<strong>Gilman</strong>8000C<strong>Cartridge</strong> <strong>spindles</strong>1.1227.445.00 18.75 3.693.005.50.622.822.291.50.505/8 Soc. HD. C.S. (4)Ø9.25 B.C.1.0008000C cartridge <strong>spindles</strong> <strong>and</strong>8000B <strong>block</strong> <strong>spindles</strong> are availablewith three st<strong>and</strong>ard nose types<strong>and</strong> six st<strong>and</strong>ard internal constructiontypes.Nose types:• #50 N.M.T.B. taper• Boring nose• HSKC100 manual clampInternal constructions:• X1 duplex ball bearing at noseend with contact seal• X2 duplex ball bearing at noseend with labyrinth seal• X2C duplex ceramic ball bearingat nose end with labyrinth seal•X3 triplex ball bearing at noseend with contact seal•X4 triplex ball bearing at noseend with labyrinth seal•X4C triplex ceramic ball bearingat nose end with labyrinth sealRefer to the 8000C/8000Bspecification chart, as well as thesizing instructions on page 5, toselect the proper spindle for yourrotational requirements. Specialdesigns are also available to meetyour specific needs.Ø8.000Ø1.250Ø2.5005/8 Sq. key5.001.13 3.00Ø8.000Ø2.5005/8 Sq. key5.001.13 3.00Ø1.06Ø.5328.1818.75Ø1.562.291.50**4.431.69Ø5.50 Ø10.50Ø5.062 Ø7.25Ø5.51 Ø10.50Ø3.467 Ø7.25Ø7.25Ø8.000 Ø5.91 Ø10.50Ø2.5005/8 Sq. key50 - #50 N.M.T.B. Taper shaftBN - Boring noseØ.5329.2818.752.291.50HM - HSKC100 Manual clamp(T-wrench not included)*5.535/8-11 Tap (4)Ø4.000 B.C.5/8 Soc. HD. C.S. (4)Ø9.25 B.C.M10X1.5 Tap (6)Ø4.685 B.C.5/8 Soc. HD. C.S. (4)Ø9.25 B.C.8000C & 8000B Specification chart8000C Approx. wt. 260 lbs.For cartridge spindlebrackets, see “<strong>Gilman</strong> spindleaccessories”, page 47.Bearing Maximum Maximum Radial stiffness Nose end Drive end<strong>and</strong> seal thrust R.P.M. at noseconstruction (lbs.) (lbs./in.) Bearing Seal Bearing SealnumberX1L 370 1,800 1,430,000 100 mm I.D. 85 mm I.D.X1M 950 1,800 1,630,000 duplex Contact duplex LabyrinthX1H 2,045 1,800 1,780,000 ball ballX2L 370 5,700 1,430,000 100 mm I.D. 85 mm I.D.X2M 950 4,600 1,630,000 duplex Labyrinth duplex LabyrinthX2H 2,045 3,100 1,780,000 ball ballX2CL 215 8,000 1,430,000 100 mm I.D. 85 mm I.D.X2CM 448 7,000 1,630,000 duplex Labyrinth duplex LabyrinthceramicceramicballballContinued on next page40 ©2011 <strong>Gilman</strong> <strong>USA</strong>, LLC
<strong>Gilman</strong>8000BBlock <strong>spindles</strong>5.001.12 3.00.5027.44.5020.25 2.195.501.32.79Ø1.06 Ø1.565/8-11 Tap (4)Ø4.000 B.C.1.000Ø1.250Ø2.5005/8 Sq. keyØ5.50Ø7.25Ø5.0621.005.3759.38(4) Tapped holes.See page 47for location2.255/8 Soc. HD. C.S. (6).500 .392.9381.0009.37510.50018.06318.7550 - #50 N.M.T.B. Taper shaft*4.000 4.0004.7509.50.25Locating edge5.001.13 3.00Ø.5328.1820.25.792.931.69M10X1.5 Tap (6)Ø4.685 B.C.Ø2.500Ø5.51Ø3.467 Ø7.255/8 Sq. keyBN - Boring nose*5.001.13 3.0029.2820.254.03.79Ø2.500Ø5.91Ø7.255/8 Sq. keyHM - HSKC100 Manual clamp(T-wrench not included)*8000C & 8000B Specification chart (continued)Bearing Maximum Maximum Radial stiffness Nose end Drive end<strong>and</strong> seal thrust R.P.M. at noseconstruction (lbs.) (lbs./in.) Bearing Seal Bearing SealnumberX3L 750 1,800 2,150,000 100 mm I.D. 85 mm I.D.X3M 2100 1,800 2,450,000 triplex Contact duplex LabyrinthX3H 4700 1,800 2,630,000 ball ballX4L 750 4,600 2,150,000 100 mm I.D. 85 mm I.D.X4M 2100 3,100 2,450,000 triplex Labyrinth duplex LabyrinthX4H 4700 1,800 2,630,000 ball ball* Maximum tool overhang(from *) = 9 3/8 (in.)Maximum torque = 7460 (in.- lbs.)WK 2 = 210.1 (lb.- in. 2 )Note: Spindles are supplied with medium bearingpreloads as st<strong>and</strong>ard. Light <strong>and</strong> heavy bearingpreloads are available.Tool overhang pertains to boring, end milling <strong>and</strong>nonsupported arbor milling.X4CL 425 7,000 2,150,000 100 mm I.D. 85 mm I.D.X4CM 884 5,500 2,450,000 triplex Labyrinth duplex Labyrinthceramicceramicballball©2011 <strong>Gilman</strong> <strong>USA</strong>, LLC41