KMD-201AA KMD-201AWA - Hoshizaki

More documents

Recommendations

Info

f) LED Lights and Audible Alarm SafetiesThe control board includes LED indicator lights, audible alarm safeties, and an output testfeature. The "POWER OK" LED indicates control voltage and will remain on unless a controlvoltage problem occurs. The “POWER OK” LED flashes continuously when the bin is fulland DV energizes for a maximum of 5 minutes to drain the water tank.At startup, a 5 second delay occurs to stabilize the circuit. LEDs 4 through 8 energize andsequence from initial startup as listed in the table below. Note that the order of the LEDsfrom the outer edge of the board is 5, 6, 8, 9, 4, 7. For more information, see "2.SEQUENCE OF OPERATION".HWVHWV, HGV,Comp5, 7 (and9 at refill)Comp, PM, FMS(FWV at refill)DV- drain valve; FMS-self-contained fan motor;WRV-water regulating valve;11
[c] CONTROLS AND ADJUSTMENTSa) Default Dip Switch SettingsThe dip switch is factory-adjusted to the following positions:KMD-201AA(50Hz)KMD-201AA(60Hz)KMD-201AWA(50Hz)KMD-201AWA(60Hz)KMD-201AA(50Hz)KMD-201AA(60Hz)KMD-201AWA(50Hz)KMD-201AWA(60Hz)Do not adjust the S2 dip switch. These must be left in the factory default position, or the unitwill not operate properly.b) Harvest Timer (S1 dip switch 1 & 2)Used for adjustment of the harvest timer. The harvest timer starts counting when thethermistor reads a certain temperature at the evaporator outlet.12
Page 1 and 2: NO. F037-775ISSUED: JUN. 15, 2009RE
Page 3 and 4: [a] NO ICE PRODUCTION -------------
Page 6 and 7: II. GENERAL INFORMATION1. CONSTRUCT
Page 9 and 10: [e] NORMAL HARVEST CYCLELEDs 5, 6,
Page 11 and 12: 3. CONTROL BOARD* A HOSHIZAKI exclu
Page 13: [b] FEATURESa) Maximum Water Supply
Page 17 and 18: f) Freeze Timer (S1 dip switch 9 &
Page 19 and 20: 5. FLOAT SWITCH[a] EXPLANATION OF O
Page 21 and 22: 7. SWITCHESTwo different control sw
Page 23 and 24: 2. WIRING DIAGRAM20
Page 25 and 26: IV. SERVICE DIAGNOSIS1. 10-MINUTE D
Page 27 and 28: 2. DIAGNOSTIC CHARTS[a] NO ICE PROD
Page 29 and 30: 1. See "II. 3. [d] ControlBoard Che
Page 31 and 32: 1. See "II. 3. [d] ControlBoard Che
Page 33 and 34: V. REMOVAL AND REPLACEMENT1. SERVIC
Page 35 and 36: 2. BRAZINGNote: All brazing connect
Page 37 and 38: 5) Remove the Drier using brazing e
Page 39 and 40: 9) Evacuate the system, and charge
Page 41 and 42: 19) Turn on the power supply.9. ADJ
Page 43 and 44: 7) Remove the Hose Band connecting
Page 45 and 46: 10) Install the new water tank in t
Page 47 and 48: 8) Connect the bin control connecto
Page 49 and 50: 5) Refit the removed parts in the r
Page 51 and 52: 2) Install the new Run Capacitor in
Page 53 and 54: VI. CLEANING AND MAINTENANCE INSTRU
Page 55 and 56: g. Wipe down the float switch housi
Page 57 and 58: [a] STAINLESS STEEL EXTERIORTo prev
Page 59: 4) Turn off the power supply and re

KMD-201AA KMD-201AWA - Hoshizaki

Create successful ePaper yourself

Delete template?

Save as template?