Product Description:InteriorPRO 2000 LATEX CEILING FLAT WHITE is an anti-splatter, smooth flowing general purpose ceiling white formulatedwith the professional applicator in mind. It provides a high hiding smooth finish and uniform appearance with highproduction application.Recommended Use:Plaster, sheetrock, wallboard, concrete, wood, primed metal, acoustical surfaces, sand and texture finish ceiling.Application:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator tocontrol lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protectyourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on towww.epa.gov/lead.Surfaces to be painted must be free of dust, mildew, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap, andother surface contamination. Patch irregularities with vinyl patching paste or an appropriate patching compound. PRO2000 LATEX CEILING FLAT WHITE is self-priming over bare sheetrock, composition board, ceiling tile and concrete.New Plaster - Knife off all nibs and protrusions. Wipe with a clean damp cloth to remove loose particles. Do not sandnew plaster until it is primed.Wallboard, Sheetrock, Gypsum Board - Joint compound should be sanded smooth, but avoid abrading the paper.Ferrous Metal - Clean, then prime with Larcoloid ® Rust Inhibiting Metal PrimerWood - Seal knots and stains with Prime Choice Low Odor Oil Base Primer Sealer or Prime Choice 100% AcrylicUniversal Primer.Masonry Block - Apply one coat of Mason-Cote® Block Filler 3751 if a denser surface is desired.Architectural Specifications:▪ Plaster, Wallboard, Sheetrock:1 or 2 coats Pro 2000 Latex Ceiling Flat White 55500▪ Concrete, Non-Porous Masonry:1 or 2 coats Pro 2000 Latex Ceiling Flat White 55500▪ Porous Masonry and Block:1 coat ProPaint® Block Filler 515001 or 2 coats Pro 2000 Latex Ceiling Flat White 55500▪ Ferrous Metal - Un-primed:1 coat Larcoloid® Rust Inhibiting Metal Primer 211501 or 2 coats Pro 2000 Latex Ceiling Flat White 55500▪ Galvanized Metal:1 coat Larcoloid® Acrylic Latex Rust Inhibiting Metal Primer, White 51106, Gray 51108, Red 511071 or 2 coats Pro 2000 Latex Ceiling Flat White 55500▪ Wood:1 coat Prime Choice All Surface Acrylic Primer 503001 or 2 coats Pro 2000 Latex Ceiling Flat White 55500▪ Acoustical Tile:1 or 2 coats Pro 2000 Latex Ceiling Flat White 55500Precautions:Do not add solvents, oils or colors in oil, or mix with other paint types. Do not apply when air or surface temperature isbelow 50° F or when drying conditions are poor. Keep from freezing. Use adequate ventilation.Safety Information:Keep out of reach of children. Do not take internally. Close container after each use.5/31/2012Pro 2000® Latex Ceiling Flat White55500Product Specifications:Type: Vinyl Acrylic LatexExposure:InteriorSpecular Gloss: 2 @ 60° ± 2Volume Solids: 31.7 % ±2Solids by Weight: 51.4 % ±2Vehicle: 57.3 % ±2Pigment: 42.7 % ±2Dry Film Thickness: 1.4 milsViscosity @ 77 °F:107KU ± 3Maximum VOC: 100 g/literFlash Pt °F: Non-combustibleThinner:WaterClean-Up: Soap & WaterAvailable Colors and Bases:WhiteAvailable Package Sizes:Gallon5 Gallon(Weight Per Gallon: 11.8 lbs. ± .5 lb)Drying Times:To Touch: .5 hrs.To Handle: 4 hrs.To Recoat: 2 hrs.(@ 70-77 °F, 50% R.H.)Surface Spread Rate:Smooth: 350-400s.f./gal.Porous: 250-300 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Brush -Synthetic, Nylon or PolyesterRoller -3/8" Nap Synthetic FiberAirless Spray -.017 to .019 Tip<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141
