Product Description:Prime Choice Alkyd Primer/Sealer/Undercoater & Vapor Barrier is a smooth flowing pigmented interior oil basedprimer formulated to seal highly absorbent wall and ceiling surfaces. This product provides excellent holdout for interiorsurfaces to be topcoated with enamels. It sands easily and provides a superior basecoat for very smooth finish work.The superior sealing qualities of this primer will eliminate "flashing" on cured plaster surfaces that are to be topcoatedwith eggshell, semi-gloss or gloss finishes. This primer can be used as a sealer over surfaces that have suffered fromfire, smoke or water damage.Recommended Use:Plaster, wood, drywall, composition board. The high binder content of this primer makes it ideal for sealing deterioratedold finishes that are checked, cracked or have been partially removed before finish coats of other paints are applied.Prime Choice Alkyd Primer/Sealer/ Undercoater & Vapor Barrier resists vapor transmission and meets FHA and H.U.D.vapor barrier requirements for interior surfaces of exterior walls (ASTM E96-66 rating = 0.85 "Perms"). This is also asuperior product for sealing any surface to which wallcoverings will be applied. Wallcoverings can be removed at afuture date without damaging the sheetrock or skimcoat plaster substrate. This primer can also be used as a sealerover surfaces that have suffered from fire, smoke or water damage.Application:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to controllead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect yourselfand your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on towww.epa.gov/lead.Surfaces to be painted must be free of dust, mildew, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap, andother surface contamination. Patch irregularities with vinyl patching paste or an appropriate patching compound.Wallboard or Sheetrock - Tape joints should be sanded before priming, with care being exersized to prevent abrasion ofthe adjacent paper surface.Plaster, Veneer Plaster (Blueboard) - New plaster must be fully cured and should be wiped with a wet sponge toneutralize any "hot spots". The moisture content should be below 15%. Full plaster requires a minimum of 30 days,skimcoat plaster a minimum of 10 days to cure. Nibs should be knifed off before priming. Do not sand until aftersurface is primed. Prime Choice Alkyd Primer/Sealer/Undercoater & Vapor Barrier is best applied by brush or roller.This product is of proper consistency as packaged to be applied without thinning under normal environmental andapplication conditions. Clean tools and equipment as soon as possible with mineral spirits. This primer-sealer can betinted with up to 2 oz. <strong>California</strong> Universal Colorants to insure proper hiding. After primer-sealer has properly dried,lightly sand and dust surfaces before finish coating.Architectural Specifications:▪ Plaster, Wallboard, Sheetrock, Composition Board, Wood:1 Coat Prime Choice Alkyd Primer/Sealer/Undercoater & Vapor Barrier 202001 or 2 coats Alkyd, Latex or Oil Modified Urethane in desired finishFIRE RATING CLASS A (DRY FILM) Test Method ASTM E84 Flame Spread 5 Smoke Density 0Precautions:Do not thin with water or mix with other type paints. Air and surface temperatures should be at least 50ºF duringapplication and drying time. High humidity and inadequate ventilation will increase drying time required before finishcoats can be applied. Wash new plaster with clean water, rinsing rags or sponges frequently. New plaster should bethoroughly dry before priming is started. A moisture content of 15% or less is required to avoid peeling problems. Skimcoat plaster requires a minimum of 10 days to properly cure, full plaster requires a minimum of 30 days. Prime ChoiceAlkyd Primer/Sealer/Undercoater & Vapor Barrier will raise the nap of new sheetrock slightly. Surfaces should besanded before finishing.Safety Information:Keep out of reach of children. Do not take internally. Close container after each use.This product contains more than 0.1% crystalline silica (CAS No. 14808-60-07) which has been classified by IARC as aClass 1 carcinogen. Normal application procedures pose no hazard since the silica is wet and encapsulated, butgrinding or sanding dried films may yield respirable silica dusts. Control exposures to less than 0.1 mg/m³ using NIOSHapproved dust filter respirators.DATA/SPECIFICATIONS 9R0016PRIME CHOICEPRIMER/SEALER/UNDERCOATER & VAPOR BARRIOR 20200Product Specifications:Type:AlkydExposure:InteriorSpecular Gloss: 2 @ 60° ± 2Volume Solids: 56.3 % ±2Solids by Weight: 75.4 % ±2Vehicle: 50.7 % ±2Pigment: 49.3 % ±2Dry Film Thickness: 2.1 milsViscosity @ 77 °F: 82 KU ±5Maximum VOC: 350 g/literFlash Pt °F: 103Thinner: Mineral SpiritsClean Up: Mineral SpiritsAvailable Colors and Bases:WhiteAvailable Package Sizes:Quart Gallon 2 Gallon5 Gallon(Weight Per Gallon: 11.4 lbs. ± .5 lb)Drying Times:To Touch: 4 hrs.To Handle: 10 hrs.To Recoat: 24 hrs.