAsureMeNT FuNCTIoNs Channel St
Page 29 and 30: Row number Measurement Functions Pa
Page 31 and 32: Consistency Check The consistency c
Page 33 and 34: Bit statistic The bit statistic fun
Page 35 and 36: Logger The event logger records any
Page 37 and 38: Displaying events The display of th
Page 39 and 40: vu+ppM The Digilyzer offers a combi
Page 41 and 42: Level Measurement The Level menu fe
Page 43 and 44: Level RMS The analog Level RMS func
Page 45 and 46: Level Sweep The Digilyzer supports
Page 47 and 48: THd+N The THD+N function (Total Har
Page 49: scope The scope shows the waveform
Page 53 and 54: 8. AppeNdIx 1C2f Format The AES3 st
Page 55 and 56: Logger Event Coding The following c
Page 57 and 58: DL1 event Cs WordLeN Cs CHACHB Cs o
Page 59 and 60: Byte Bit Bit-info Digilyzer Explana
Page 61 and 62: Appendix Consumer Format Coding Ove
Page 63 and 64: Appendix Byte Bit Bit-info Digilyze
Page 65 and 66: Dimensions (L x W x H) 163 x 86 x 4

Digilyzer DL1 User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?