Product Description:Paint & Primer in OneInteriorFres~Coat Unite Paint and Primer in One is a premium smooth flowing, quick drying latex semi-gloss finish paint thatis used for interior walls and ceilings. This product contains a self priming feature that will make any paint job go fasterin less coats and look better than conventional latex paints. Unite Semi-Gloss is a durable anti-spatter finish that willwithstant repeated scrubbingRecommended Use:Plaster, sheetrock, wallboard, concrete, masonry block, wood, primed metal, galvanized metal.Fres~Coat Unite 100% Acrylic Semi-Gloss EnamelApplication:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator tocontrol lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protectyourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on towww.epa.gov/lead.Surfaces to be painted must be free of dust, mildew, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap, andother surface contamination. Patch irregularities with vinyl patching paste or an appropriate patching compound.Fres~Coat 100% Acrylic Latex Semi-Gloss is self-priming over bare sheetrock, composition board, ceiling tile andconcrete.Plaster, Veneer Plaster (Blueboard) - New plaster must be fully cured and should be wiped with a wet sponge toneutralize any "hot spots". The moisture content should be below 15%. Full plaster requires a minimum of 30 days,skim coat plaster a minimum of 10 days to cure. Nibs should be knifed off before painting. Do not sand until after thesurface is painted.Ferrous Metal - Clean, then prime with Rust Stop® Rust Inhibiting Metal Primer.New Wood - Knots and stains should be sealed with Prime Choice® Oil Based Stain-blocking Primer #20700 or PrimeChoice Universal Latex Stain-blocking Primer #50600 to avoid staining. All wood should then be primed with <strong>California</strong>Prime Choice Alkyd Primer-sealer #20200 or Prime Choice Latex All Surface Primer #50300.Masonry Block - Apply one coat of Mason-Cote® Block Filler 3751 if a denser surface is desired.Disposal: For recycling guidance of any unused amount, contact your local or provincial organization of recovery andrecycling. Dry, empty containers may be recycled in a can recycling program where facilities are available.5/31/2012563XXProduct Specifications:Type: *100% Acrylic LatexExposure:InteriorSpecular Gloss: 45@ 60° ± 5Volume Solids: 30.9 % ±2Solids by Weight: 43.6 % ±2Vehicle: 78.5 % ±2Pigment: 21.5 % ±2Dry Film Thickness: 1.2 milsViscosity @ 77 °F: 98KU ± 3Maximum VOC: **150 g/literFlash Pt °F: Non-combustibleThinner:WaterClean-Up: Soap & WaterAvailable Colors and Bases:WhitePastelNeutralMediumDeepBlackSuper Hide WhiteAvailable Package Sizes:Quart Gallon 5 Gallon**Information on EU VOC (Calculated differently from US Method): MAXIMUM VOC (As used) Based on EU CatergoryA/d: 130 g/l Per EU Method Directive 2004/42/CEArchitectural Specifications:▪ Plaster, Wallboard, Sheetrock:2 coats Fres~Coat Unite100% Acrylic Waterborne Semi-Gloss 563XX▪ Concrete, Non-Porous Masonry:2 coats Fres~Coat Unite 100% Acrylic Waterborne Semi-Gloss 563XX▪ Porous Masonry and Block:1 coat Mason-Cote® Block Filler 37511 or 2 coats Fres~Coat Unite 100% Acrylic Waterborne Semi-Gloss 563XX▪ Ferrous Metal - Un-primed:1 coat Rust Stop® Rust Inhibiting Metal Primer 211501 or 2 coats Fres~Coat Unite 100% Acrylic Waterborne Semi-Gloss 563XX▪ Ferrous Metal - Primed, Galvanized Metal:2 coats Fres~Coat Unite 100% Acrylic Waterborne Semi-Gloss 563XX▪ Wood:1 coat Prime Choice All Surface Acrylic Primer 50300 (see above comments on "New Wood")1 or 2 coats Fres~Coat Unite 100% Acrylic Waterborne Semi-Gloss 563XX▪ Acoustical Tile:2 coats Fres~Coat Unite 100% Acrylic Waterborne Semi-Gloss 563XXPrecautions:Do not add solvents, oils or colors in oil, or mix with other paint types. Do not apply when air or surface temperature isbelow 50° F or when drying conditions are poor. Keep from freezing. Use adequate ventilation. All colors should beapplied on a small area allowed to dry and approved for accuracy before doing the job.Safety Information:Keep out of reach of children. Do not take internally. Close container after each use.*Specification data based on the Pastel Base: 56391(Weight Per Gallon: 10.2 lbs. ± .5 lb)Drying Times:To Touch: 1 hrs.To Handle: 8 hrs.To Recoat: 2 hrs.Surface Spread Rate:Smooth: 400-450s.f./gal.Porous: 300-350 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Brush -Synthetic, Nylon or PolyesterRoller -(@ 70-77 °F, 50% R.H.)3/8" Nap Synthetic FiberAirless Spray -.017 to .019 Tip<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141
