INDUSTRIALInterior5/31/2012Rust-Stop DTM 100% Acrylic Latex Semi-GlossProduct Description:Ready to use odorless vinyl acrylic eggshell latex paint formulated for airless spray application on interior surfaces.Excellent for use over galvanized metal, aluminum, gypsum board, plaster, wood, masonry surfaces, and completelyprimed ferrous metal. These latex spray paints can be used as dry fall paints on ceilings 16 feet or higher when therelative humidity is less than 70%.Recommended Use:Ideal for wall and ceiling surfaces in industrial plants, commercial buildings, warehouses, public institutions, schoolsand churches.Application:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator tocontrol lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protectyourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on towww.epa.gov/lead.Surfaces must be clean, dry and free of dirt, dust and other contaminants.GALVANIZED METAL - Oil residue should be wiped off with mineral spirits with a clean rag.CONCRETE — Remove nibs and mortar splatter.FERROUS METAL — Must be completely primed with a rust inhibiting primerGYPSUM BOARD, PLASTER , WOOD — Fill cracks and voids with oil free patching compounds.PREVIOUSLY PAINTED SURFACES — These products are compatible with old finishes except water soluble paintssuch as calcimine or casein. Test questionable areas with a sponge and water. If water softens the surface, the oldfinish will have to be removed before finishing with latex.Architectural Specifications:▪ WOOD, CONCRETE, GYPSUM BOARD, PLASTER, MASONRY BOARD2 coats Premium Spray Eggshell▪ FERROUS METAL — Unprimed1 coat Prime Line Red Oxide Primer #17031 coat Premium Spray Eggshell▪ GALVANIZED METAL1 or 2 coats Premium Spray Eggshell▪ PREVIOUSLY PAINTED SURFACES1 coat Premium Spray EggshellPrecautions:High humidity or low temperatures will retard drying time. Do not use as a primer for other paints. Air and surfacetemperatures should be 50°F or higher during application and drying time. Do not use over unprimed ferrous metal.Safety Information:CONTAINS:NON VOLATILE VINYL-ACRYLIC RESINSCAUTION!:KEEP OUT OF THE REACH OF CHILDRENDO NOT TAKE INTERNALLY.CLOSE CONTAINER AFTER EACH USE.KEEP OUT OF REACH OF CHILDRENFOR INDUSTRIAL USE ONLYProduct Specifications:Type: Vinyl Acrylic LatexExposure:InteriorSpecular Gloss: 7 @ 60° ± 2Volume Solids: 32.5 % ±2Solids by Weight: 52.4 % ±2Vehicle: 56.2 % ±2Pigment: 43.8 % ±2Dry Film Thickness: 2.5 milsViscosity @ 77 °F:105KU ± 5Maximum VOC: 100 g/literFlash Pt °F: Non-combustibleThinner:WaterClean-Up: Soap & WaterAvailable Colors and Bases:WhiteAvailable Package Sizes:5 Gallon(Weight Per Gallon: 11.9 lbs. ± .5 lb)Drying Times:To Touch: 1-2 hrs.To Handle: 4 hrs.To Recoat: 2 hrs.(@ 70-77 °F, 50% R.H.)Surface Spread Rate:Smooth: 200 s.f./gal.Porous: 150 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Spray -Airless .015 to .018 Tip / 40-60° AnglesRoller -Brush on roller for smallareas only<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141
Product Description:Quick drying rust inhibiting acrylic latex flat primers/finishes for use over new or sound rusty ferrous metal surfacesfrom which mill scale and surface contaminants have been fully removed. Excellent for use over galvanized metal,aluminum, wood and masonry surfaces to be topcoated with latex, alkyd or oil modified urethane coatings.Recommended Use:Can be used successfully for priming miscellaneous iron, bar joists, ductwork, piping, galvanized metal, doors, sash,windows or for spot touching other abraded metal primers. May be used as a self-priming finish coat where a flatappearance is required.Application:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator tocontrol lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protectyourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on towww.epa.gov/lead.Remove all oil, grease, dirt, loose or scaling paint, rust, mill scale and other foreign matter.FERROUS METAL — "Power Tool" clean (SSPC-SP3) back to sound substrate.ALUMINUM - Unfinished aluminum should be wiped with mineral spirits on a clean rag to remove oil. Aluminum oxideon old weathered aluminum should be removed with steel wool and mineral spiritsGALVANIZED METAL — Oil residue should be wiped off with mineral spirits on a clean rag.PREVIOUSLY PAINTED SURFACES — Prepare ruptured or scratched surfaces as for unfinished metal. Spot primebare metal as conditions dictate.Architectural Specifications:▪ FERROUS METAL - PRECLEANED ALUMINUM, GALVANIZED METAL, WOOD OR MASONRY1 coat Rust-Stop DTM Acrylic Latex Flat Primer/Finish1 or 2 coats Alkyd Enamel, or Tuf-Quik® Oil Modified Urethane Enamel, or Rust-Stop DTM 100% Acrylic Latex MetalPaint▪ PREVIOUSLY PAINTED SURFACESSpot-prime bare metal areas with1 coat Rust-Stop DTM Acrylic Latex Flat Primer/Finish1 or 2 coats Alkyd Metal Primer, or Tuf-Quik® Oil Modified Urethane Enamel, or Rust-Stop DTM 100% Acrylic LatexMetal PaintExtremely rusty surfaces may require a second coat of Rust-Stop PrimerPrecautions:On bare ferrous metal Rust-Stop DTM Acrylic Latex 1061, 1064, 1067 must be used under #1092,1093,1094 and1095. Surface and air temperature must be 50°F or above during application and drying time. Do not recoat withcoatings using aromatic or other strong solvents. Do not intermix with solvent base primers or finishes. Use Rust-StopDTM Latex Flat Primer/Finish as a base coat under alkyd and oil modified urethane finishes. Do not use Rust-StopDTM 100% Acrylic Latex Metal Paint for thispurpose. Do not use Rust-Stop when rain is imminent or when dew point is above 60 percent. Rust-Stop is notdesigned for tank interiors or for immersion service.Safety Information:CAUTION! KEEP OUT OF THE REACH OF CHILDREN.DO NOT TAKE INTERNALLY.CLOSE CONTAINER AFTER EACH USE.*Specifications based on 1061 WhiteINDUSTRIALInterior or Exterior5/31/2012Rust-Stop® DTM Acrylic Latex Flat Primer/Finish1061, 64, 67Product Specifications:Type:Acrylic Latex*Exposure: Interior or ExteriorSpecular Gloss: 9 @ 60° ± 3Volume Solids: 38.2 % ±2Solids by Weight: 49.5 % ±2Vehicle: 79.2 % ±2Pigment: 20.8 % ±2Dry Film Thickness: 1.5 milsViscosity @ 77 °F: 80KU ± 5Maximum VOC: 100 g/literFlash Pt °F: Non-combustibleThinner:WaterClean-Up: Soap & WaterAvailable Colors and Bases:WhiteGrayRedAvailable Package Sizes:Quart Gallon 5 Gallon(Weight Per Gallon: 10.2 lbs. ± .5 lb)Drying Times:To Touch: 2 hrs.To Handle: 2 hrs.To Recoat: 2 hrs.(@ 70-77 °F, 50% R.H.)Surface Spread Rate:Smooth: 400-425s.f./gal.Porous: 275-325 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Brush -Synthetic, Nylon or PolyesterRoller -3/8" Nap Synthetic FiberAirless Spray -.017 to .019 Tip<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141