Product Description:SELF-PRIMINGInteriorSuper-Scrub Ceramic Matte Finish incorporates the latest technology in its formulation to produce the highest quality,most durable paint on the market today. Super Scrub’s anti spatter formulation sets the standard for ease ofapplication, flow, leveling and adhesion. It provides excellent color retention, moisture resistance and scrubbability,making it the ideal coating for any room in the home, office, or commercial building. Ceramic microspheresincorporated with 100% acrylic waterborne technology make it highly stain resistant. Super Scrub Ceramic 100%acrylic Matte contains Microban® antimicrobial protection. This unique additive will inhibit the growth of stain and odorcausing bacterial; mold, mildew and other fungal growth on the dried paint film. Microban protection provides an addedlevel of protection between cleanings, but does not take the place of normal cleaning and disinfecting procedures andwill not protect against food borne illness. Microban additives are E.P.A. registered for use in paint. For moreinformation visit www.microban.com.Recommended Use:Plaster, sheetrock, wallboard, concrete, masonry block, wood, primed metal, galvanized metal, acoustical surfaces.Application:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator tocontrol lead exposure.Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protectyourself and your familyby contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on to www.epa.gov/lead.Super-Scrub Ceramic Matte Finish requires thorough stirring prior to application. Surfaces to be painted must be freeof dust, mildew, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap, and other surface contamination. Patchirregularities with vinyl patching paste or an appropriate patching compound. 2010 Super-Scrub Ceramic Matte Finishis self-priming over bare sheetrock, composition board, ceiling tile and concrete.Plaster, Veneer Plaster (Blueboard) - New Plaster must be fully cured and should be wiped with wet sponge toneutralize any "hot spots". The moisture content should be below 15%. Full plaster requires a minimum of 30 days,skim coat plaster a minimum of 10 days to cure. Nibs should be knifed off before painting. Do not sand until after thesurface is painted.Ferrous Metal - Clean, then prime with Rust Stop® Rust Inhibiting Metal Primer.New Wood - Knots and stains should be sealed with Prime Choice® Oil Based Stain-blocking Primer #20700 or PrimeChoice Universal Latex Stain-blocking Primer #50600 to avoid staining. All wood should then be primed with <strong>California</strong>Prime Choice Alkyd Primer-sealer #20200 or Prime Choice Latex All Surface Primer #50300.Masonry Block - Apply one coat of Mason-Cote Block Filler 3751 if a denser surface is desired.DISPOSAL: For recycling guidance of any unused amount, contact your local or provincial organization of recoveryand recycling. Dry, empty containers may be recycled in a can recycling program where facilities are available.Architectural Specifications:▪ Plaster, Wallboard, Sheetrock: 2 coats Super-Scrub Ceramic Matte Finish▪ Concrete, Non-Porous Masonry: 2 coats Super-Scrub Ceramic Matte Finish▪ Porous Masonry and Block: 1 coat Mason-Cote® Block Filler 37511 or 2 coats Super-Scrub Ceramic Matte Finish▪ Ferrous Metal - Un-primed: 1 coat Rust Stop® Rust Inhibiting Metal Primer1 or 2 coats Super-Scrub Ceramic Matte Finish▪ Ferrous Metal - Primed, Galvanized Metal:2 coats Super-Scrub Ceramic Matte Finish▪ Wood:1 coat Prime Choice All Surface Acrylic Primer 50300 (see above comments on "New Wood")1 or 2 coats Super-Scrub Ceramic Matte Finish▪ Acoustical Tile:2 coats Super-Scrub Ceramic Matte FinishPrecautions:Do not add solvents, oils or colors in oil, or mix with other paint types. Do not apply when air or surface temperature isbelow 50° F or when drying conditions are poor. Keep from freezing. Use adequate ventilation.Safety Information:Keep out of reach of children. Do not take internally. Close container after each use.*Specification data based on the pastel base: 55391**Information on EU VOC (Calculated differently from US Method): MAXIMUM VOC (As used) Based on EU CategoryA/a: 30 g/l Per EU Method Directive 2004/42/C5/31/2012Super-Scrub® Ceramic Matte FinishWith Microban® 553XXProduct Specifications:Type: *100% Acrylic LatexExposure:InteriorSpecular Gloss: 2 @ 60° ± 2Volume Solids: 28.2 % ±2Solids by Weight: 44.7 % ±2Vehicle: 68.8 % ±2Pigment: 31.2 % ±2Dry Film Thickness: 1 milsViscosity @ 77 °F: 93KU ± 3Maximum VOC: **50 g/literFlash Pt °F: Non-combustibleThinner:WaterClean-Up: Soap & WaterAvailable Colors and Bases:WhiteMediumNeutralPastelDeepAvailable Package Sizes:Quart Gallon 5 Gallon(Weight Per Gallon: 10.8 lbs. ± .5 lb)Drying Times:To Touch: 1 hrs.To Handle: 4 hrs.To Recoat: 2 hrs.Surface Spread Rate:Smooth: 400-450s.f./gal.Porous: 300-350 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Brush -Synthetic, Nylon or PolyesterRoller -(@ 70-77 °F, 50% R.H.)3/8" Nap Synthetic FiberAirless Spray -.017 to .019 Tip<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141
