PNEG-1162CEX - DMC DIII Stir-Ator - David Manufacturing Co.

More documents

Recommendations

Info

5. InstallationMinimum Cable RequirementsMain CurrentProtectionSupply toSlip Ring *Slip Ring toBeam BoxBeam Box toAuger MotorBeam Box toTrack MotorTwin Auger,3 PhaseFuse3 x 25A6 mm²6 Core H074 mm²5 Core H071.5 mm²4 Core H071.5 mm²3 Core H07Triple Auger,3 PhaseFuse 3 x 33 x 32A6 mm²6 Core H076 mm²5 Core H071.5 mm²4 Core H071.5 mm²3 Core H07Twin Auger,1 PhaseFuse2 x 25A6 mm²6 Core H076 mm²5 Core H072.5 mm²3 Core H071.5 mm²3 Core H07Triple Auger,1 PhaseMotor ProtectionUnit 32A6 mm²6 Core H076 mm²5 Core H072.5 mm²3 Core H071.5 mm²3 Core H07* Note, sixth core carries 230 VAC signal for ‘Stir Guard’.1. Run a five (5) core cable, as shown in Figure 5AF below, Figure 5AG on Page 23 and Figure 5AHon Page 23, from the slip ring junction box to the beam box, running through the openings given andover the cable arms.2. BEFORE CUTTING TO LENGTH, CHECK THERE IS SUFFICIENT LENGTH TO PREVENTDAMAGE AS THE TROLLER MOVES UP AND DOWN THE BEAM.3. CHECK THAT THE LOOP OF CABLE DOES NOT FOUL ON ANY PARTS OF THE STIRRER.5 Core H07 cableFigure 5AF Cable Route in Centre Yoke22 PNEG-1162CEX DMC DIII Stir-Ator
5. Installation5 Core H07 cableFigure 5AG Cable Route Out of TubeCable gland5 Core H07 cableBeam box4. Use wire ties to tie the cable to the cable arms.Figure 5AH Cable Route into Beam Box5. Run a cable from the beam box to the auger motors as shown in Figure 5AG.3 or 4 CoreH07 cableAuger motorcable glandFigure 5AI Cable Route to Auger MotorPNEG-1162CEX DMC DIII Stir-Ator 23
Page 1 and 2: DMC DIII Stir-AtorOwner’s ManualP
Page 3 and 4: Table of ContentsContentsChapter 1
Page 5 and 6: Installation1. The correct installa
Page 7 and 8: 3. Bin LoadingUser’s must be awar
Page 9 and 10: 5. InstallationGSI RECOMMENDS THAT
Page 11 and 12: 5. InstallationFigure 5E Suspension
Page 13 and 14: 5. Installation4. NOTE: Augers used
Page 15 and 16: 5. Installation10 mmFigure 5O Corre
Page 17 and 18: 5. Installation12. NOTE: 36' and la
Page 19 and 20: 5. Installation15. Attach the slip
Page 21: 5. InstallationCable glandsBeam box
Page 25 and 26: 5. InstallationNOTE: Installer must
Page 27 and 28: 5. InstallationCentre Suspension As
Page 29 and 30: 5. InstallationFigure 5AV Lock Unit
Page 31 and 32: 5. Installation6. Use a small grind
Page 33 and 34: 5. Installation9. Re-check and adju
Page 35 and 36: 7. WarrantyGSI Group, LLC Limited W

PNEG-1162CEX - DMC DIII Stir-Ator - David Manufacturing Co.

Create successful ePaper yourself

Delete template?

Save as template?