Product Description:SELF-PRIMINGInteriorSuper-Scrub Ceramic Eggshell Finish incorporates the latest technology in its formulation to produce the highestquality, most durable paint on the market today. Super Scrub’s anti spatter formulation sets the standard for ease ofapplication, flow, leveling and adhesion. It provides excellent color retention, moisture resistance and scrubbability,making it the ideal coating for any room in the home, office, or commercial building. Ceramic microspheresincorporated with 100% acrylic waterborne technology make it highly stain resistant. Super Scrub Ceramic 100%acrylic Eggshell contains Microban® antimicrobial protection. This unique additive will inhibit the growth of stain andodor causing bacterial; mold, mildew and other fungal growth on the dried paint film. Microban protection provides anadded level of protection between cleanings, but does not take the place of normal cleaning and disinfectingprocedures and will not protect against food borne illness. Microban additives are E.P.A. registered for use in paint.For more information visit www.microban.com.Recommended Use:Plaster, sheetrock, wallboard, concrete, masonry block, wood, primed metal, galvanized metal, acoustical surfaces.Application:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator tocontrol lead exposure.Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protectyourself and your familyby contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on to www.epa.gov/lead.Super-Scrub Ceramic Eggshell Finish requires thorough stirring prior to application. Surfaces to be painted must befree of dust, mildew, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap, and other surface contamination.Patch irregularities with vinyl patching paste or an appropriate patching compound. 2010 Super-Scrub Ceramic MatteFinish is self-priming over bare sheetrock, composition board, ceiling tile and concrete.Plaster, Veneer Plaster (Blueboard) - New Plaster must be fully cured and should be wiped with wet sponge toneutralize any "hot spots". The moisture content should be below 15%. Full plaster requires a minimum of 30 days,skim coat plaster a minimum of 10 days to cure. Nibs should be knifed off before painting. Do not sand until after thesurface is painted.Ferrous Metal - Clean, then prime with Rust Stop® Rust Inhibiting Metal Primer.New Wood - Knots and stains should be sealed with Prime Choice® Oil Based Stain-blocking Primer #20700 or PrimeChoice Universal Latex Stain-blocking Primer #50600 to avoid staining. All wood should then be primed with <strong>California</strong>Prime Choice Alkyd Primer-sealer #20200 or Prime Choice Latex All Surface Primer #50300.Masonry Block - Apply one coat of Mason-Cote Block Filler 3751 if a denser surface is desired.DISPOSAL: For recycling guidance of any unused amount, contact your local or provincial organization of recoveryand recycling. Dry, empty containers may be recycled in a can recycling program where facilities are available.Architectural Specifications:▪ Plaster, Wallboard, Sheetrock:2 coats Super-Scrub Ceramic 100% Acrylic Eggshell 551XX▪ Concrete, Non-Porous Masonry:2 coats Super-Scrub Ceramic 100% Acrylic Eggshell 551XX▪ Porous Masonry and Block:1 coat Mason-Cote® Block Filler 37512 coats Super-Scrub Ceramic 100% Acrylic Eggshell 551XX▪ Ferrous Metal - Un-primed:1 coat Rust Stop® Rust Inhibiting Metal Primer 211502 coats Super-Scrub Ceramic 100% Acrylic Eggshell 551XX▪ Ferrous Metal - Primed, Galvanized Metal:2 coats Super-Scrub Ceramic 100% Acrylic Eggshell 551XX▪ Wood:1 coat Prime Choice All Surface Acrylic Primer 50300 (see above comments on "New Wood")2 coats Super-Scrub Ceramic 100% Acrylic Eggshell 551XX▪ Acoustical Tile:2 coats Super-Scrub Ceramic 100% Acrylic Eggshell 551XXPrecautions:Do not add solvents, oils or colors in oil, or mix with other paint types. Do not apply when air or surface temperature isbelow 50° F or when drying conditions are poor. Keep from freezing. Use adequate ventilation.Safety Information:Keep out of reach of children. Do not take internally. Close container after each use.*Specification data based on the pastel base: 55391**Information on EU VOC (Calculated differently from US Method): MAXIMUM VOC (As used) Based on EU CategoryA/d: 130 g/l Per EU Method Directive 2004/42/C<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-11415/31/2012Super-Scrub® Ceramic Eggshell FinishWith Microban® 551XXProduct Specifications:Type: *100% Acrylic LatexExposure:InteriorSpecular Gloss: 11@ 60° ± 3Volume Solids: 28.8 % ±2Solids by Weight: 43.4 % ±2Vehicle: 72.7 % ±2Pigment: 27.3 % ±2Dry Film Thickness: 1.1 milsViscosity @ 77 °F: 93KU ± 3Maximum VOC: **150 g/literFlash Pt °F: Non-combustibleThinner:WaterClean-Up: Soap & WaterAvailable Colors and Bases:WhiteMediumNeutralPastelDeepAvailable Package Sizes:Quart Gallon 5 Gallon(Weight Per Gallon: 10.5 lbs. ± .5 lb)Drying Times:To Touch: 1 hrs.To Handle: 8 hrs.To Recoat: 2 hrs.Surface Spread Rate:Smooth: 400-450s.f./gal.Porous: 300-350 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Brush -Synthetic, Nylon or PolyesterRoller -(@ 70-77 °F, 50% R.H.)3/8" Nap Synthetic FiberAirless Spray -.017 to .019 Tip