CompleteSpecManual - California Paints

Product Description:InteriorThis heavy bodied white 100% acrylic latex texture paint can be used to create a unique and distinctive sand plasterfinish. It will mask hair line cracks and imperfections and may be painted over with any latex to provide a colored sandfinish.Recommended Use:Plaster, sheetrock, wallboard, masonry, plywood.Application:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator tocontrol lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protectyourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on towww.epa.gov/lead.Surfaces to be painted must be free of dust, mildew, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap, andother surface contamination. Patch irregularities with vinyl patching paste or an appropriate patching compound. SandFinish is self-priming over bare sheetrock, composition board, ceiling tile and concrete.New Plaster - Knife off all nibs and protrusions. Wipe with a clean damp cloth to remove loose particles. Do not sandnew plaster until it is primed.Wallboard, Sheetrock, Gypsum Board - Joint compound should be sanded smooth, but avoid abrading the paper.Ferrous Metal - Clean, then prime with Larcoloid ® Rust Inhibiting Metal PrimerWood - Seal knots and stains with Prime Choice Low Odor Oil Base Primer Sealer or Prime Choice 100% AcrylicUniversal PrimerMasonry Block - Apply one coat of Mason-Cote® Block Filler 3751 if a denser surface is desired.Previously Painted Surfaces - Wash, sand or dust to obtain a paintable surface.Glossy Surfaces - Dull by sanding to insure proper adhesion of paint.Architectural Specifications:▪ Plaster, Wallboard, Sheetrock, Concrete, Non-Porous Masonry:1 coat Prime Choice All Surface Acrylic Primer 503001 coat Sand Finish 56500or2 coats Sand Finish 56500▪ Porous Masonry and Block:1 coat Mason-Cote® Block Filler 37511 or 2 coats Sand Finish▪ Wood:1 coat Prime Choice All Surface Acrylic Primer 503001 or 2 coats Sand FinishNote: If a distinctive or different texture is desired, a small test patch should be done to determine the desiredappearance.Precautions:Do not add solvents, oils or colors in oil, or mix with other paint types. Do not apply when air or surface temperature isbelow 50° F or when drying conditions are poor. Keep from freezing.Safety Information:Keep out of reach of children. Do not take internally. Close container after each use.5/31/2012Sand Finish 100% Acrylic Latex56500Product Specifications:Type: 100% Acrylic LatexExposure:InteriorSpecular Gloss: 2 @ 60° ± 2Volume Solids: 47.4 % ±2Solids by Weight: 67.3 % ±2Vehicle: 42.3 % ±2Pigment: 57.7 % ±2Dry Film Thickness: 8 milsViscosity @ 77 °F: 80-90 KU ± 5Maximum VOC: 300 g/literFlash Pt °F: Non-combustibleThinner:WaterClean-Up: Soap & WaterAvailable Colors and Bases:WhiteAvailable Package Sizes:Gallon5 Gallon(Weight Per Gallon: 13.5 lbs. ± .5 lb)Drying Times:To Touch: 1 hrs.To Handle: 4 hrs.To Recoat: 2 hrs.(@ 70-77 °F, 50% R.H.)Surface Spread Rate:Smooth: 90-110s.f./gal.Porous: 70-90 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Brush -White FiberRoller -Stipple, Long nap, TexturingtoolsCalifornia Paints ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141