Product Description:InteriorCal Pro 2000 Series is a smooth flowing anti-spatter flat finish for use on walls and ceilings in homes, apartments,condominiums and commercial applications. Cal Pro 2000 Series is easily applied, dries quickly, and providesexcellent hiding for most new and previously painted surfaces and can be applied by brush, roller or spray.Recommended Use:Plaster, sheetrock, wallboard, concrete, masonry block, wood, primed metal, primed galvanized metal, acousticalsurfaces.Application:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator tocontrol lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protectyourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424- LEAD (5323) or log on towww.epa.gov/lead.Surfaces to be painted must be free of dust, mildew, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap, andother surface contamination. Patch irregularities with vinyl patching paste or an appropriate patching compound. CalPro 2000 Series Acrylic Flat is self-priming over bare sheetrock, composition board, ceiling tile and concrete.New Plaster - Knife off all nibs and protrusions. Wipe with a clean damp cloth to remove loose particles. Do not sandnew plaster until it is primed.Wallboard, Sheetrock, Gypsum Board - Joint compound should be sanded smooth, but avoid abrading the paper.Ferrous Metal, Galvanized Metal - Clean, then prime with Everlife Rust Inhibiting Metal Primer.Wood - Seal knots and stains with Prime Choice Low Odor Oil Base Primer Sealer or Prime Choice 100% AcrylicUniversal Primer.Masonry Block - Apply one coat of Mason-Cote® Block Filler 3751 if a denser surface is desired.DISPOSAL: For recycling guidance of any unused amount, contact your local or provincial organization of recoveryand recycling. Dry, empty containers may be recycled in a can recycling program where facilities are available.Architectural Specifications:▪ Plaster, Wallboard, Sheetrock:2 coats Cal Pro 2000 Series Acrylic Flat 556XX▪ Concrete, Non-Porous Masonry:2 coats Cal Pro 2000 Series Acrylic Flat 556XX▪ Porous Masonry and Block:1 coat ProPaint® Block Filler 515001 or 2 coats Cal Pro 2000 Series Acrylic Flat 556XX▪ Ferrous Metal - Un-primed:1 coat Everlife Rust Inhibiting Metal Primer 521501 or 2 coats Cal Pro 2000 Series Acrylic Flat 556XX▪ Galvanized Metal:1 coat Everlife Rust Inhibiting Metal Primer, White 52161, Red 521501 or 2 coats Cal Pro 2000 Series Acrylic Flat 556XX▪ Wood:1 coat Prime Choice All Surface Acrylic Primer 503001 or 2 coats Cal Pro 2000 Series Acrylic Flat 556XX▪ Acoustical Tile:2 coats Cal Pro 2000 Series Acrylic Flat 556XXCal Pro 2000 Series Acrylic Latex Flat FinishPrecautions:Do not add solvents, oils or colors in oil, or mix with other paint types. Do not apply when air or surface temperature isbelow 50° F or when drying conditions are poor. Keep from freezing. Use adequate ventilation.Safety Information:Keep out of reach of children. Do not take internally. Close container after each use.*Specification data based on the pastel base: 55691**Information on EU VOC (Calculated differently from US Method): MAXIMUM VOC (As used) Based on EU CategoryA/a: 30 g/l Per EU Method Directive 2004/42/CE5/31/2012556XXProduct Specifications:Type: *Vinyl Acrylic LatexExposure:InteriorSpecular Gloss: 2 @ 60° ± 2Volume Solids: 31.1 % ±2Solids by Weight: 50.5 % ±2Vehicle: 58.3 % ±2Pigment: 41.7 % ±2Dry Film Thickness: 1.4 milsViscosity @ 77 °F:108KU ± 3Maximum VOC: **50 g/literFlash Pt °F: Non-combustibleThinner:WaterClean-Up: Soap & WaterAvailable Colors and Bases:WhiteMediumNeutralPastelDeepSuper Hide WhiteAvailable Package Sizes:Gallon5 Gallon(Weight Per Gallon: 11.6 lbs. ± .5 lb)Drying Times:To Touch: 1 hrs.To Handle: 4 hrs.To Recoat: 2 hrs.Surface Spread Rate:Smooth: 325-375s.f./gal.Porous: 250-300 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Brush -Synthetic, Nylon or PolyesterRoller -(@ 70-77 °F, 50% R.H.)3/8" Nap Synthetic FiberAirless Spray -.017 to .019 Tip<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141