Prestige Trimax Solo 60175250399 install manual - Coastal Winair

More documents

Recommendations

Info

Combustion Air VentingRemoval of an Existing Boiler from aCommon Vent SystemBEST PRACTICEWhen an existing boiler is removed from acommon venting system, the common ventingsystem is likely to be too large for properventing of the remaining appliances. At thetime of removal of an existing boiler, the followingsteps shall be followed with eachappliance remaining connected to the commonventing system placed in operation,while the other appliances remaining connectedto the common venting system are notin operation.1. Seal any unused openings in the commonventing system.2. Visually inspect the venting system forproper size and horizontal pitch and determinethere is no blockage or restriction,leakage, corrosion and other deficiencieswhich could cause an unsafe condition.3. Insofar as is practical, close all buildingdoors and windows and all doors betweenthe space in which the appliances remainingconnected to the common venting systemare located and other spaces of thebuilding. Turn on clothes dryers and anyappliance not connected to the commonventing system. Turn on any exhaust fans,such as range hoods and bathroomexhausts, so they will operate at maximumspeed. Do not operate a summer exhaustfan. Close fireplace dampers.4. Place in operation the appliance beinginspected. Follow the lighting instructions.Adjust thermostat so appliance will operatecontinuously.5. Test for spillage at the draft hood reliefopening after 5 minutes of main burneroperation. Use the flame of a match or candle,or smoke from a cigarette, cigar or pipe.6. After it has been determined that eachappliance remaining connected to the commonventing system properly vents whentested as outlined above, return doors, windows,exhaust fans, fireplace dampers, andany other gas-burning appliance to theirprevious condition of use.7. Any improper operation of the commonventing system should be corrected so theinstallation conforms with the NationalFuel Gas Code, ANSI Z223.1/NFPA 54and/or CAN/CGA B149, Installation codes.When resizing any portion of the commonventing system, the common venting systemshould be resized to approach the minimumsize as determined using the appropriatetables in Part II of the National FuelGas Code ANSI Z223.1/NFPA 54 and/orCAN/CGA B149, Installation codes.DANGERDo not install the PRESTIGE Solo into acommon vent with other gas or oil appliances.This may cause flue gas spillage orappliance malfunction, resulting in possiblesevere personal injury, death or substantialproperty damage.10
Combustion Air VentingCommonwealth of Massachusetts Installations OnlyFor direct-vent appliances, mechanicalventheating appliances or domestic hotwater equipment, where the bottom of thevent terminal and the air intake is installedbelow four feet above grade the followingrequirements must be satisfied:1. If there is not one already present, oneach floor level where there are bedroom(s),a carbon monoxide detectorand alarm shall be placed in the livingarea outside the bedroom(s). The carbonmonoxide detector shall complywith NFPA 720 (2005 Edition).2. A carbon monoxide detector shall alsobe located in the room that houses theappliance or equipment and shall:a. Be powered by the same electrical circuitas the appliance or equipment suchthat only one service switch servicesboth the appliance and the carbonmonoxide detector;b. Have battery back-up power;c. Meet ANSI/UL 2034 Standards andcomply with NFPA 720 (2005 Edition);andd. Have been approved and listed by theNationally Recognized TestingLaboratory as recognized under 527CMR.3. A Product-approved vent terminal mustbe used, and if applicable, a Productapprovedair intake must be used.Installation shall be in strict compliancewith the manufacturer’s instructions. Acopy of the installation instructionsshall remain with the appliance orequipment at the completion of