Product Description:INDUSTRIALInterior or ExteriorThis crystal clear multi-purpose acrylic sealer provides non-yellowing protection to a large variety of surfaces.LACRYLIC will seal both interior and exterior poured concrete wall and floor surfaces, to prevent both waterpenetration and surface dusting. This material can be topcoated with itself to provide an abrasion resistant clearcoating, or topcoated with pigmented alkyd or urethane. Flagstone, terra cotta and slate can be sealed and finishedwith two coats of LACRYLIC. LACRYLIC seals common red brick and prevents oxide bleed-through on finish coats ofpaint. LACRYLIC will also seal old unfinished stucco to prevent loss of adhesion of latex finish coats. LACRYLIC isan excellent sacraficial anti-graffiti coating.Recommended Use:Masonry, Stucco, Flagstone, Brick, Concrete FloorsApplication:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator tocontrol lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protectyourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on towww.epa.gov/lead.Remove all surface contaminants including grease, oil, rust, stains, dirt, dust, wax and mortar splatter. New concretemust cure for a minimum of 28 days prior to application of Lacrylic. Lacrylic is supplied at proper applicationconsistency and generally requires no thinning. Material can be applied successfully by brush, roller or airless spray.Apply full-body working the material into the pores of the surface. Clean up sealer spatters and equipment immediatelyafter use with #2308 thinner.Architectural Specifications:▪ Concrete Floors2 coats Lacrylic Clear Anti-graffiti / Waterproofing Coating▪ Patio Flagstone, Terra Cotta2 coats Lacrylic Clear Anti-graffiti / Waterproofing Coating▪ Brick – Painted: Common, Red Clay Type (or soot stained)1 coat Lacrylic Clear Anti-graffiti / Waterproofing Coating2 coats <strong>California</strong>® Acrylic Latex▪ Wood (& Plywood): Low Gloss Stain Proof Finish2 coats Lacrylic Clear Anti-graffiti / Waterproofing CoatingLacrylic® Clear Anti-Graffiti / Waterproofing CoatingPrecautions:Do not mix with water or other type paints. Do not apply below 40°F or apply to a damp surface. Not recommended asa sealer on glazed, quarry or other ceramic type tiles. Steel troweled concrete must be acid etched prior to applicationof Lacrylic to ensure adhesion to the concrete. Steel troweled smooth concrete with a curing membrane or hardenermay require abrasion to obtain proper adhesion.Safety Information:DANGER! HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE. HARMFUL IF INHALED. MAY AFFECT THEBRAIN OR NERVOUS SYSTEM, CAUSING DIZZINESS, HEADACHE OR NAUSEA. CAUSES NOSE, THROAT, EYEAND SKIN IRRITATION. CONTAINS PETROLEUM DISTILLATEKeep away from heat and flame. To avoid breathing vapors or spray mist, open windows and doors or use othermeans to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness,increase fresh air or wear respiratory protection (NIOSH/MSHA TC 23C or equivalent) or leave the area.Do not transfer contents to unlabeled bottles or other containers.Close container after each use. Avoid contact with skin.FIRST AID: If swallowed, CALL A PHYSICIAN IMMEDIATELY. Never give anything by mouth to an unconsciousperson.USE WITH ADEQUATE VENTILATION.NOTICE: Reports have associated repeated and prolonged occupational overexposure to solvents with permanentbrain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may beharmful or fatal.FOR INDUSTRY USE ONLYKEEP OUT OF REACH OF CHILDREN5/31/20127110Product Specifications:Type: Solvent AcrylicExposure: Interior or ExteriorSpecular Gloss:NA@ 60° ±Volume Solids: 14.9 % ±2Solids by Weight: 19.1 % ±2Vehicle: 100 % ±2Pigment: % ±2Dry Film Thickness: 1.2 milsViscosity @ 77 °F: NAKU ±Maximum VOC: 600 g/literFlash Pt °F: 108Thinner: 2308Clean-Up:XylolAvailable Colors and Bases:CleartoneAvailable Package Sizes:Gallon5 Gallon(Weight Per Gallon: 7.8 lbs. ± .5 lb)Drying Times:To Touch: .5 hrs.To Handle: 1 hrs.To Recoat: 1 hrs.Surface Spread Rate:Smooth: 150-175s.f./gal.Porous: 100-125 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Brush -Natural BristleRoller -(@ 70-77 °F, 50% R.H.)3/8" Nap Synthetic FiberAirless Spray -.011 to .013 Tip<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141
Product Description:Grid-Stripe is a long lasting, highly visible athletic field marking paint designed to put bright, sharp lines on grasssurfaces. This non-toxic material will not chalk, rub off on athletic jerseys or wash away during rainy periods. Grid-Stripe is LIME FREE so that players are protected against burns and eye injuries caused by contact with limemarkings on athletic fields.Recommended Use:Football, soccer, lacrosse, field hockey, baseball and other athletic fields.Application:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator tocontrol lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protectyourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on towww.epa.gov/lead.Grass should be comparatively short before application of Grid-Stripe. Application should not be attempted if surfacesare wet from dew or rain to avoid blurring of athletic markings. Grid Stripe can be applied by any gravity fed, spray orroller type line marking machine. Initial application usually requires two coats to achieve bright, sharp lines. First coatshould be thinned about 10% with water. Second coat can be applied in approximately one hour. Relining orpatchings should be done as necessary to maintain proper athletic field marking. Normal life expectancy is about twoweeks when grass is cut on a regular basis.Architectural Specifications:NAINDUSTRIALExteriorPrecautions:Material should not be thinned with solvent. Grid-Stripe should not be applied below 50°F or when rain is imminent.Safety Information:Keep out of reach of children. Do not take internally. Close container after each use.5/31/2012Grid-Stripe® Athletic Field Marking1001Product Specifications:Type: Vinyl Acrylic LatexExposure:ExteriorSpecular Gloss: 2 @ 60° ± 2Volume Solids: 33.0 % ±2Solids by Weight: 54.0 % ±2Vehicle: 53.0 % ±2Pigment: 47.0 % ±2Dry Film Thickness: milsViscosity @ 77 °F:100KU ± 5Maximum VOC: 100 g/literFlash Pt °F: Non-combustibleThinner:WaterClean-Up: Soap & WaterAvailable Colors and Bases:WhiteAvailable Package Sizes:Gallon5 Gallon(Weight Per Gallon: 12.2 lbs. ± .5 lb)Drying Times:To Touch: .5 hrs.To Handle: 4 hrs.To Recoat: 1-2 hrs.(@ 70-77 °F, 50% R.H.)Surface Spread Rate:Smooth:Porous:s.f./gal.s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Spray -Marking MachineRoller -Marking Machine<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141