IQ plus 810 - Rice Lake Weighing Systems

More documents

Recommendations

Info

CALIBRATECONFIGURATION SET ANALOG FORMAT SETPOINTS SERIAL DIGITAL IN ANALOG OUT BAR GRAPH(CALIBRATION)CALIBRT(CHANNEL 1 CALIBRATION)CHAN 1(CHANNEL 2 CALIBRATION)CHAN 2(CHANNEL 3 CALIBRATION)CHAN 3(CHANNEL 4 CALIBRATION)CHAN 4IDENTICAL PROCEDURE ASFOUND UNDER CHAN 1IDENTICAL PROCEDURE ASFOUND UNDER CHAN 1IDENTICAL PROCEDURE ASFOUND UNDER CHAN 1➡➡➡(WEIGHT CALIBRATION)WEIGHT(VOLTS CALIBRATION)VOLTSCalibrated at factory. Do NOTchange calibration values underthe "VOLTS" menu.(ZERO WEIGHT CAL)W ZERO(WEIGHT VALUE CAL)W VAL(SPAN WEIGHT CAL)W SPAN(ZERO VOLTS CAL)V ZERO(WEIGHT VALUE CAL)V VAL(SPAN VOLTS CAL)V SPAN(CLEAR SCALE ANDPUSHENTER)(ENTER TEST WEIGHTVALUE)XXXXX(PLACE TEST WEIGHTON SCALE AND PUSHENTER)(ENTER 0 VOLTS ORPUSH ENTER TOCALCULATE)(ENTER CAL WEIGHTVALUE)XXXXX, PUSH ENTER(ENTER SPAN VOLTSOR PUSH ENTER TOCALCULATE)Detailed directions for calibration procedures are found in Section 8, Calibration.6 - 17
6.1 MENU DESCRIPTIONSCONFIGURATION MENU DESCRIPTIONS (Defaults in Bold Type with √)NAME DESCRIPTION CHOICESGRADS 1Graduations. This parameter specifies the number of full scalegraduations. The value entered should be consistent with legalrequirements and environmental limits on the useful system resolution.Enter value with numerical keyboard then exit upward to enterthe new value.This parameter, and the first three parameters (DSP DIV, DEC PNT,and UNITS) under Primary Scale in the FORMAT 1st level menu,define the scale capacity. For example, if GRADS = 10,000, DSP DIV =5, DEC PNT = 88888.88, and UNITS = LB, then the scale capacity is500.00 LB in .05 increments0 to 100,000Default = 10,000 √GRADS 2 Same as GRADS 1 for the optional input channels 2-4.GRADS 3GRADS 4Same as GRADS 1ZTRKBNDZRANGEMOTBANDOVRLOADZero Track Band. Automatically zeroes the scale when it is within therange of selected values, as long as the input is within the ZRANGE,and the scale is in standstill. Selections are ± DD. Maximum legalvalue varies depending on local regulations.Zero Range. Selects the range within which the scale may bezeroed. The 1.9% selection is ±1.9% around the calibrated zeropoint, for a total range of 3.8%. Indicator must be in standstill to zerothe scale. Use 1.9% for Legal-For-Trade applications.Motion Band. Sets the level at which scale motion is detected bycomparing the present display update with the previous update. Ifmotion is not detected for 1 second or more, the standstill symbollights and the scale can process a Print command. Maximumlegal value varies depending on local regulations.Overload. Determines the point at which the display blanks and anerror message is displayed, indicating an out-of-range condition.Maximum legal value varies depending on local regulations.OFF√ 0.5 D1 D 3 D1.9%√ 100%1 D√3 D5 D10 DFS FS + 2%√FS + 1D FS + 9DPWR UPPower Up Mode. In the GO mode, the scale goes into operationimmediately after a brief power up display test. In the DELAY mode,the scale does a power up display test, then must warm up (WARMUP and the standstill symbol are displayed) with no motion detectedfor 30 seconds before going into operation. If motion is detectedwithin that period, the 30-second sequence restarts. The delay isused where local regulations require a warm-up period.GO√DELAY200TARE200 ID/Tare Truck In/Out Mode. If enabled by selecting one of the sixTruck In/Out modes, the indicator shifts from the Normal <strong>Weighing</strong>Mode into the truck mode selected. See Section 3.4.MODE 1: Auto Clear ID, Keyed Tares, Value SwappingMODE 2: Auto Clear ID, No Keyed Tares, Value SwappingMODE 3: Stored ID, Keyed Tares, Value SwappingOFF√MODE 1MODE 2MODE 3MODE 4MODE 5MODE 66 - 18