(@ 70-77 °F, 50% R.H.)Surface Spread Rate:Smooth: 400-450s.f./gal.Porous: 250-350 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Brush -Synthetic, Nylon or PolyesterCAUTION: COMBUSTIBLE! CONTAINS: PETROLEUM DISTILLATE Keep away from heat and flame. To avoidbreathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during applicationand drying. If you experience eye watering, headache or diziness, increase fresh air or wear respiratory protection(NIOSH/MSHA TC 23C or equivalent) or leave the area. Close container after each use. Avoid contact with skin. Usewith adequate ventilation. FIRST AID: In case of eye contact, flush immediately with plenty of water for at least 15minutes and call a physician. For skin, wash thoroughly with soap and water. If swallowed, call a physicianimmediately. Never give anything by mouth to an unconscious person. Remove contaminated clothing includingshoes. Wash clothing before re-use. Discard contaminated shoes. NOTICE: Reports have associated repeated andprolonged occupational over-exposure to solvents with permanent brain and nervous system damage. Intentionalmisuse by deliberately concentrating and inhaling the contents may be harmful or fatal.Roller -Short Nap Synthetic orNatural FiberAirless Spray -.011 to .013 Tip<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141
Product Description:This premium quality, very low odor, fast dry white primer-sealer is an interior undercoater that prevents the migrationof bleeding stains that show through other primers. Seals water stains on plaster, ceiling tile and sheetrock aftereliminating the moisture source and allowing them to dry. Soot damage and smoke residue that remain after washingor solvent cleaning can be sealed with this product prior to repainting.Recommended Use:Sheetrock, plaster, wallboard, interior wood trim, primed metalApplication:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to controllead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect yourselfand your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on towww.epa.gov/lead.Surfaces to be painted must be clean, dry and free of contaminants such as dust, dirt, oil, grease, wax, loose paint,rust and mill scale. Mildew must be killed by scrubbing with a solution of equal parts household bleach and water.Rinse with clean water and allow to dry. Glossy surfaces should be dulled by sanding and the dust removed.Weathered or abraded wood or any unsound substrates should be sanded back to a paintable surface. After removingrust, prime ferrous metal with a rust inhibiting primer.DATA/SPECIFICATIONS 910/30/2009PRIME CHOICELow Odor Primer/Sealer/Stain Killer 20700Product Specifications:Type:AlkydExposure: InteriorSpecular Gloss: 2 @ 60° ± 2Volume Solids: 52.2 % ±2Solids by Weight: 77.7 % ±2Vehicle: 30.7 % ±2Pigment: 69.3 % ±2Dry Film Thickness: 2.1 milsViscosity @ 77 °F: 82 KU ±5Maximum VOC: 350g/literFlash Pt °F: 103Thinner: Mineral SpiritsClean Up: Mineral SpiritsAvailable Colors and Bases:WhiteThis product should be applied liberally and evenly by brush, roller or spray. In extreme conditions or on poroussurfaces a second coat may be necessary. This material is supplied at proper consistency. Use mineral spirits foreasy clean up of paint tools and equipment immediately after job is completed.Architectural Specifications:▪ Plaster, Wallboard, Sheetrock, Primed Metal, Wood, Aluminum:1 Coat Prime Choice Low Odor Primer/Sealer/Stain Killer 207001 or 2 coats <strong>California</strong> Latex finishNotes:1. If used as a spot primer on bare interior surfaces, a full coat of the proper primer should be applied before the finishcoat.2. Not recommended for use under organic solvent thinned paints.Precautions:Do not mix with water, oils, other paint types. This is not a vapor barrier and therefore is not suitable for use underwallpaper. Should be topcoated only with latex finish coats as some oil based paints will dissolve this primer. Air andsurface temperature should be 50ºF or more during application and drying times. Do not use when rain is imminent oron humid or foggy days. Use only the specified thinners. Do not mix with water, oils or other paints or solvents. Donot mix with Universal Colorants.Safety Information:CAUTION! COMBUSTIBLE!CONTAINS: PETROLEUM DISTILLATE Keep away from heat and flame. To avoid breathing vapors or spray mist,open windows and doors or use other means to ensure fresh air entry during application and drying. If you experienceeye watering, headache or diziness, increase fresh air or wear respiratory protection (NIOSH/MSHA TC 23C orequivalent) or leave the area. Close container after each use. Avoid contact with skin. Use only with adequateventilation. Keep out of reach of children. Do not take internally.FIRST AID: If swallowed, do not induce vomiting. Call physician immediately.Available Package Sizes:Quart Gallon 5 Gallon(Weight Per Gallon: 13.5 lbs. ± .5 lb)Drying Times:To Touch: .5 hrs.To Handle: 1 hrs.To Recoat: 2 hrs.(@ 70-77 °F, 50% R.H.)Surface Spread Rate:Smooth: 400-500 s.f./gal.Porous: 200-275 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Brush -Synthetic, Nylon or PolyesterRoller -3/8" Nap Synthetic FiberAirless Spray -.017 to .019 Tip<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141
Change language