Cartridge and block spindles - Gilman USA

More documents

Recommendations

Info

Gilman6500CMotorized verticaltravel spindles6500C motorized vertical travel spindle units are fixed-speed units that combinea motorized timing belt drive spindle with a vertical hardened steel way slide assembly.Vertical positioning of the saddle and spindle can be accomplished with oneof the eight standard drive types.The lead screw manual drive is a 2:1 reduction right angle drive and can bepositioned six ways with position #1 as standard (specify position number whenordering). For 6500C spindle capabilities, reference the 6500 specification charts.*Handwheel pos. #1 STD.Pos. #2,3,4,5,& 6 optional3/8-16 Tap .75 DP. (4)4.625 B.C.8.00 7.00 8.505/16 Sq. key3/4 Soc. HD. C.S. (4)8.00 7.00 8.50#2#3Ø12.91 (256T)Ø14.50 (284T)21.00 (256T)22.09 (284T)5.252.88 10.385.25 Ø5.375Ø1.375Pos. #12.252.753.7512" Dia. handwheel.0005 Graduated dial3.0012.38#6 #5#48.817.1223.0017.00 Max.15.00 Min.*28.0048.00558.00“Y”14.811.8813.25 3.2527.003.001.000Typ.9.5019.00.39 Typ.D1, M1 - Lead screw power drive2.000-.500 Rolled ball screw R.H. Thd.D2, M2 - Lead screw power drive2.000-.500 Ground ball screw R.H. Thd.D3, M3 - Lead screw power drive50mm-10mm Ground ball screw R.H. Thd.Note: * See 6500C cartridge spindles on page 34.**M1, M2, M3 - Motor mount for customer suppliedmotor. Consult factory for specifications.E1 - Lead screw power drive2.500-.250 Acme screw L.H. Thd.Drive “Y” Min. “Y” Max.D1, M1 9.00 22.00D2, M2 9.00 23.00D3, M3 9.00 23.00E1 9.00 25.00H2 9.00 25.0038 ©2011 Gilman USA, LLC
6500C Vertical travelSpindle R.P.M.MotorMinimum Maximum R.P.M. H.P. Frame550 1750 1160 10 or 256T15 284T850 2650 1750 15 or 254T20 256TGilman6500CMotorized verticaltravel spindles1750 4300 3500 15 or 254T20 256TLube points (4)21 in./lube pointLube points (4)40 in./lube point1/2-14 Pipe tapports (2)Medium pressure hydraulic cylinder4" bore 16" strokeCushioned both endsMaximum line pressure 750 P.S.I.Adjustablestops (2)23.38*“Y”H2- Hydraulic cylinder drive4.00" bore cylinderApprox. wt. 2,600 lbs.Note: * See 6500C cartridge spindles on page 34.©2011 Gilman USA, LLC39
Page 1: Cartridge andblock spindlesA wide s
Page 6: OrderinginstructionsEach spindle as
Page 10 and 11: Gilman2750CCartridge spindles2750C
Page 12 and 13: Gilman2750CMotorized spindles2750C
Page 14: Gilman2750CMotorized verticaltravel
Page 20 and 21: Gilman3500CMotorized verticaltravel
Page 22 and 23: Gilman4000CCartridge spindles.88.50
Page 28 and 29: Gilman5500CCartridge spindles.88.50
Page 34 and 35: Gilman6500CCartridge spindles1.12.6
Page 40 and 41: Gilman8000CCartridge spindles1.1227
Page 44 and 45: Gilman specialspindle modulesSpecia
Page 46 and 47: Gilmanspindleaccessories.88.281 Coo
Page 48 and 49: GilmanspindleaccessoriesThe Gilman
Page 50 and 51: ApplicationexamplesThe following ap
Page 52 and 53: Special fast track design,close tol
Page 54 and 55: Heat transfercore manufacturingmach
Page 56 and 57: Speedy domestic spindleservice save
Page 58 and 59: Single, 25 hp, CAT 50 integrallymot
Page 60 and 61: Rigidity of verticaltravel improved
Page 62 and 63: Motorized spindlesfinish wrist-pin
Page 64 and 65: Upstream design andcontinuous opera
Page 66 and 67: Scanning the horizon for enhanced s
Page 68: Gilman USA, LLC1230 Cheyenne Avenue

Cartridge and block spindles - Gilman USA

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?