CORTEX- VMS Configuration manual - Qvis Security

More documents

Recommendations

Info

• Video compression – compression level of the video sent by the cameras. The label underneath shows the current minimal, maximal and average compression level of the selected cameras. • Audio compression – compression level of the audio sent by the cameras. The label underneath shows the current minimal, maximal and average compression level of the selected cameras. The above parameters can be altered in two ways: • Relative – for each camera – change a setting to a lower level (by clicking the “-“ button) or higher level (by clicking the “+” button) than the current settings. To change a parameter relatively, select the Relative option next to it. • Absolute – for all cameras. Setting the Absolute option next to a parameter allows to set the same parameter value for all selected cameras. The Record video and Record audio parameters can only be changed absolutely. If these parameters are not set, the selected cameras will not have this option changed (recording will stay switched on the cameras which had it switched on previously and the cameras which had it switched off previously will stay switched off). Clicking the OK button will change the parameters of the selected cameras and go back to the Recording settings window. After closing this window, the calculation of bit rate, storage space and estimated recording time will begin again with the new settings. This process can take up to a few minutes, depending on the number of cameras in the system. Clicking the Cancel button will close the window without changing any recording parameters of the cameras. 2.5.12 IO devices This window is used for configuration of IO devices in the system. To show this window, click the IO devices button in the Settings window. The IO device list lists all IO devices available in the system. To add a new IO device, click on the Add button on the element management panel and fill out fileds describing the IO device. Next, click the Save button. The new added IO device will appear in the IO device list. To edit an IO device, select its name on the IO device list by clicking on it, click the Edit button on the element management panel, change data in the edit fields describing the IO device and then click the Save button. The edit fields in this window are: • Device type – type of the IO device. • Device name – device name. • Device IP address – IP address of the IO device. • Device port – port number of the IO device. • Device login – login name of the user having administrative privileges on the IO device (it is stored in the IO device configuration). • Device password – password for the user identified by the login in the Device login field (it is stored in the IO device configuration). Cortex IP Video Management System Configuration manual 28
IO device list 2.5.13 Monitors This window is used for management of monitor servers. To show this window, click the Monitors button in the Settings window. The Monitor list contains all monitor servers. Clicking on an element causes its parameters to be displayed in the edit fields (Name, IP address, Display index). To add a new monitor, click the Add button on the element management panel, fill out the edit fields and then click the Save button. The newly added monitor will appear in the Monitor list. The Display index is a zero-based index of the display on the physical monitor server machine. One monitor server can have several independent displays. To use all of them, the physical machine has to have multiple instances of the monitor server software installed and there have to be multiple entries in the Monitor list with all display indices. Cortex IP Video Management System Configuration manual 29
Page 1 and 2: Cortex IP Video Management System C
Page 3 and 4: Introduction This document covers t
Page 5 and 6: 5. System configuration For a simpl
Page 7 and 8: Clicking the Next step button will
Page 9 and 10: This window is used to change the a
Page 11 and 12: • The Server field should have th
Page 13 and 14: 2.4.3 Support This function is cove
Page 15 and 16: Current screen settings are shown i
Page 17 and 18: To change settings of a network ada
Page 19 and 20: • Internal path - the internal st
Page 21 and 22: • Device login - login name of th
Page 23 and 24: Clicking the Cancel button will clo
Page 25 and 26: The parameter fields in this window
Page 27: Clicking the Recalculate button rec
Page 31: To add a device item, click the Add

CORTEX- VMS Configuration manual - Qvis Security

Create successful ePaper yourself

Delete template?

Save as template?