Product Description:InteriorProPaint Alkyd Semi-Gloss White is an economical yet durable enamel designed for interior use on trim, walls,cabinets and furniture. It is specially formulated to provide a tough, scrubbable finish and is ideal for such areas askitchens, baths, hallways, playrooms and other high service areas.Recommended Use:Sheetrock, plaster, wallboard, concrete block, primed wood, primed metal.Application:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator tocontrol lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protectyourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on towww.epa.gov/lead.Surfaces to be painted must be free of dust, mildew, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap, andother surface contamination. Patch irregularities with vinyl patching paste or an appropriate patching compound.5/31/2012ProPaint® Alkyd Semi-Gloss White23500Product Specifications:Type:AlkydExposure:InteriorSpecular Gloss: 57@ 60° ± 5Volume Solids: 51.2 % ±2Solids by Weight: 69.0 % ±2Vehicle: 64.3 % ±2Pigment: 35.7 % ±2Dry Film Thickness: 2 milsViscosity @ 77 °F: 87KU ± 5Maximum VOC: 380 g/literFlash Pt °F: 103Thinner: Mineral SpiritsClean-Up: Mineral SpiritsPlaster, Veneer Plaster (Blueboard) - New plaster must be fully cured and should be wiped with a wet sponge toneutralize any “hot spots”. The moisture content should be below 15%. Full plaster requires a minimum of 30 days,skim coat plaster a minimum of 10 days to cure. Nibs should be knifed off before priming. Do not sand until after thesurface is primed. Prime with Prime Touch Professional Acrylic Latex Primer/Sealer.Wallboard, Sheetrock, Gypsum Board - Joint compound should be sanded smooth, but avoid abrading the paper.Wood - Seal knots and stains with Prime Choice Low Odor Oil Base Primer Sealer or Prime Choice 100% AcrylicUniversal Primer Then prime with Prime Touch Professional Acrylic Latex Primer/Sealer.Ferrous Metal - Clean, then prime with Larcoloid® Rust Inhibiting Metal Primer.Glossy Surfaces - Dull surface by sanding to insure adhesion of paint.Masonry Block - Apply one coat of ProPaint Block Filler 51500 if a denser surface is desired.Previously Painted Surfaces - Wash, sand, or dust to obtain proper adhesion of paint.Architectural Specifications:▪ Plaster, Wallboard, Sheetrock:1 coat Prime Touch Professional Acrylic Latex Primer/Sealer 545001 or 2 coats ProPrime Alkyd Semi-Gloss White 23500▪ Concrete, Non-Porous Masonry:1 coat Prime Touch Professional Acrylic Latex Primer/Sealer 545001 or 2 coats ProPrime Alkyd Semi-Gloss White 23500▪ Porous Masonry and Block:1 coat ProPaint Block Filler 515001 or 2 coats ProPrime Alkyd Semi-Gloss White 23500▪ Ferrous Metal - Un-primed:1 coat Larcoloid® Rust Inhibiting Metal Primer 211501 or 2 coats ProPrime Alkyd Semi-Gloss White 23500▪ Wood:1 coat Prime Touch Professional Acrylic Latex Primer/Sealer 545001 or 2 coats ProPrime Alkyd Semi-Gloss White 23500Precautions:Do not apply when air or surface temperature is below 50° F or when moisture is evident. Do not mix with latex paint.Inadequate ventilation will retard drying time. Two thin coats provides a better finish than one thick coat.Safety Information:CAUTION! COMBUSTIBLE! Use only with adequate ventilation. Keep out of reach of children. Do not takeinternally. Close container after each use.Available Colors and Bases:WhiteAvailable Package Sizes:Gallon(Weight Per Gallon: 10.1 lbs. ± .5 lb)Drying Times:To Touch: 4 hrs.To Handle: 6 hrs.To Recoat: 16 hrs.(@ 70-77 °F, 50% R.H.)Surface Spread Rate:Smooth: 400-450s.f./gal.Porous: 250-350 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Brush -Natural BristleRoller -Short Nap Synthetic orNatural FiberAirless Spray -.011 to .013 Tip<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141
Product Description:InteriorThis is the most economical of primers designed as a first coat on bare surfaces to be topcoated with Preference Flat.Recommended Use:Wallboard, Sheetrock, Concrete, Masonry BlockApplication:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator tocontrol lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protectyourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on towww.epa.gov/lead.Surfaces to be painted must be free of dust, mildew, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap, andother surface contamination. Patch irregularities with vinyl patching paste or an appropriate patching compound.Wallboard, Sheetrock, Gypsum Board - Joint compound should be sanded smooth, but avoid abrading the paper.Ferrous Metal - Clean, then prime with Larcoloid® Rust Inhibiting Metal PrimerWood - Seal knots and stains with Prime Choice Low Odor Oil Base Primer Sealer or Prime Choice 100% AcrylicUniversal Primer.Masonry Block - Apply one coat of Mason-Cote® Block Filler 3751 if a denser surface is desired.Architectural Specifications:▪ Wallboard, Sheetrock, Concrete, Masonry, Wood, Acoustical Tile:1 coat Preference Primer 500001 or 2 coats Preference Flat or Contractor FlatPrecautions:Do not add solvents, oils or colors in oil, or mix with other paint types. Do not use in areas subject to continuousdampness. Do not apply when air or surface temperature is below 50° F or when drying conditions are poor. Keep fromfreezing. Do not use this product under oil base products, first line latex products or products with any degree of gloss.Safety Information:Keep out of reach of children. Do not take internally. Close container after each use.5/31/2012Preference Primer50000Product Specifications:Type: Vinyl Acrylic LatexExposure:InteriorSpecular Gloss: 2 @ 60° ± 2Volume Solids: 31.4 % ±2Solids by Weight: 52.1 % ±2Vehicle: 53.9 % ±2Pigment: 46.2 % ±2Dry Film Thickness: 1.5 milsViscosity @ 77 °F:100KU ± 5Maximum VOC: 100 g/literFlash Pt °F: Non-combustibleThinner:WaterClean-Up: Soap & WaterAvailable Colors and Bases:WhiteAvailable Package Sizes:Gallon 5 Gallon(Weight Per Gallon: 12.0 lbs. ± .5 lb)Drying Times:To Touch: 1 hrs.To Handle: 3 hrs.To Recoat: 4 hrs.(@ 70-77 °F, 50% R.H.)Surface Spread Rate:Smooth: 300-350s.f./gal.Porous: 225-275 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Brush -Synthetic Nylon or PolyesterRoller -3/8 Nap Synthetic FiberAirless Spray -Airless .017-.019 Tip<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141