Product Description:flawless ELEMENTS Zero VOC Interior Semi-Gloss is an environmentally preferred, premium quality interior paintthat provides flawless application and exceptional durability with essentially no odor during and after painting. Thisproduct is self-priming over many new and previously painted surfaces. Specific primers are recommended for manynew wood surfaces. Rooms and offices painted with flawless ELEMENTS Zero VOC can be occupied right awaywithout a compromise to healthy indoor air quality. With Microban® antimicrobial protection, flawless ELEMENTSprovides an added level of mildew resistance not found in other Zero VOC paints. For more information visitwww.microban.com.Recommended Use:Plaster, sheetrock, wallboard, concrete, masonry block, wood, primed metal, galvanized metal, acoustical surfaces.Application:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE.Wear a NIOSH-approved respirator to control lead exposure. Carefully clean up with a wetmop or HEPA vacuum. Before you start, find out how to protect yourself and your family by contacting the U.S.EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on to www.epa.gov/lead.Surfaces to be painted must be free of dust, mildew, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap, andother surface contamination. Patch irregularities with vinyl patching paste or an appropriate patching compound.flawless ELEMENTS Zero VOC Interior Semi-gloss 100% Acrylic latex enamel with Microban is self-priming over baresheetrock, composition board, ceiling tile and concrete.Plaster, Veneer Plaster (Blueboard) - New plaster must be fully cured and should be wiped with a wet sponge toneutralize any "hot spots". The moisture content should be below 15%. Full plaster requires a minimum of 30 days,skim coat plaster a minimum of 10 days to cure. Nibs should be knifed before painting. Do not sand until after thesurface is painted.Ferrous Metal - Clean, then prime with Rust Stop® Rust Inhibiting Metal PrimerNew Wood - Knots and stains should be sealed with Prime Choice® Oil Based Stain-blocking Primer #20700 or PrimeChoice Universal Latex Stain-blocking Primer #50600 to avoid staining. All wood should then be primed with <strong>California</strong>Prime Choice Alkyd Primer-sealer #20200 or Prime Choice Latex All Surface Primer #50300.Masonry Block - Apply one coat of Mason-Cote® Block Filler 3751 if a denser surface is desired.Architectural Specifications:▪ Plaster, Wallboard, Sheetrock:1 coat flawless ELEMENTS Zero VOC Interior 100% Acrylic Latex Primer-Sealer 74600 or2 coats flawless ELEMENTS Zero VOC Interior Semi-gloss 100% Acrylic Latex Enamel with Microban 763XX▪ Concrete, Non-Porous Masonry:2 coats flawless ELEMENTS Zero VOC Interior Semi-gloss 100% Acrylic Latex Enamel with Microban 763XX▪ Porous Masonry and Block:1 coat Mason-Cote® Block Filler 37511 or 2 coats flawless ELEMENTS Zero VOC Interior Semi-gloss 100% Acrylic Latex Enamel with Microban 763XX▪ Ferrous Metal - Un-primed:1 coat Rust Stop® Rust Inhibiting Metal Primer1 or 2 coats flawless ELEMENTS Zero VOC Interior Semi-gloss 100% Acrylic Latex Enamel with Microban 763XX▪ Ferrous Metal -Primed, Galvanized Metal:2 coats flawless ELEMENTS Zero VOC Interior Semi-gloss 100% Acrylic Latex Enamel with Microban 763XX▪ Wood:1 coat flawless ELEMENTS Zero VOC Interior 100% Acrylic Latex Primer-Sealer 746001 or 2 coats flawless ELEMENTS Zero VOC Interior Semi-gloss 100% Acrylic Latex Enamel with Microban 763XX▪ Acoustical Tile:2 coats flawless ELEMENTS Zero VOC Interior Semi-gloss 100% Acrylic Latex Enamel with Microban 763XXPrecautions:Do not add solvents, oils or colors in oil, or mix with other paint types. Do not apply when air or surface temperature isbelow 50° F or when drying conditions are poor. Keep from freezing. Use adequate ventilation.Safety Information:Keep out of reach of children. Do not take internally. Close container after each use.* Specifications shown above are for 76391SELF-PRIMINGInterior5/31/2012flawless ELEMENTS Zero VOC Semi-Gloss100% Acrylic Latex Enamel with Microban® 763XX*Product Specifications:Type: 100% Acrylic LatexExposure:InteriorSpecular Gloss: 37@ 60° ± 5Volume Solids: 39.5 % ±2Solids by Weight: 53.0 % ±2Vehicle: 71.9 % ±2Pigment: 28.1 % ±2Dry Film Thickness: 2 milsViscosity @ 77 °F: 95KU ± 5Maximum VOC: Calc. 0 g/literFlash Pt °F: Non-combustibleThinner:WaterClean-Up: Soap & WaterAvailable Colors and Bases:WhiteMediumNeutralPastelDeepAvailable Package Sizes:Quart Gallon 5 Gallon(Weight Per Gallon: 10.8 lbs. ± .5 lb)Drying Times:To Touch: 2 hrs.To Handle: 24 hrs.To Recoat: 4 hrs.Surface Spread Rate:Smooth: 300-350s.f./gal.Porous: 250-300 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Brush -Synthetic, Nylon or PolyesterRoller -(@ 70-77 °F, 50% R.H.)3/8" Nap Synthetic FiberAirless Spray -.017 to .019 Tip<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141
