Installation Manual - Unical Lattner Condensing Hot Water Boilers

More documents

Recommendations

Info

Instructions for the installer3.2 - CODE AND STANDARDSAPPROVALSALKON 90 has been reviewed for compliance with theapplicable sections of the following NorthAmerican Standards:ANSI Z21.13/CSA 4.9 - Gas-fired low pressuresteam and hot water boilersASME SECTION IV: ASME Boiler and Pressure VesselCode with addenda, Section IV: Rules for Construction ofHeating <strong>Boilers</strong>BTS - 2000 TESTING STANDARD METHOD TODETERMINE EFFICIENCY OFCOMMERCIAL SPACE HEATING BOILERSSCAQMD RULE 1146.2. EMISSIONS OF OXIDES OFNITROGEN FROM LARGE WATER HEATERS AND SMALLBOILERS AND PROCESS HEATERSCSD-1: CONTROLS AND SAFETY DEVICES FORAUTOMATICALLY FIRED BOILERS3.3 - PACKAGINGThe ALKON 90 boiler is supplied fully assembled in a strongcardboard box.After having unpacked the boiler check that it isintact and undamaged.CAUTIONKeep the packaging material (cardboard box,plastic bags, polyester protection etc.) out ofthe reach of children as they can bedangerous.LATTNER refuses all liability for injury topersons, animals or damage to propertyderiving from not having respected the abovementioned recommendations.56.3”1430 mmIn the packaging, in addition to the boiler, you can also findthe following contents:- Tecnical documetation set- Battery cover fixing kit (bag with notice - screws and verticalplates - cover plates)- Key and lock + pin kits- Connection kit drain pipe 3,9“ (100 mm)- Siphon connection kit (pipe pp)21.5”545 mm26.4”670 mmACAUTIONThe boiler may be damaged when not securedproperly.- Only transport the boiler using appropriate transportationequipment, such as a handtruck with a fastening belt orspecial equipment for maneuvering steps.- When shipping the boiler must be secured on the transportationequipment to prevent it from falling off.- Protect all parts against impacts if they are to be transported.- Follow the transportation markings on the packaging.• Packaged boilers must always be lifted and carried by twopeople, or you must use a handtruck or special equipmentfor transport.AEnvelope with adjustable feet, lock and key(placed on the pallet, inside the boiler).Remove screws ‘’A’’ to remove the boiler frompallet.14
Instructions for the installer- Remove the packaging materials.- Do not tear the packaging.- Take note of the necessary space around the boiler forinstallation of venting system, pipework and servicing. Seedrawing in section 3.4Mounting of the adjustable feetThe location of the boiler can be determined by using thedraw on page 16. Remember to account for the spacing of theplumbing kit.- Drill the necessary holes- Install the mounting bracket to the wall using the suppliedmounting materialsCAUTIONLifting and carrying precautions.To avoid personal injury please follow theserecommendations:- Always move the boiler with 2 people oruse special equipment.- When move the boiler, bend the knees, andkeep the back straight and feet apart.- Do not lift and twist at the same time.- Lift and carry the boiler close to the body.- Wear protective clothing and gloves to protectfrom any sharp edges.- Dispose the packaging materials.Before positioning the boiler, screw down theadjustable feet supplied with the boiler.Mounting of the lockerThe casing front panel is hinged on the R.H.side. The hinges ‘’A’’ are factory fitted on theR.H. side of the frame. For the introduction ofthe cocker remove the precut disk ‘’B’’ witha screwdriver and fit the cocker as shown inthe figure.AIn case the casing front panel needs to be hinged on theL.H. side, deplace the hinges ‘’A’’ from R.H. to L.H. side; thenremove the precut disk ‘’C’’ from the front panel and fit thelocker as shown in the figure.INTERNALSIDE OF THECASINGBEXTERNALSIDE OF THECASINGCBA15
Page 1 and 2: ®LATTNERCondensing gas boilerALKON
Page 3 and 4: General Information1 GENERAL INFORM
Page 5 and 6: General InformationDANGERSmell of g
Page 7 and 8: General Information1.8 - TOOLS, MAT
Page 9 and 10: 2.2 - DIMENSIONSTechnical features
Page 11 and 12: 2.4 - BOILER WATER CIRCUIT DIAGRAMT
Page 13: 3INSTRUCTIONS FORTHE INSTALLERInstr
Page 17 and 18: Instructions for the installer• D
Page 19 and 20: Instructions for the installer3.8 -
Page 21 and 22: Instructions for the installer3.10
Page 23 and 24: 3.14 - CONDENSATE DRAINDuring the c
Page 27 and 28: Instructions for the installerThe f
Page 29 and 30: 3.19 - ELECTRICAL CONNECTIONSRegula
Page 33 and 34: 3.22 - STARTING UP: Filling and de-
Page 39 and 40: 3.27 - PROGRAMMING OF THE OPERATING
Page 41 and 42: 4 INSPECTION AND SERVICING SCHEDULE
Page 43 and 44: Instructions for the installer4.5 -
Page 45 and 46: 5 FAULT FINDINGFault finding5.1 - E
Page 47 and 48: Spare parts6 SPARE PARTS15252224342
Page 49: Spare parts49

Installation Manual - Unical Lattner Condensing Hot Water Boilers

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?