Page 1 and 2: IQ plus810®MADE IN USAIQ plus 810D
Page 3 and 4: SECTIONTABLE OF CONTENTSPAGE1. INTR
Page 5 and 6: Application Specialists at Rice Lak
Page 7 and 8: 1 2 34 5 67 8 90 ENTERThese keys ar
Page 9 and 10: SETPOINTThe SETPOINT key is used to
Page 11 and 12: 3.4 TRUCK IN/OUT MODEThe indicator
Page 13 and 14: 4. INSTALLATION AND WIRINGAC LINE C
Page 15 and 16: Power Supply/Display BoardBatteryJ2
Page 17 and 18: SERIAL COMM. WIRINGJ7-1 1-6, PRINTJ
Page 19 and 20: MAIN BOARD TO DISPLAY/POWER SUPPLY
Page 21 and 22: 5. SERIAL COMMUNICATION PORTSThe IQ
Page 23 and 24: Terminal block J7 on the main board
Page 25 and 26: CONFIGURATION SET ANALOG FORMAT SET
Page 27 and 28: SET ANALOG FORMAT SETPOINTS SERIAL
Page 29 and 30: FORMAT SETPOINTS SERIAL DIGITAL IN
Page 31 and 32: SETPOINTS SERIALANALOG OUT BAR GRAP
Page 33 and 34: SETPOINTSSERIALDIGITAL IN ANALOG OU
Page 35 and 36: SERIALDIGITAL IN ANALOG OUT BAR GRA
Page 37 and 38: DIGITAL IN ANALOG OUT BAR GRAPH CAL
Page 39: BAR GRAPH CALIBRATE CONFIGURATION S
Page 43 and 44: 6.1 MENU DESCRIPTIONS (CONTINUED)SE
Page 45 and 46: 6.1 MENU DESCRIPTIONS (CONTINUED)FO
Page 51 and 52: 6.1 MENU DESCRIPTIONS (CONTINUED)DI
Page 53 and 54: 6.1 MENU DESCRIPTIONS (CONTINUED)BA
Page 55 and 56: 7. SETPOINT AND BATCH PROCESSINGThe
Page 57 and 58: BATCH STEP SETPOINTSThe system has
Page 59 and 60: THE FOLLOWING CONTINUOUS SETPOINT T
Page 61 and 62: SETPOINT WORKSHEET--CONTINUOUS RUNN
Page 63 and 64: BATCHING WORKSHEETSP 1 SP 2 SP 3 SP
Page 65 and 66: 8. CALIBRATIONCALIBRATECONFIGURATIO
Page 67 and 68: 9. REMOTE OPERATION VIA EDP SERIAL
Page 69 and 70: SET ANALOG SUB-MENUCHANSPULSINRESOL
Page 71 and 72: CALIBRATE SUB-MENUCH1.VZERONumberCH
Page 73 and 74: IQ plus 810MADE IN USA10.1 APPLICAT
Page 75 and 76: IQ plus 810MADE IN USA10.3 ACCUMULA
Page 77 and 78: IQ plus 810MADE IN USA10.5 BAR GRAP
Page 79 and 80: IQ plus 810MADE IN USA10.6 EXPANSIO
Page 81 and 82: IQ plus 810MADE IN USA10.8 AUXILIAR
Page 83 and 84: IQ plus 810MADE IN USA10.10 MULTIPL
Page 85 and 86: -IQ plus 810MADE IN USAOPTIONAL FEA
Page 87 and 88: IQ plus 810MADE IN USA10.12 SINGLE
Page 89 and 90: IQ plus 810MADE IN USA10.13 SETPOIN
Page 91 and 92:
IQ plus 810MADE IN USAOPTIONAL FEAT
Page 93 and 94:
Page 95 and 96:
IQ plus 810MADE IN USA10.18 WALL MO
Page 97 and 98:
Page 99 and 100:
11. BOARD DIAGRAMSSW1J8U2J2U1U3J7U2
Page 101 and 102:
OPERATOR INTERFACEDisplayAdditional
Page 103 and 104:
14. APPENDIXSec. Description Page14
Page 105 and 106:
CONVERSION FACTORSTO CONVERT INTO M
Page 107 and 108:
CONVERSION FACTORSTO CONVERT INTO M
Page 109 and 110:
14.5 ASCII CHARACTERS WITH DECIMAL
Page 111 and 112:
To understand how these formats pro
Page 113 and 114:
14.8 REPLACEMENT PARTS LISTService/
Page 115 and 116:
QUESTIONS ABOUT THE HO LINE TM8 0 C
Page 117 and 118:
IQ plus 810MADE IN USAImportant Ins
show all

IQ plus 810 - Rice Lake Weighing Systems

Create successful ePaper yourself

Delete template?

Save as template?