Product Description:Interior or ExteriorThis is the finest quality, all-purpose alkyd semi-gloss enamel available. This hard, durable finish flows on easily andlevels to a beautiful smooth lustrous finish. Used as is or tinted according to directions, this hard, durable nonindustrialfinish will help prevent rusting of ferrous metal substrates. Alkyd paints oxidize with age so light colors willeventually show yellowing, expecially in poorly lighted areas.Recommended Use:Metal Doors ▪ Handrails ▪ Household Tools ▪ Garden Equipment ▪ Steel ShelvingApplication:WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY INCHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator tocontrol lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protectyourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on towww.epa.gov/leadSurfaces to be painted must be free of dust, mildew, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap, andother surface contamination.Stir thoroughly before using to insure proper dispersion. This product is of proper consistency as packaged to beapplied without thinning under normal environmental and application conditions.This product can be tinted with Universal Colorants but the amount of colorant should not exceed the amountrecommended for the tint base used.Apply by brush or roller using long strokes. Two coats are generally required for deep and ultra deep colors or whenpainting over a contrasting color. Apply paint on a small area, allow it to dry and approve for accuracy beforecompleting the job.Previously painted surfaces in good condition do not require a primer. One coat of Fres~Coat Alkyd Enamel is usuallysufficient while two coats will provide more durability. On new or previously painted metal surfaces where rusting is aproblem, remove all traces of rust by sandpaper, scraper or mechanical means and prime with a rust-inhibitive primersuch as Larcoloid® Inhibiting Metal Primer and finish with 1 or 2 coats of Fres~Coat Alkyd Enamel.Fres~Coat Alkyd Semi-GlossRust Preventative for Metal Substrates5/31/2012210XXProduct Specifications:Type:AlkydExposure: Interior or ExteriorSpecular Gloss: 60@ 60° ± 5Volume Solids: 56.5 % ±2Solids by Weight: 74.9 % ±2Vehicle: 57.7 % ±2Pigment: 42.8 % ±2Dry Film Thickness: 2.0 milsViscosity @ 77 °F: 80KU ± 5Maximum VOC: 400 g/literFlash Pt °F: 103Thinner: Mineral SpiritsClean-Up: Mineral SpiritsAvailable Colors and Bases:WhiteMediumUltra DeepPastelDeepNeutralAvailable Package Sizes:QuartGallonFerrous Metal - Clean, then prime with Larcoloid Rust Inhibiting Metal Primer.Glossy Surfaces - Dull surface by sanding to insure adhesion of paint.Architectural Specifications:▪ Ferrous Metal - Un-primed:1 coat Larcoloid Rust Inhibiting Metal Primer 211501 or 2 coats Fres~Coat Alkyd Semi-Gloss 210XX*▪ Galvanized Metal:1 coat Larcoloid Acrylic Latex Rust Inhibiting Metal Primer White 51106, Gray 51108 and Red 511071 or 2 coats Fres~Coat Alkyd Semi-Gloss 210XX*Precautions:Do not add water, oils or mix with other paints. Do not apply when air or surface temperature is below 50°F or whendrying conditions are poor. Do not use on unprimed galvanized surfaces.Safety Information:CAUTION! COMBUSTIBLE! Use only with adequate ventilation. Keep out of reach of children. Do not takeinternally. Close container after each use.*Note: Maximum hardness is achieved in 3-4 weeks.(Weight Per Gallon: 11.1 lbs. ± .5 lb)Drying Times:To Touch: 4-6 hrs.To Handle: 16 hrs.To Recoat: 24 hrs.(@ 70-77 °F, 50% R.H.)Surface Spread Rate:Smooth: 400-500 s.f./gal.Porous: 250-300 s.f./gal.(Spray Application is 50% of above)Tools and Equipment:Brush -Synthetic, Nylon or PolyesterRoller -3/8" Nap Synthetic FiberAirless Spray -.017 to .019 Tip<strong>California</strong> <strong>Paints</strong> ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.californiapaints.com ▪ 800-225-1141