theinstallation.4. A metal or plastic identification plateshall be mounted at the exterior of thebuilding, four feet directly above thelocation of vent terminal. The plateshall be of sufficient size to be easilyread from a distance of eight feet away,and read “Gas Vent Directly Below”.NOTICEInstaller must provide tag identificationplate and ensure the lettering meets coderequirements.For direct-vent appliances, mechanicalventheating appliances or domestic hotwater equipment, where the bottom of thevent terminal and the air intake are installedabove four feet above grade the followingrequirements must be satisfied:1. If there is not one already present, oneach floor level where there are bedroom(s),a carbon monoxide detectorand alarm shall be placed in the livingarea outside the bedroom(s). The carbonmonoxide detector shall complywith NFPA 720 (2005 Edition).2. A carbon monoxide detector shall:a. Be located in the room that houses theappliances or equipment;b. Be either hard wired or battery poweredor both; andc. Shall comply with NFPA 720 (2005Edition)3. A Product-approved vent terminal mustbe used, and if applicable, a Productapprovedair intake must be used.Installation shall be in strict compliancewith the manufacturer’s instructions. Acopy of the installation instructionsshall remain with the appliance orequipment at the completion of theinstallation.11
Page 1 and 2: prestigeSolo 60Solo 175Solo 250Solo
Page 3 and 4: Table of ContentsBoiler System Pipi
Page 5 and 6: Table of ContentsUse of Antifreeze
Page 7 and 8: Product & Safety InformationDefinit
Page 9 and 10: Pre-Installation ItemsSECTION I - P
Page 11 and 12: Combustion Air VentingSECTION II -
Page 13 and 14: Combustion Air VentingMethods of Ac
Page 15: Combustion Air VentingCombination o
Page 19 and 20: Unit PreparationsPRESTIGE Solo 60/1
Page 21 and 22: Boiler PipingPressure Relief Valve(
Page 23 and 24: Boiler PipingConnect the expansion
Page 25 and 26: Boiler PipingFig. 7: Near Boiler Pi
Page 27 and 28: Boiler PipingNote: Reference Fig. 2
Page 29 and 30: Boiler PipingFig. 13: Multiple PRES
Page 31 and 32: Installing Vent/Combustion Air & Co
Page 33 and 34: Gas PipingNATURAL GASPipe Sizing -
Page 35 and 36: Gas PipingGas ValveGasketOrificeGas
Page 37 and 38: Internal WiringTriMaxDisplayModuleP
Page 39 and 40: External Wiringcall. This circulato
Page 41 and 42: External WiringCAUTIONLocate the sy
Page 43 and 44: External WiringFig. 21: Multiple Zo
Page 45 and 46: External WiringNote: Reference Fig.
Page 48 and 49: abc de f bbb babc de f bbabc deabc
Page 50 and 51: TriMax OperationStatus Line Message
Page 52 and 53: TriMax OperationEZ SetupNavigation:
Page 54 and 55: TriMax OperationDomestic Hot Water
Page 56 and 57: TriMax OperationCH/DHW OperationNav
Page 58 and 59: abc de f bbb babc de f bbabc deabc
Page 60 and 61: TriMax OperationManual Reset Hard L
Page 62 and 63: Start-Up PreparationSECTION X - Sta
Page 64 and 65: Start-Up PreparationCheck For Gas L
Page 66 and 67:
Start-Up ProcedurescccCheck Vent Pi
Page 68 and 69:
Start-Up ProceduresFOR YOUR SAFETY
Page 70 and 71:
External Modulating ControlSECTION
Page 72 and 73:
Check-Out ProceduresSECTION XIV- Ch
Page 74 and 75:
Maintenance SchedulesSECTION XVI -
Page 76 and 77:
Maintenance ProceduresClean Condens
Page 78 and 79:
Maintenance ProceduresCheck Control
Page 80 and 81:
Maintenance Procedures15. Once the
Page 82 and 83:
Replacement Parts65841243Fig. 34: P
Page 84 and 85:
Replacement Parts249351610487Fig. 3
Page 86 and 87:
Replacement Parts2349516410Fig. 38:
Page 88 and 89:
Replacement Parts73847109261Fig. 40
Page 90 and 91:
Product Specifications15 3/8” [39
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Product SpecificationsBoilerModelFu
Page 98 and 99:
Product SpecificationsGraph 4: Pres
Page 100:
Additional quality water heating eq
show all

Prestige Trimax Solo 60175250399 install manual - Coastal Winair

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?