MAG-Manual - Refurbished Vending Machines

More documents

Recommendations

Info

SECTION 4: MAINTENANCERemoving the Lower Sensor Board(see Figure 18)Remove the Phillips screw that secures the sensor boardto the lower housing, unsnap the lower housing antipullbacksensor board and remove the lower sensorboardFigure 18LOWER HOUSINGANTI-PULLBACKSENSOR BOARDLOWER SENSORBOARDSPRINGRemoving the Mag Roller and Spring(see Figure 18)Remove the two Phillips screws that secure the rollerspring and remove the springRemoving the Lower HousingAnti-Pullback Lever and Spring(see Figure 19)Using a small drift or Phillips screwdriver, depress thelocking tab in the small hole in top of the lower housingAt the same time, insert a small standard blade screwdriverinto the center slot and push the anti-pullbackassembly back out of the retaining tabs Remove the antipullbacklever from its mount by releasing the lockingtabs Pay close attention to the placement of the spring toassure its correct position on reassemblyFigure 19ANTI-PULLBACKMOUNTANTI-PULLBACKLEVERSPRING18
SECTION 4: MAINTENANCERemoving the Lower Housing Rollers andPulleys (see Figure 20)Slide the front pulleys off the shaftTo remove the center belt, slide the back pulleys off theshaft Gently tap the back shaft with a small hammeruntil the shaft splines are free from the center pulleyFigure 20MAG50 CLEANING MAINTENANCEPROCEDURENOTE: Petroleum-based cleaners and freon-basedpropellants can damage plastic and some electroniccomponents Scouring pads and stiff brushes may harmthe protective coating on the circuit boards and can marthe plastic These items should never be used whencleaning the MAG bill acceptorThe MAG50 should be cleaned every 20,000 bills orevery two years (or as needed, depending on the environmentalconditions of the location) Dust can be removedwith a soft brush or cloth or it can be blown out usingcompressed airFRONT PULLEYBACK PULLEYSHAFTProcedure1 Disconnect power from the bill acceptor2 Remove the bill box and use a soft cloth to wipe anydust from around the intermediate frame and stackerplate3 Remove the lower housing4 Using compressed air or a soft brush, blow or brushthe dust off of the optic sensors5 Remove dust from around the rollers on the lowerhousing and the sensors on the upper sensor boardThe upper sensors are located directly above thelower housing sensors when the lower housing isinstalled6 The bill path can be further cleaned of any dirt or oilby using a soft cloth moistened with a mild soap andwater solution7 Clean the magnetic head with a cotton swab andisopropyl alcohol8 Remove dust from the transport belt areas and anyother places of build up9 Once the lower housing is dry, place it back into themainframe making sure the tab on the bottom locksinto place10 Remount the bill box11 Apply power and insert bills to verify the unit isfunctioning properly19
Page 3 and 4: TABLE OF CONTENTSSection 1: General
Page 5 and 6: SECTION 1: GENERAL INFORMATIONMAIN
Page 7: SECTION 2: INSTALLATIONOPTION SWITC
Page 10 and 11: SECTION 3: OPERATIONINTERCONNECTION
Page 12 and 13: SECTION 4: MAINTENANCEDISASSEMBLING
Page 14 and 15: SECTION 4: MAINTENANCERemoving the
Page 16 and 17: SECTION 4: MAINTENANCERemoving the
Page 20 and 21: SECTION 4: MAINTENANCEMAG50 CLEANIN
Page 22 and 23: SECTION 5: TROUBLESHOOTINGThree Bli
Page 24 and 25: SECTION 5: TROUBLESHOOTINGElevenBli
Page 26 and 27: SECTION 5: TROUBLESHOOTINGEighteenB
Page 28 and 29: SECTION 6: PARTS LISTMAIN FRAMEMAG5
Page 30 and 31: SECTION 6: PARTS LISTMAG50B/MAG52BX
Page 32 and 33: LOGIC BOARD AND CASE ASSEMBLYSECTIO
Page 34 and 35: SECTION 6: PARTS LISTHARNESSES123IT
Page 36: COIN ACCEPTORS, INC300 Hunter Avenu

MAG-Manual - Refurbished Vending Machines

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?