KMD-201AA KMD-201AWA - Hoshizaki

More documents

Recommendations

Info

2) Move the control switch on the control box to the "OFF" position.3) Wait 3 minutes.4) Move the control switch to the "ICE" position.5) Replace the front panel in its correct position and turn on the power supply.6) Allow 5 minutes for the icemaker to fill with water and the water pump to start operating.7) Close the condenser water supply line shut-off valve.8) Open the condenser water supply line drain valve.9) Allow the line to drain by gravity.10) Attach compressed air or carbon dioxide supply to the condenser water supply line drainvalve.11) Blow the condenser out using compressed air or carbon dioxide until water stopscoming out.12) Close the condenser water supply line drain valve.2. Remove the water from the icemaker water supply line:1) Turn off the power supply and remove the front panel.2) Move the control switch on the control box to the "OFF" position.3) Close the icemaker water supply line shut-off valve and open the icemaker water supplyline drain valve.4) Allow the line to drain by gravity.5) Attach compressed air or carbon dioxide supply to the icemaker water supply line drainvalve.6) Move the control switch to the "ICE" position.7) Replace the front panel in its correct position and turn on the power supply.8) Blow the icemaker water supply line out using compressed air or carbon dioxide.3. Drain the water tank:1) Turn off the power supply and remove the front panel.2) Move the control switch to the "SERVICE" position and move the service switch to the"DRAIN" position.3) Replace the front panel in its correct position and turn on the power supply for 2 minutes.55
4) Turn off the power supply and remove the front panel.5) Move the control switch to the "OFF" position.6) Replace the front panel in its correct position.7) Remove all ice from the storage bin/dispenser unit, and clean the storage bin/dispenserunit.8) Close the icemaker water supply line drain valve.56
Page 1 and 2:
NO. F037-775ISSUED: JUN. 15, 2009RE
Page 3 and 4:
[a] NO ICE PRODUCTION -------------
Page 6 and 7:
II. GENERAL INFORMATION1. CONSTRUCT
Page 9 and 10: [e] NORMAL HARVEST CYCLELEDs 5, 6,
Page 11 and 12: 3. CONTROL BOARD* A HOSHIZAKI exclu
Page 13 and 14: [b] FEATURESa) Maximum Water Supply
Page 15 and 16: [c] CONTROLS AND ADJUSTMENTSa) Defa
Page 17 and 18: f) Freeze Timer (S1 dip switch 9 &
Page 19 and 20: 5. FLOAT SWITCH[a] EXPLANATION OF O
Page 21 and 22: 7. SWITCHESTwo different control sw
Page 23 and 24: 2. WIRING DIAGRAM20
Page 25 and 26: IV. SERVICE DIAGNOSIS1. 10-MINUTE D
Page 27 and 28: 2. DIAGNOSTIC CHARTS[a] NO ICE PROD
Page 29 and 30: 1. See "II. 3. [d] ControlBoard Che
Page 31 and 32: 1. See "II. 3. [d] ControlBoard Che
Page 33 and 34: V. REMOVAL AND REPLACEMENT1. SERVIC
Page 35 and 36: 2. BRAZINGNote: All brazing connect
Page 37 and 38: 5) Remove the Drier using brazing e
Page 39 and 40: 9) Evacuate the system, and charge
Page 41 and 42: 19) Turn on the power supply.9. ADJ
Page 43 and 44: 7) Remove the Hose Band connecting
Page 45 and 46: 10) Install the new water tank in t
Page 47 and 48: 8) Connect the bin control connecto
Page 49 and 50: 5) Refit the removed parts in the r
Page 51 and 52: 2) Install the new Run Capacitor in
Page 53 and 54: VI. CLEANING AND MAINTENANCE INSTRU
Page 55 and 56: g. Wipe down the float switch housi
Page 57: [a] STAINLESS STEEL EXTERIORTo prev
show all

KMD-201AA KMD-201AWA - Hoshizaki

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?