Product Description:Ox-O-Flow is a high hiding flat oil base paint developed to seal, prime and finish most porous surfaces in one coat. Ox-O-Flow’s unique formulation allows application over calcimine, casein and other water soluble finishes without removalof the old finish. This quick drying, low odor paint flows on easily and is self-leveling.Recommended Use:Wood, plaster, drywall, primed metal, primed masonryApplication:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to controllead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect yourselfand your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on towww.epa.gov/lead.Surfaces to be painted must be free of dust, mildew, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap, andother surface contamination. Patch irregularities with vinyl patching paste or an appropriate patching compound.DATA/SPECIFICATIONS 9R0016Ox-O-Flow® Cal Coater70401Product Specifications:Type:Linseed OilExposure:InteriorSpecular Gloss: 2 @ 60° ± 2Volume Solids: 40.4 % ±2Solids by Weight: 67.1 % ±2Vehicle: 41.9 % ±2Pigment: 58.1 % ±2Dry Film Thickness: 2milsViscosity @ 77 °F: 87 KU ±5Maximum VOC: 475 g/literFlash Pt °F: 103Thinner: Mineral SpiritsClean Up: Mineral SpiritsPlaster, Veneer Plaster (Blueboard) - New plaster must be fully cured and should be wiped with a wet sponge toneutralize any “hot spots”. The moisture content should be below 15%. Full plaster requires a minimum of 30 days,skim coat plaster a minimum of 10 days to cure. Nibs should be knifed off before priming. Do not sand until after thesurface is primed with Dry Wall Primer or ASAP or 100% Acrylic Enamel Undercoat.Wallboard, Sheetrock, Gypsum Board - Joint compound should be sanded smooth, but avoid abrading the paper.Prime with Alkyd Primer-Sealer or Dry Wall Primer.Wood - Seal knots and stains with Wipe-Out ® , Wipe-Out Low Odor or Wipe-Out 100% Acrylic Stain BlockFerrous Metal - Clean, then prime with Larcoloid® Rust Inhibiting Metal Primer.Glossy Surfaces - Dull surface by sanding to insure adhesion of paint.Masonry Block - Apply one coat of Mason-Cote® Block Filler if a denser surface is desired or prime with ASAP, DryWall Primer or 100% Acrylic Enamel Undercoat.Architectural Specifications:OX-O-FLOW CAL COATER 70401▪ Plaster, Wallboard, Sheetrock:1 coat Alkyd Primer-Sealer 20200, AllWall® Primer 56600, ASAP® 50300 or 100% Acrylic Enamel Undercoat 546001 or 2 coats Ox-O-Flow Cal Coater 70401▪ Concrete, Non-Porous Masonry:1 coat AllWall Primer 56600, ASAP 50300 or 100% Acrylic Enamel Undercoat 546001 or 2 coats Ox-O-Flow Cal Coater 70401▪ Porous Masonry and Block:1 coat Mason-Cote® Block Filler 37511 or 2 coats Ox-O-Flow Cal Coater 70401▪ Ferrous Metal - Un-primed:1 coat Larcoloid® Rust Inhibiting Metal Primer 211501 or 2 coats Ox-O-Flow Cal Coater 70401▪ Galvanized Metal:1 coat Larcoloid Acrylic Latex Rust Inhibiting Metal Primer White 51106, Gray 51108 and Red 51101 or 2 coats Ox-O-Flow Cal Coater 70401▪ Wood:1 coat 100% Alkyd Enamel Undercoater 22200, Acrylic Enamel Undercoat or ASAP 503001 or 2 coats Ox-O-Flow Cal Coater 70401▪ Acoustical Tile:1 coat 100% Acrylic Enamel Undercoat 54600 or ASAP 503001 or 2 coats Ox-O-Flow Cal Coater 70401Precautions:Do not add water, oils or mix with other paints. Do not apply when air or surface temperature is below 50°F or whendrying conditions are poor. Do not use on unprimed plaster, masonry or galvanized surfaces. Ox-O-Flow Cal Coatershould not be used as a primer for latex paints since the weight of topcoats can cause the Ox-O-Flow to pull away fromthe substrate. Also, when Ox-O-Flow is used to coat calcimine, the water from a latex topcoat can seep through anddisrupt adhesion of the water soluble calcimine from its substrate.Safety Information:CAUTION! COMBUSTIBLE! Use only with adequate ventilation. Keep out of reach of children. Do not takeinternally. Close container after each use.Available Colors and Bases:WhiteAvailable Package Sizes:QuartGallon(Weight Per Gallon: 11.8 lbs. ± .5 lb)Drying Times:To Touch: 4-6 hrs.To Handle: 6 hrs.To Recoat: 16 hrs.(@ 70-77 °F, 50% R.H.)Surface Spread Rate:Smooth: 300-350s.f./gal.Porous: 225-275 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Brush -Natural Bristle, Nylon orPolyesterRoller -Short Nap Synthetic orNaturalAirless Spray -.011 to .013<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141